Part numbers listed early in video! E39Source WEBSITE: www.E39Source.com BMW M3Source: / e65source BMW E46Source: / e46source
Жүктеу.....
Пікірлер: 171
@kurzjames6 жыл бұрын
He calls out the part numbers and socket sizes... This guy is good.
@mikelauerman76848 жыл бұрын
I'm a retired Senior Master BMW tech...Your E-brake vid was quite conclusive, as you covered the 'mystery hookup' of the Bowden cable to expander! Nice clean operation, better if you had applied some lubriplate to the friction area behind shoes on dust plates. I'm sure you have helped many with this tutorial. Thank you.
@vojtik1234
3 жыл бұрын
@@swar2000gmail no
@KyleMontanaro
2 жыл бұрын
Hi Mike, I've got an E39 (520i) and I've done the Handbrake adjustment several times (both before and after having replaced the Handbrake cables and shoes). I've followed the BMW manual (as well as the Bentley manual which says the same thing) down to the dot. For some reason, I keep getting the same results: Braking action starts on the second click but no matter how hard I pull, it's never strong enough to actually hold the car by itself on a ramp. The parts are of good quality. The manuals say to tighten the rear adjuster until the wheel can't turn and then back it off 12 clicks, then the rest is done from the front.
@Garageaholic4 жыл бұрын
11:20 - Thank you for so eloquently explaining how to get that small spring in. Love the idea of installing it FIRST, then wrapping the subassembly around the hub. genius. Good work! Frank
@judgegarry3 жыл бұрын
Ummm, Me commenting shows that this is a timeless video. LOL... This is probably the best of the bunch, on parking brakes. One thing I hope everyone does without fail is to use a proper RESPIRATOR, a paper dust mask isn't sufficient when exposing yourself to brake dust and contaminants left behind when changing brakes. Thanks @E39Source for making life simpler...
@kevedamanyo6 жыл бұрын
Just put a wheel bearing into my little bro's E46 323I, had to do some double checking on the parking brake reassembly and your video took care of it for me. Thanks!
@zanastumasonis8 жыл бұрын
quick tips: if youre doing this, loosen the cables, then adjust at the wheel area, after youre done do the final adjustment at the cable again, this way you will get the max brake
@ksukutube5 жыл бұрын
Excellent clear voice and good video! An important point I'd summarize for the viewers who want to adjust the brake without pulling the drum out comes around the time code 12:30. To loosen the parking brake, insert a flat-bed driver through one of the lug hole to reach the adjustment screw and pivot the flat-bed tip downwards (move your hand upwards) to move the parking brake adjustment screw one notch loose. To tighten it, pivot the flat-bed tip upwards.
@LogiForce867 жыл бұрын
Bedding procedure: Go 40 km/h, pull the handbrake until you feel it braking the car. Add one more click on the handbrake and keep 40 km/h for another 400 meters. Than release the handbrake and let the brakes cool.
@GalaxyT252 ай бұрын
Really really well produced vid. Congrats. I thank you for your work.
@Viperoloff019 жыл бұрын
Thank you very much for this video, this weekend it is discs pads all around and handbrake rebuild.
@edwardjablonski6219 жыл бұрын
Thanks a lot for taking the time to do this. I appreciate it.
@ASTActionCam6 жыл бұрын
Thanks so much for this. Everything was perfectly explained. Just did mine today. Far easier than I expected. Cheers
@brianobrian66372 жыл бұрын
THANK YOU again RYAN!!! Man; YOU have done QUITE a bit for the E39 Community!!!! I am quite appreciative!!
@E39Source
2 жыл бұрын
Thank you!!
@M0vir9 жыл бұрын
12:17 "You can do this with your wheel and all your brakes still on the car btw" This changed my life, I've always taken off the whole thing every time I want to adjust it. Damn
@alextasarov1341
3 жыл бұрын
I was about to do the same xD thank god I saw this first
@GoAlphaIce8 жыл бұрын
You know what you talking about, I like that you humble. Thank you!
@robertekman31639 жыл бұрын
Thanks guys! I had lot of help from your video! Especially where to start setting the shoes !
@allchuckedup488 жыл бұрын
I really enjoy these videos for the BMW cars I have 2- 46 Bmw 328i and an m3 both cars run great because of these good videos that I can go to whenever I need maintenance and can save money by not taking it to the dealer keep up the good work very informative
@55Rumble8 жыл бұрын
Thanks for this video.... I was going to be changing my rear wheel bearings but it turned into... Trailing are front bushes, Wheel bearings, And full brake rebuild including the Parking brakes and cables! Thanks for the pointers....
@tserevenad4 жыл бұрын
well done tutorial; good teacher, good narration, good camera work. nice job. thanks
@chrismcguirk71306 жыл бұрын
Great vid, helped significantly with my parking brake rebuild ...
@anthonym50508 жыл бұрын
Good job bro. thanks for the help. when it comes to reinstalling you can take the adjustment screw side and the first spring. collapse the two pads on the opposite end( just overlapping a little) spring goes in easier.. appreciate your Insight on this project..
@stephenparra75678 жыл бұрын
Very well done, thank you for the thorough explanation!
@robertkouzoukas42319 жыл бұрын
great DIY..great detail and easy to follow...thanks
@budharvesting8 жыл бұрын
Did my parking brakes with help from this video. Thanks !
@TheMarkLangmead9 жыл бұрын
Loved it - made me smile, great humour!
@smashervt6 жыл бұрын
Although you made this video a long time ago, Thank you for the detailed explanations! I used it to replace my Parking brakes and Rotors on my e46!
@HappyCapedogs9 жыл бұрын
Looks fairly easy. Just time consuming. Thanks for the great info.
@garytanaka10 жыл бұрын
Very interesting! I learned a lot from this video!
@nhhandyman6 жыл бұрын
I was looking for a refresher on my 95 e36 (after a complete bushing refresh) - almost exactly the same except the cable is attached via a pin so it stays in place. - well done.
@ericrollins43638 жыл бұрын
fantastic well explained video .
@VTafterbang10 жыл бұрын
Awesome video and timing. I'm about to do this on my 323ci.
@bionicfingerz10 жыл бұрын
Great video ! And .... I like the Xi 4 Snow License Plate :)
@andreblake20505 жыл бұрын
Great video. I am far more confident to take mine apart now. Thanks
@tommyleejonesqoq51578 жыл бұрын
Nice video .....wee bit dissapointed that u never replace doing all this - dust plates That is a pain in the back side In my car those are so rusty and bolts with the spring never hold the hand brake shoe I ended up drilling 5p coin and I bolt it together that way Passed my MOT on this temporary solution just about -16% is bottom line My parking brake was 16 I bought set of dust plates and a hand brake shoe kit Gonna get the new shoes (£25 Bosch )and the adjusting bolt with the part holding cable next week .... And at the summer time ( if we lucky to get any sun at all here in Belfast ) I going to replace the whole thing together on my e46 318ise Great video and of course 👍👍👍 Good luck 😎
@RealHank17917 жыл бұрын
Great video. thank you very much. Gotta do my 99 323i
@GeorgeAusters3 жыл бұрын
Good video man!
@AGN-zp8bw9 жыл бұрын
Great vid!
@hakimmalik36208 жыл бұрын
thanks dude, very informative.
@Richard-ts6mg9 жыл бұрын
Great video.
@mike-zn2rn9 жыл бұрын
great video
@Young_235 жыл бұрын
Great job!
@antonsmith43836 жыл бұрын
Great video. Thanks
@alexmackellar95608 жыл бұрын
Make sure your feet are bare to do this and any job in the garage.
@peterdiaz7957
7 жыл бұрын
No Name haha
@deltoidsforaltoids
5 жыл бұрын
1:19 for an explanation
@FraxinusExelsior
3 жыл бұрын
I would feel so naked and vulnerable...
@clubherbalife62924 жыл бұрын
Great jobs
@edwinromilly46459 жыл бұрын
It was a good video and informative..good camera work,maybe a tad more light boys,,but great vid..well done..
@MrBubba593 ай бұрын
I'm doing my E39 which is slightly different - adjuster is at 6 o'clock (difficult to see) but with many common parts.
@E36andE46vlog5 жыл бұрын
I taught it was pretty complicated, but it is okee doable! Good movie!
@bsouza16756 жыл бұрын
Thank you!
@kristofferellingsen71603 жыл бұрын
Thank u !
@candonjefferson26165 жыл бұрын
Thanks for this video
@TheEminit8 жыл бұрын
thanks video was helpful
@TheDirtyBirchTrails7 жыл бұрын
Thanx, awesome..Perfect !!
@ironmantooltime3 жыл бұрын
Excellent 👍
@wawa39128 жыл бұрын
thanks for the handy tip's
@rednightist9 жыл бұрын
That was a great video. If you have anything that illustrates replacement of the actual cable that would be great! Only one brake shoes expands when I pull the parking brake handle despite all hardware being new. I am guessing the cable has been stretched and needs to be replaced as well. (It is the only component that has not been replaced so process of elimination dictates the cable is the problem.) Thnx. again!
@barerobert9 жыл бұрын
Very informative, and very good explained. Thanks a lot for making this video, i still do not want to do the job though :p
@CptSnakeshit7 жыл бұрын
Does this apply to the E36 generally as well? Looks to be pretty similar from the part diagrams. Thanks for the great video anyway!
@briantwigley2 жыл бұрын
I’m here for the stupid hook thing that clips on to the cable. Took it off and couldn’t get it back on. This is the only video or resource anywhere that tells you. Thanks!
@benaddicott27069 жыл бұрын
good that people like you can be bothered to put the video`s up, i found it more understandable probley as your not an expert and did`nt come out with loads of technical crap a more experianced mecanic would, i had a fair idea of what to do but now after watching this im definitely more confident that i can do the job, so thank you and keep the vids coming....
@NathansBMWWorkshop8 жыл бұрын
I have never had this problem and i work on E46's almost daily, but i have had a few with the rear subframe mounts ripped out of the body, those are good times...
@08halit
8 жыл бұрын
+Nathan's DIY Garage did mine a month ago,,rear subframe reinforcements,,really a expensive jobb hopefully the jobb made from an auto mechanic ( worst ever) i knew more about service than that guy,reason i got to the man was off the price,,paid half but damn expensive either way ( 1000$ ) but i hope i can enjoy my e46 323 convertible..did you sell yours??
@08halit
8 жыл бұрын
+Nathan's DIY Garage i have handbrake probs,,one side brakes better then the other side...so this is the culprit,,i trued to adjust from inside,under the handbrake lever,but to no use,,now i know how to propperly adjust it..next is turbo or engine change
@NathansBMWWorkshop
8 жыл бұрын
I still have my 323i right now i need to get the interior done and put some miles on it since i just did the head gasket and time certs, luckily the subframe mounts are good on this car, it has 170k miles , i will be hoping to get $3000 out of it since its overall a nice car and it has the 5 speed manual, but i havent looked at the market lately so we will see, also like you said most most BMW shops dont know much they are shifting to more just switching engines and no diagnostics it seems.
@ironmantooltime
3 жыл бұрын
Both my e46 and e39 parking brake is useless. E30 was ok but not brilliant.
@Apelsiner99997 жыл бұрын
I see that you put the adjustment screw on opposite direction on the passenger side from your stock picture. Does it matter?
@g.king.6 жыл бұрын
thank you
@bearontree9 жыл бұрын
man you had it easy, in the M3 version of the brake shoe OEM kit the little spring that holds the brake cable side clipper is so SHORT!!! (2/3 of the length vs what you had) took me nearly an hour just to fit back one tiny spring. Had to pull so hard to get it back together, and there is almost no leverage point because the cable clipper need to be in place before the spring is placed back. Rest of it is easy enough. Now I just have to finish the other side....damn. Not sure why they made the M3 kit spring so much shorter, it sure is tight....
@leopold99996 жыл бұрын
Your the man!
@rednightist9 жыл бұрын
Also, a small note on the brake shoes. The OEM is definitely thicker than aftermarket replacements so DIYers, please take heed.
@millwrightman999 жыл бұрын
nice camera work , just doing mine and the front rotor retaining screws had to be drilled out but the back came off OK .terrible design for a parking brake , they always rust out & fall apart ., I even snapped one of the caliper bracket retaining screws , what a pain .
@samueldias20939 жыл бұрын
Thank you!!!!
@pastytit8 жыл бұрын
Thanks
@SPV1013 жыл бұрын
where is a good place to order all of these parts in the eu?
@MonoLucas1237 жыл бұрын
I'm guessing E36 is the same... i got something rattling like crazy on the rear of the parking brake so gonna have to check it soon.
@JMUDoc2 жыл бұрын
Make sure the dust shields aren't rotted because the quarter-turn spring pins can fall out... one of mine did, and the racket was absolutely apocalyptic - I honestly thought that my exhaust was dragging on the ground.
@vtmegrad984 жыл бұрын
The BMW E90 is also exactly like this.
@SGD3S1GN10 жыл бұрын
XI 4 SNOW, nice plate
@absgarage872410 жыл бұрын
What shift knob do you have?
@johnwellings32257 жыл бұрын
good enjoyable vid
@ANEL1010 жыл бұрын
The e38 is slightly different; being electronically controlled. But some components are the same
@khalid384 жыл бұрын
MERCI
@zigo19653 жыл бұрын
YOU could just remove the bracket with the rotor still attached and still able to grease your rotor pins, it saves some time, and makes it easier to hang the rotor.
@nodwaa92277 жыл бұрын
no shoes hahaha that made me smile
@salkodinamitas76813 жыл бұрын
I replace the spring kit and the pads but i reused my old rotor and that atachment on the cablee and i cant adjust the handbrake normal it when i do close to normal 10 clicks it sticks and brakes the whole time alone when i do 20 its too far away and wont hold do i need to resurface my inside part of the disc or what to do ?
@E39Source
3 жыл бұрын
It sounds like you just need to adjust the cable at the rear wheels. There is an adjustment wheel that can be opened or closed to bring the shoes closer to the rotor surface. 5-7 clicks should have the car held firmly on any incline.
@awiserbud8 жыл бұрын
nicely explained tutorial by the way. I have done these shoes many times and totally agree about the poor design. for a system that should only really be used when the car is stationary it amazes me how these brakes can become in such poor condition so quickly. most cars now incorporate the parking brake into the caliper which is better but still has room for improvement. the occasional top end vehicle uses a seperate caliper purely as a parking brake (a bit excessive in my eyes) but by far the worst modern design is the use of electronic motors for parking brakes. the french love this idea, us mechanics deffinately don't! And just to ruin our lives that little bit more certain models are now demanding diagnostic equipment in order to "wind back" these electronic calipers just to fit new brake pads.
@seanjordan6068 жыл бұрын
wait!!!! was that Jeff goldblums voice
@erkielva12424 ай бұрын
Currently struggling with my e39 handbrake. New shoes and springs on both sides but the left side cable from cabin adjusted to the max and basically 4-7clicks does nothing and locks it up pretty good at 8+ clicks. Right side is tight on 5+ clicks already. Pretty sure my cable is stretched and needs replacing but not 100% sure. You got any tips or tricks for making sure my cable is bad? Or how to change it easiest way. I think i have to remove the exhaust to change em and since all i got is one jack i dont really want to. Would be easy if i had a lift
@E39Source
4 ай бұрын
The brake should first be adjusted at the wheel with the screw adjuster as shown in this video, and then fine tuned and evened up with the cables at the handle.
@erkielva1242
4 ай бұрын
@@E39Source i did that, exactly AS the manual says, adjust till wheel no longer turns, 12 notches back and etc. When i went to adjust at cables then left one Is longer, like its at max and right is shorter, my mind tells me that the cable is stretched
@E39Source
4 ай бұрын
It is possible that it has stretched. It's also possible that the cable is not fully seated into the adjuster mechanism or the hooks that guide it under the chassis. To measure the cable for stretch, you'd need to remove it and lay it out flat. Exhaust removal would be required for replacement.
@baldolera9 жыл бұрын
Do all these parts come with the rebuild kit (PN 34212213311)?
@E39Source
9 жыл бұрын
***** Yes, thats like the perfect kit!
@dasfahrer81872 жыл бұрын
Pro tip: If you fold the brake shoes up like a taco and insert the spring, you can unfold them and the leverage does all the work. If you're replacing your hub anyhow, you can do it for both springs. Works for taking them off and putting them on.
@Taxman_DNB
Жыл бұрын
great tip :)
@rabmc
Жыл бұрын
Mmmmm Taaaaaaco’s
@kayvankomarizadeh18897 жыл бұрын
Great video, where do you live you have a lot if rust under your car.
@E39Source
7 жыл бұрын
+Kayvan Komarizadeh Ohio
@2012isRonPaul8 жыл бұрын
ho do u fine tune the cables? i've replaced all of the pads, 1 cable and even 'tuned' everything in place, but it still rolls down even from a fuking 0.00000000001% "hill" like there is no pads at all or smth.... P.S. - u installed both of the adjustment wheels exactly the opposite way that it was before...
@E39Source
8 жыл бұрын
+2012isRonPaul By fine tune the cables I probably meant inside the car, under the boot around parking brake handle. With the rotor off, have somebody pull the brake and make sure it's actually moving the pads.
@audunjemtland82875 жыл бұрын
My car stood still the whole winter, and the tires rolls partially some inches but suddenly haults. I can rock back and forth and have some rolling wiggle room, but the wheels won't roll all the way around. Isn't this something else than parking break? It seems locked.
@E39Source
5 жыл бұрын
It sounds like the parking brake to me. Raise and lower the lever in the car several times. If that doesn't do it, you may need to remove the rear wheel and hit those rotors with a mallet to get the shoes to break free.
@raulassis110 жыл бұрын
You might have to replace the brake rotors too. You see, your current rotors have a high wear from the inside where the brake shoes make contact.
@peterdiaz7957
7 жыл бұрын
that's just how they're shaped.
@peterfenwick4662 Жыл бұрын
How did you get the big spring in that goes on the opposite side to the adjuster?
@E39Source
Жыл бұрын
It's a pain. The spring with more coils goes on the bottom (at the adjuster). I use a long 90 degree pick to pull the spring and then have somebody push it into the brake shoe with a screwdriver.
@peterfenwick4662
Жыл бұрын
@@E39Source I've just been doing mine now, hence the question. Got it on using a long hex wrench, using the hub as a surface to lever it against. Took a while, but it's done.
@colmtully29436 жыл бұрын
HELP does anyone know how to knock off the rear brake sensors in 520i e39. i cant do any burnouts . the just stalls when i touch the breaks
@E39Source
6 жыл бұрын
Don't do burnouts. Tires are expensive. Also, the 520i likely doesn't have the power to do them anyhow.
@rkreimer107 жыл бұрын
no matter how many times I adjust mine, they keep auto tightening to the point I can't drive and have to adjust them. now sure wh
@adistanford10 жыл бұрын
If you want to bed in the new handbrake shoes, lift the handbrake while driving slowly for about 10 seconds, and then allow to cool off for two minutes. The main risk is doing it for too long, and causing the shoes to overheat.
@gtarules17 жыл бұрын
I don't have the handle, but the dashboard lever. I'm guessing no adjustment is needed for this part then. Just the shoes in the back.
@E39Source
7 жыл бұрын
E38 7-series? I have no experience with that part, but I would imagine that all of your adjustment is done at the rear wheels.
@BimmerM5e3910 жыл бұрын
The E-brake on E39's suck you can't do a handbrake turn. Only time the E-brake works is when the road is very slick. They might help shorten stopping distance if you are braking hard from high speeds in a straight line leveled surface I assume just don't expect it to stop the car.
@E39Source
10 жыл бұрын
BMWs don't have emergency brakes, they're "parking" brakes. Designed to hold the weight of the car on hills without relying on the transmission.
@millwrightman99
9 жыл бұрын
***** some call it tomato , others call it red and soft ., its still good on burgers
@arpcpro11 ай бұрын
Why do you say that they are completely destroyed? The springs don't stretch or something got broken or something not related.
@E39Source
11 ай бұрын
I meant the shoes, pad material had detonated, worn, and everything was very rusty.
@arpcpro
11 ай бұрын
@@E39Source Thanks. I will try to check my hand brake pads condition without removing the disc. My car failed MOT due to uneven hand brake, and the shop quoted me to replace the handbrake pads.
@E39Source
11 ай бұрын
@@arpcpro Brake rotor removal will be required to inspect the parking brake shoes.
@alexzracer20088 жыл бұрын
nice video. A lot of rust on the brakes. Why not buy a newer beamer? Looks like you have the money to buy one e39source.
@E39Source
8 жыл бұрын
+alexzracer2008 The 330xi is my "beater" that is on a fairly tight budget. I only need a winter weather car for one more year before I move to San Diego where I can enjoy my M5 daily!
@jozefchovan4261 Жыл бұрын
Ako vybrať tlačítko Bnv na ručnej brzdy
@zocagilera8 жыл бұрын
How many miles this car crossed? Thank's
@E39Source
8 жыл бұрын
228,000 miles.
@Hermetic_
7 жыл бұрын
E39Source: Awesome!
@procletnic8 жыл бұрын
My Bowden cable is too short and the expander body doesn't fully "close" thus making my pads touch the rotor even when the controlling screw (the one you can adjust with a screwdriver) is adjusted for minimum expansion. I tried to adjust the cable length from underneath the hand brake handle inside the car using the little screw but the screw is almost at the end of the little pillar it's mounted on. It's if the cable is too short? On the other side of the car I was able to set the hand brake without any problems. Can someone help?
@E39Source
8 жыл бұрын
If it's fully loosened in the car and at the rear brakes, I don't know what could be wrong. The cable should have an extra few inches of length in it for adjusting.
@procletnic
8 жыл бұрын
***** I've loosened it fully in the car but it's still not long enough, is there any other way to adjust the length? It doesn't seem to be stuck because I was able to win half a centimeter when adjusting it from underneath the hand brake handle (it was already on almost the loosest setting). Also, applying the hand brake does make the little head go further in. I'm beginning to think that the previous owner has cut the cable short for some reason and mounted a new head. From what I've read, replacing this cable is a pain in the ass.
@E39Source
8 жыл бұрын
I don't know of any other way to adjust it. You will likely need to replace the cable, which you're right, is a pain in the ass. Good luck!
Пікірлер: 171
He calls out the part numbers and socket sizes... This guy is good.
I'm a retired Senior Master BMW tech...Your E-brake vid was quite conclusive, as you covered the 'mystery hookup' of the Bowden cable to expander! Nice clean operation, better if you had applied some lubriplate to the friction area behind shoes on dust plates. I'm sure you have helped many with this tutorial. Thank you.
@vojtik1234
3 жыл бұрын
@@swar2000gmail no
@KyleMontanaro
2 жыл бұрын
Hi Mike, I've got an E39 (520i) and I've done the Handbrake adjustment several times (both before and after having replaced the Handbrake cables and shoes). I've followed the BMW manual (as well as the Bentley manual which says the same thing) down to the dot. For some reason, I keep getting the same results: Braking action starts on the second click but no matter how hard I pull, it's never strong enough to actually hold the car by itself on a ramp. The parts are of good quality. The manuals say to tighten the rear adjuster until the wheel can't turn and then back it off 12 clicks, then the rest is done from the front.
11:20 - Thank you for so eloquently explaining how to get that small spring in. Love the idea of installing it FIRST, then wrapping the subassembly around the hub. genius. Good work! Frank
Ummm, Me commenting shows that this is a timeless video. LOL... This is probably the best of the bunch, on parking brakes. One thing I hope everyone does without fail is to use a proper RESPIRATOR, a paper dust mask isn't sufficient when exposing yourself to brake dust and contaminants left behind when changing brakes. Thanks @E39Source for making life simpler...
Just put a wheel bearing into my little bro's E46 323I, had to do some double checking on the parking brake reassembly and your video took care of it for me. Thanks!
quick tips: if youre doing this, loosen the cables, then adjust at the wheel area, after youre done do the final adjustment at the cable again, this way you will get the max brake
Excellent clear voice and good video! An important point I'd summarize for the viewers who want to adjust the brake without pulling the drum out comes around the time code 12:30. To loosen the parking brake, insert a flat-bed driver through one of the lug hole to reach the adjustment screw and pivot the flat-bed tip downwards (move your hand upwards) to move the parking brake adjustment screw one notch loose. To tighten it, pivot the flat-bed tip upwards.
Bedding procedure: Go 40 km/h, pull the handbrake until you feel it braking the car. Add one more click on the handbrake and keep 40 km/h for another 400 meters. Than release the handbrake and let the brakes cool.
Really really well produced vid. Congrats. I thank you for your work.
Thank you very much for this video, this weekend it is discs pads all around and handbrake rebuild.
Thanks a lot for taking the time to do this. I appreciate it.
Thanks so much for this. Everything was perfectly explained. Just did mine today. Far easier than I expected. Cheers
THANK YOU again RYAN!!! Man; YOU have done QUITE a bit for the E39 Community!!!! I am quite appreciative!!
@E39Source
2 жыл бұрын
Thank you!!
12:17 "You can do this with your wheel and all your brakes still on the car btw" This changed my life, I've always taken off the whole thing every time I want to adjust it. Damn
@alextasarov1341
3 жыл бұрын
I was about to do the same xD thank god I saw this first
You know what you talking about, I like that you humble. Thank you!
Thanks guys! I had lot of help from your video! Especially where to start setting the shoes !
I really enjoy these videos for the BMW cars I have 2- 46 Bmw 328i and an m3 both cars run great because of these good videos that I can go to whenever I need maintenance and can save money by not taking it to the dealer keep up the good work very informative
Thanks for this video.... I was going to be changing my rear wheel bearings but it turned into... Trailing are front bushes, Wheel bearings, And full brake rebuild including the Parking brakes and cables! Thanks for the pointers....
well done tutorial; good teacher, good narration, good camera work. nice job. thanks
Great vid, helped significantly with my parking brake rebuild ...
Good job bro. thanks for the help. when it comes to reinstalling you can take the adjustment screw side and the first spring. collapse the two pads on the opposite end( just overlapping a little) spring goes in easier.. appreciate your Insight on this project..
Very well done, thank you for the thorough explanation!
great DIY..great detail and easy to follow...thanks
Did my parking brakes with help from this video. Thanks !
Loved it - made me smile, great humour!
Although you made this video a long time ago, Thank you for the detailed explanations! I used it to replace my Parking brakes and Rotors on my e46!
Looks fairly easy. Just time consuming. Thanks for the great info.
Very interesting! I learned a lot from this video!
I was looking for a refresher on my 95 e36 (after a complete bushing refresh) - almost exactly the same except the cable is attached via a pin so it stays in place. - well done.
fantastic well explained video .
Awesome video and timing. I'm about to do this on my 323ci.
Great video ! And .... I like the Xi 4 Snow License Plate :)
Great video. I am far more confident to take mine apart now. Thanks
Nice video .....wee bit dissapointed that u never replace doing all this - dust plates That is a pain in the back side In my car those are so rusty and bolts with the spring never hold the hand brake shoe I ended up drilling 5p coin and I bolt it together that way Passed my MOT on this temporary solution just about -16% is bottom line My parking brake was 16 I bought set of dust plates and a hand brake shoe kit Gonna get the new shoes (£25 Bosch )and the adjusting bolt with the part holding cable next week .... And at the summer time ( if we lucky to get any sun at all here in Belfast ) I going to replace the whole thing together on my e46 318ise Great video and of course 👍👍👍 Good luck 😎
Great video. thank you very much. Gotta do my 99 323i
Good video man!
Great vid!
thanks dude, very informative.
Great video.
great video
Great job!
Great video. Thanks
Make sure your feet are bare to do this and any job in the garage.
@peterdiaz7957
7 жыл бұрын
No Name haha
@deltoidsforaltoids
5 жыл бұрын
1:19 for an explanation
@FraxinusExelsior
3 жыл бұрын
I would feel so naked and vulnerable...
Great jobs
It was a good video and informative..good camera work,maybe a tad more light boys,,but great vid..well done..
I'm doing my E39 which is slightly different - adjuster is at 6 o'clock (difficult to see) but with many common parts.
I taught it was pretty complicated, but it is okee doable! Good movie!
Thank you!
Thank u !
Thanks for this video
thanks video was helpful
Thanx, awesome..Perfect !!
Excellent 👍
thanks for the handy tip's
That was a great video. If you have anything that illustrates replacement of the actual cable that would be great! Only one brake shoes expands when I pull the parking brake handle despite all hardware being new. I am guessing the cable has been stretched and needs to be replaced as well. (It is the only component that has not been replaced so process of elimination dictates the cable is the problem.) Thnx. again!
Very informative, and very good explained. Thanks a lot for making this video, i still do not want to do the job though :p
Does this apply to the E36 generally as well? Looks to be pretty similar from the part diagrams. Thanks for the great video anyway!
I’m here for the stupid hook thing that clips on to the cable. Took it off and couldn’t get it back on. This is the only video or resource anywhere that tells you. Thanks!
good that people like you can be bothered to put the video`s up, i found it more understandable probley as your not an expert and did`nt come out with loads of technical crap a more experianced mecanic would, i had a fair idea of what to do but now after watching this im definitely more confident that i can do the job, so thank you and keep the vids coming....
I have never had this problem and i work on E46's almost daily, but i have had a few with the rear subframe mounts ripped out of the body, those are good times...
@08halit
8 жыл бұрын
+Nathan's DIY Garage did mine a month ago,,rear subframe reinforcements,,really a expensive jobb hopefully the jobb made from an auto mechanic ( worst ever) i knew more about service than that guy,reason i got to the man was off the price,,paid half but damn expensive either way ( 1000$ ) but i hope i can enjoy my e46 323 convertible..did you sell yours??
@08halit
8 жыл бұрын
+Nathan's DIY Garage i have handbrake probs,,one side brakes better then the other side...so this is the culprit,,i trued to adjust from inside,under the handbrake lever,but to no use,,now i know how to propperly adjust it..next is turbo or engine change
@NathansBMWWorkshop
8 жыл бұрын
I still have my 323i right now i need to get the interior done and put some miles on it since i just did the head gasket and time certs, luckily the subframe mounts are good on this car, it has 170k miles , i will be hoping to get $3000 out of it since its overall a nice car and it has the 5 speed manual, but i havent looked at the market lately so we will see, also like you said most most BMW shops dont know much they are shifting to more just switching engines and no diagnostics it seems.
@ironmantooltime
3 жыл бұрын
Both my e46 and e39 parking brake is useless. E30 was ok but not brilliant.
I see that you put the adjustment screw on opposite direction on the passenger side from your stock picture. Does it matter?
thank you
man you had it easy, in the M3 version of the brake shoe OEM kit the little spring that holds the brake cable side clipper is so SHORT!!! (2/3 of the length vs what you had) took me nearly an hour just to fit back one tiny spring. Had to pull so hard to get it back together, and there is almost no leverage point because the cable clipper need to be in place before the spring is placed back. Rest of it is easy enough. Now I just have to finish the other side....damn. Not sure why they made the M3 kit spring so much shorter, it sure is tight....
Your the man!
Also, a small note on the brake shoes. The OEM is definitely thicker than aftermarket replacements so DIYers, please take heed.
nice camera work , just doing mine and the front rotor retaining screws had to be drilled out but the back came off OK .terrible design for a parking brake , they always rust out & fall apart ., I even snapped one of the caliper bracket retaining screws , what a pain .
Thank you!!!!
Thanks
where is a good place to order all of these parts in the eu?
I'm guessing E36 is the same... i got something rattling like crazy on the rear of the parking brake so gonna have to check it soon.
Make sure the dust shields aren't rotted because the quarter-turn spring pins can fall out... one of mine did, and the racket was absolutely apocalyptic - I honestly thought that my exhaust was dragging on the ground.
The BMW E90 is also exactly like this.
XI 4 SNOW, nice plate
What shift knob do you have?
good enjoyable vid
The e38 is slightly different; being electronically controlled. But some components are the same
MERCI
YOU could just remove the bracket with the rotor still attached and still able to grease your rotor pins, it saves some time, and makes it easier to hang the rotor.
no shoes hahaha that made me smile
I replace the spring kit and the pads but i reused my old rotor and that atachment on the cablee and i cant adjust the handbrake normal it when i do close to normal 10 clicks it sticks and brakes the whole time alone when i do 20 its too far away and wont hold do i need to resurface my inside part of the disc or what to do ?
@E39Source
3 жыл бұрын
It sounds like you just need to adjust the cable at the rear wheels. There is an adjustment wheel that can be opened or closed to bring the shoes closer to the rotor surface. 5-7 clicks should have the car held firmly on any incline.
nicely explained tutorial by the way. I have done these shoes many times and totally agree about the poor design. for a system that should only really be used when the car is stationary it amazes me how these brakes can become in such poor condition so quickly. most cars now incorporate the parking brake into the caliper which is better but still has room for improvement. the occasional top end vehicle uses a seperate caliper purely as a parking brake (a bit excessive in my eyes) but by far the worst modern design is the use of electronic motors for parking brakes. the french love this idea, us mechanics deffinately don't! And just to ruin our lives that little bit more certain models are now demanding diagnostic equipment in order to "wind back" these electronic calipers just to fit new brake pads.
wait!!!! was that Jeff goldblums voice
Currently struggling with my e39 handbrake. New shoes and springs on both sides but the left side cable from cabin adjusted to the max and basically 4-7clicks does nothing and locks it up pretty good at 8+ clicks. Right side is tight on 5+ clicks already. Pretty sure my cable is stretched and needs replacing but not 100% sure. You got any tips or tricks for making sure my cable is bad? Or how to change it easiest way. I think i have to remove the exhaust to change em and since all i got is one jack i dont really want to. Would be easy if i had a lift
@E39Source
4 ай бұрын
The brake should first be adjusted at the wheel with the screw adjuster as shown in this video, and then fine tuned and evened up with the cables at the handle.
@erkielva1242
4 ай бұрын
@@E39Source i did that, exactly AS the manual says, adjust till wheel no longer turns, 12 notches back and etc. When i went to adjust at cables then left one Is longer, like its at max and right is shorter, my mind tells me that the cable is stretched
@E39Source
4 ай бұрын
It is possible that it has stretched. It's also possible that the cable is not fully seated into the adjuster mechanism or the hooks that guide it under the chassis. To measure the cable for stretch, you'd need to remove it and lay it out flat. Exhaust removal would be required for replacement.
Do all these parts come with the rebuild kit (PN 34212213311)?
@E39Source
9 жыл бұрын
***** Yes, thats like the perfect kit!
Pro tip: If you fold the brake shoes up like a taco and insert the spring, you can unfold them and the leverage does all the work. If you're replacing your hub anyhow, you can do it for both springs. Works for taking them off and putting them on.
@Taxman_DNB
Жыл бұрын
great tip :)
@rabmc
Жыл бұрын
Mmmmm Taaaaaaco’s
Great video, where do you live you have a lot if rust under your car.
@E39Source
7 жыл бұрын
+Kayvan Komarizadeh Ohio
ho do u fine tune the cables? i've replaced all of the pads, 1 cable and even 'tuned' everything in place, but it still rolls down even from a fuking 0.00000000001% "hill" like there is no pads at all or smth.... P.S. - u installed both of the adjustment wheels exactly the opposite way that it was before...
@E39Source
8 жыл бұрын
+2012isRonPaul By fine tune the cables I probably meant inside the car, under the boot around parking brake handle. With the rotor off, have somebody pull the brake and make sure it's actually moving the pads.
My car stood still the whole winter, and the tires rolls partially some inches but suddenly haults. I can rock back and forth and have some rolling wiggle room, but the wheels won't roll all the way around. Isn't this something else than parking break? It seems locked.
@E39Source
5 жыл бұрын
It sounds like the parking brake to me. Raise and lower the lever in the car several times. If that doesn't do it, you may need to remove the rear wheel and hit those rotors with a mallet to get the shoes to break free.
You might have to replace the brake rotors too. You see, your current rotors have a high wear from the inside where the brake shoes make contact.
@peterdiaz7957
7 жыл бұрын
that's just how they're shaped.
How did you get the big spring in that goes on the opposite side to the adjuster?
@E39Source
Жыл бұрын
It's a pain. The spring with more coils goes on the bottom (at the adjuster). I use a long 90 degree pick to pull the spring and then have somebody push it into the brake shoe with a screwdriver.
@peterfenwick4662
Жыл бұрын
@@E39Source I've just been doing mine now, hence the question. Got it on using a long hex wrench, using the hub as a surface to lever it against. Took a while, but it's done.
HELP does anyone know how to knock off the rear brake sensors in 520i e39. i cant do any burnouts . the just stalls when i touch the breaks
@E39Source
6 жыл бұрын
Don't do burnouts. Tires are expensive. Also, the 520i likely doesn't have the power to do them anyhow.
no matter how many times I adjust mine, they keep auto tightening to the point I can't drive and have to adjust them. now sure wh
If you want to bed in the new handbrake shoes, lift the handbrake while driving slowly for about 10 seconds, and then allow to cool off for two minutes. The main risk is doing it for too long, and causing the shoes to overheat.
I don't have the handle, but the dashboard lever. I'm guessing no adjustment is needed for this part then. Just the shoes in the back.
@E39Source
7 жыл бұрын
E38 7-series? I have no experience with that part, but I would imagine that all of your adjustment is done at the rear wheels.
The E-brake on E39's suck you can't do a handbrake turn. Only time the E-brake works is when the road is very slick. They might help shorten stopping distance if you are braking hard from high speeds in a straight line leveled surface I assume just don't expect it to stop the car.
@E39Source
10 жыл бұрын
BMWs don't have emergency brakes, they're "parking" brakes. Designed to hold the weight of the car on hills without relying on the transmission.
@millwrightman99
9 жыл бұрын
***** some call it tomato , others call it red and soft ., its still good on burgers
Why do you say that they are completely destroyed? The springs don't stretch or something got broken or something not related.
@E39Source
11 ай бұрын
I meant the shoes, pad material had detonated, worn, and everything was very rusty.
@arpcpro
11 ай бұрын
@@E39Source Thanks. I will try to check my hand brake pads condition without removing the disc. My car failed MOT due to uneven hand brake, and the shop quoted me to replace the handbrake pads.
@E39Source
11 ай бұрын
@@arpcpro Brake rotor removal will be required to inspect the parking brake shoes.
nice video. A lot of rust on the brakes. Why not buy a newer beamer? Looks like you have the money to buy one e39source.
@E39Source
8 жыл бұрын
+alexzracer2008 The 330xi is my "beater" that is on a fairly tight budget. I only need a winter weather car for one more year before I move to San Diego where I can enjoy my M5 daily!
Ako vybrať tlačítko Bnv na ručnej brzdy
How many miles this car crossed? Thank's
@E39Source
8 жыл бұрын
228,000 miles.
@Hermetic_
7 жыл бұрын
E39Source: Awesome!
My Bowden cable is too short and the expander body doesn't fully "close" thus making my pads touch the rotor even when the controlling screw (the one you can adjust with a screwdriver) is adjusted for minimum expansion. I tried to adjust the cable length from underneath the hand brake handle inside the car using the little screw but the screw is almost at the end of the little pillar it's mounted on. It's if the cable is too short? On the other side of the car I was able to set the hand brake without any problems. Can someone help?
@E39Source
8 жыл бұрын
If it's fully loosened in the car and at the rear brakes, I don't know what could be wrong. The cable should have an extra few inches of length in it for adjusting.
@procletnic
8 жыл бұрын
***** I've loosened it fully in the car but it's still not long enough, is there any other way to adjust the length? It doesn't seem to be stuck because I was able to win half a centimeter when adjusting it from underneath the hand brake handle (it was already on almost the loosest setting). Also, applying the hand brake does make the little head go further in. I'm beginning to think that the previous owner has cut the cable short for some reason and mounted a new head. From what I've read, replacing this cable is a pain in the ass.
@E39Source
8 жыл бұрын
I don't know of any other way to adjust it. You will likely need to replace the cable, which you're right, is a pain in the ass. Good luck!
@procletnic
8 жыл бұрын
***** Thanks and thank you for your help :)
@trillbill8149
7 жыл бұрын
I