Another great video Doug. Being stubborn and not having a spare center cap, I measured to the top of the cap. The cap is 60mm in diameter, so I added 30mm to each measurement. It worked! not sure how but it did! Maybe this might help those without a spare cap like me

Thank you just thank you saved me $5k and you have every part in stock thank you

Great videos, I watch you all the time...good job.

Fantastic presentation as always, Doug. Rover On! 👊😎

@nathanuriel2073

2 жыл бұрын

instablaster

bilgilendirmelerin için çookk teşekkürler.

thanks i did this with Autel working perfect thanks

Nice video thank you.

I will be doing a re calibration tomorrow after replacing both front ride hight sensors. But I'm actually about to buy from you guys the coilover conversion kit for the 07 sport supercharged 4.2 . I've replaced the compressor and the control solenoid blocs 3 of them. And now the front sensors but it's still up in the back and slammed in the front. It won't lift but holds air. I figure it's a configuration thing. But I'm over the air ride and coilover conversion is definitely appealing. Maybe someone reading thins has an idea. Re calibration? Burn it ? Lol

I did it today. And i didnt saw this video. Actualy everything is the same excep measuring. You can put measurmens any you like from 365-520mm. Just do it for all wheels. Like i did 460mm for all wheels. You dont want to do more then 3mm difference between wheels. Because you will do it over and over. So do everything as said. But just put all same number to all wheels. And it will stand in these numbers after calibration. I learnd it hard way😂

Amazing! How do I get this app and dongle to adjust LR6 2006 height module? Thanks!

I just replaced a bag and will be getting an alignment soon, should this be done before or after the alignment? or both?

Well I called Land Rover dealership and a 2006 sport front 461mm back 464mm.

How do i get the app? Or blootooth device? I havr a Range Rover Sport HSE 3.00 diesel.. and want to calibrate the air suspension

How does this compare to the GAP iid tool? Any differences?

My measurements are all within 3mm of each other but it won’t complete a calibration the tool says one side is off -19 and so on. I don’t understand since all my measurements are so close within each other

what are the causes and solutions why my lr3 remain down ward for too long . please say something..

So 493mm is the spec, plus or minus 4 mm

I have a 2006 rrs supercharged... My car was fine and out of boredom i selected calibrate anti roll option then i got e 7 error code and my red suspension light is on... Everything still works ie suspension goes up an down etc but now the red light stays on and fault code C 1 A00-54 - Control module - System programming failure - missing calibration (AB)... 😮... Any advice please 🙏

Please, tell me why Land Rover lr3 front go down and remains downward ?

Hey. I tried 2 times to height calibration failed now my range rover sports l320 v8 2005 stuck on this code C1A00-54 and suspension light red light on. Please how get it back to normal. Thanks

will this work for the uk ?

Hi Doug, Just got my Iland tool from you guys. My LR4 2010 has lopsided suspension. One side is about 25mm higher than the other. How do i calibrate with that issue? I have drained the air all out and pumped back up again. Still lopsided. Any tips please.

@ptescreen18

3 жыл бұрын

stu jussi did U sort this out I have same issue , mine suspension is out all over and needs to be all level again

Please teach me. Launch calibration suspension X431 Range Rover 2004

Hi , i just adjusted the rear hight sensor lever arm to get loeer hight on the rear .. is it fine or it will cause issues?

@ossaidamg5750

5 жыл бұрын

I adjusted both sensors arms *

Will this allow me to adjust my normal ride to be 2 in higher? I got larger tires

@313mikido

6 жыл бұрын

I would think i can enter a different value than what i actually measure to trick the computer to raise.

@TheKingofHowTos_TKHT

6 жыл бұрын

yes you can

Bonjour Existe t'il en français.?

Tried the calibration today with the result of a dead LR3. All was working fine up to this point, there was a difference in the rid height rear left to right which I wanted to resolve The error code is C1A00-54 Control Module "permanent". It's the main Ride Level Module. Can't delete this error, no way to get the vehicle back to normal, it sits in the suspension bump stops undrivable. Is there any ILand diagnostic support group online? Could not find anything.

@garrykennedy5484

2 жыл бұрын

OH Crap!!!!!!! I was going to get this to level my right front being 1/2 inch too low. Now I see you haven't had a response????? Did you ever get this sorted using their tool?

Hi, where can I get it and what is it called ? Thanks

@atlanticbritishrp

4 жыл бұрын

www.roverparts.com/iland/

It is ridiculously difficult to re calibrate the suspension

Hi, this Faisal here, i am running a Range rover sport 2008 model, i have changed the higher sensors, but its asking air suspension hight calibration, can you able to help me how to fix it ? Would appreciate if you can share your email id or whatsapp number

I did not understand for whom created this application. If for car services, then they already have other, no less functional programs for which they have already paid money. And it is unlikely that they will buy this product. And if for ordinary owners of cars, I want to ask : do you fuck in your brain??? $ 400 ??? And this is for the version with limited functionality . My LR3 for 10 years and all this time I have not spent so much money on the diagnosis and calibration of anything in the car. And Yes , there is a sufficient number of generally free programs that have the ability to diagnose and calibrate many functions , and they are compatible with different brands, not only with land Rover.

This guy is way off, it’s not that easy it will reject calibration over and over. This iLand tool is a piece of junk it’s trash don’t waste 400 bucks on this piece of junk just pay to have it done

what are the causes and solutions why my lr3 remain down ward for too long . please say something..