I did this conversion a few months ago on our '10 LR4 , I don't miss the air suspension all that much. The piece of mind of less components to fail on my 120K+ mile 11 year old vehicle is nice.

Probably the best instruction video I have ever watched, to the point and lots of handy tips

Does this guy know what a legend he is among Land Rover owners? Came to watch this video and it was like seeing an old friend.

When he struggles at 15:01, I found the trick to to have someone put their weight on the wheel hub, to push the suspension assembly down. Then the coil will go in easily.

I dont even need to do this to my lr3 but he did such a good job narrating this video that I got mesmerized.

Master instructor. Will definitely do this upgrade the next time I have an issue with my air suspension. Thank you!

What a perfect job... I am no longer afraid of Land Rover vehicles...

2006 LR3 : Spent most of my first day trying to get the shock up into the sway arm -- Pro Tip: Don't raise just one side of the vehicle, I did, and it actually works against you by loading the sway arm with tremendous energy, do front and then back. Stay tuned for my next update. What a difference doing the front (or rear) first makes, the passenger side took me literally 8 hrs this morning, while the drivers side was just under an hour. First impression of the lift is....Wow, the front is noticeably higher, almost to the point that you need to pay attention of the finished height as you might not make it out of the garage especially if you have a roof rack. Tomorrow is the rear...stay tuned

@WDMorts

4 жыл бұрын

Did you have any issue getting the HD spring onto the shocks, currently have the rear on but cannot get the spring compressed enough to get the top bolt on.

@ritc

3 жыл бұрын

I know you posted this a year ago, but I think what you're describing may be my problem. I am using a floor jack and two jack stands, and performing the conversion a single corner at a time. I've managed to complete the rear wheels, stepping on the break rotor to lower the wheel assembly enough to slip the strut up into the upper strut bracket. But on the front, with just the driver's side front wheel raised, I have a whopping 2.5 inches to cover to line up the hole on the strut hangin below the hole on the wheel assembly. Is it as simple as equally raising the front passenger side of the vehicle? 2006 Range Rover Sport. Thank you in advance for your feedback.

Just finished this after 8 hours on my LR3 a couple days ago. The rear struts seemed impossible to get into position, but then I realized you can drop the bottom in, align the top where you won’t bend a bolt when you kick it past the housing, and kick the rear strut into place. The rear housing has enough give that it will bend out of the way for a split second and pop right back. Yes, you’ll scratch the black paint on the pretty new strut just a little, but oh well. It made getting the rear struts into place to be bolted in like a 1 minute job, instead of a 20 minute wrestling match. Also, PB B’laster spray and a 2-foot breaker bar plus a 2-foot metal pipe helped with the nearly 400 ft-pounds I needed to release the bottom rear nut on each side! When you retorque them in the end, they only need around 221 ft-lbs however. And yeah, the smooth air ride has been downgraded a little to a regular SUV ride now, but nothing bad or unusual. The body has a little more sway in the turns, but this isn’t a sports car anyway. And it still goes through the rough cow pastures now just like any SUV or pickup. I did 80 down the Interstate, and it felt perfectly stable and boring as well. And your video helped my confidence a lot, so thank you!

Good video, going to try this today. So fingers crossed. Thanks for putting this up

Love your program my brother from all the way in jamaica 🇯🇲 love it love it you make it so simple kool

nice. im getting a used sport and this is the number one problme most owners are afraid to tackle

Cant wait to get my coil suspension for my lr3

Great video, it helped a lot, thanks

This is perfect and easy. 2007 Range Rover sport. The wiring wasn’t explain clearly for the ground wire. It is used the ground wire from the white plug towards the engine and connection with the wires with the harness towards the rear of the vehicle. The rear shock was a pain the butt.

Took me 6 hours in 2 afternoons sessions in the drive way. This is the standard on how to complete thus task. The only thing I will add to anyone starting is you need to be patient with the bottom bolt alignment. Get creative and you will get it aligned and done. I am going to knock out the flash tomorrow and will update after the flash.

Just going to hire you guys!

great video

Good video my man👍

you made me want one

Thank you 🙏

Amazing coils spings it is then.💯💥👍🏻👍🏻👍🏻👍🏻

I have a 2008 LR3 with DSC. Should I disconnect the height sensors during the conversion? You mentioned it in passing and i need to make sure I don't create any issues for myself if I disconnect them. I purchased the AB Part L319SRK/L320SRK last year (just now getting to it this Xmas break) and the instructions state to "disconnect the electrical connectors from all four height sensors and wire tie them to prevent contact with any moving components". Here's to hoping you get to this during the Xmas break!

Nice one, I hope this shocks could work with a 2003 HSE model cos mine just got busted with a sound as loud as a bomb while trying to raise the front suspension

Parts are of highest quality, very pleased with parts. If you think this is a one person job, you are completely out of your mind. Front struts, PIA, but doable. Rear strut removal no fun, but doable. I came in to watch this video again and again to see how he managed to install those new rear springs, and he conveniently cuts out, then comes back with the spring installed, saying it can be a "wrestling match" I have been "wrestling" with the first rear spring for 3 hours until my arms simply gave out. 3 people, two crow bars, and a ton of swear words, I could not maneuver rear spring in place. Any hints appreciated

@michaelpapp894

6 жыл бұрын

This all happened last Friday. Friday evening I made this comment, and sent a "help" request to Atlantic British. By Monday, I had not one, but TWO people from AB call me to help, and it all boils down to - I needed a bigger crowbar. A 3 or 4 foot crowbar, and your LR3 will just laugh at you. Seriously. I went to Ace, asked them for the biggest crowbar ever created by humankind, and was sold a 5 foot solid steel bar. My LR3 cried uncle, And Life was good again. Thank you AB!

@mks_95al_ghamdi91

5 жыл бұрын

How much hours it will take to install the 4 coils spring.

@michaelpapp894

5 жыл бұрын

@@mks_95al_ghamdi91 WITH a 5-6 foot crowbar and a helper, count on 6 hours. Without helper, figure 9-10 hours, without 5-6 foot crowbar, not until the earth crashes back into the sun. The design & workmanship on the parts by Atlantic British is OUTSTANDING, their support is top notch, but you are working with heavy springs and a suspension that does not like change.

@mks_95al_ghamdi91

5 жыл бұрын

@@michaelpapp894 hhhhhh appreciate the quick feedback. My question was to check if i can manage to install the coil spring for long vacation in rough areas for far overlanding, and after that go back and reinstall the hydraulic system, now it seems fantasy.

@michaelpapp894

5 жыл бұрын

@@mks_95al_ghamdi91 In my humble opinion, your best bet would be to purchase an LR Discovery Series II for your trip, & re-sell it when you are done. The only off-roading I would trust my LRIII for would be pulling into my driveway or a parking lot. I never felt that way about the LRII

Hey thank for sharing,how many hours it takes to do it.thank you

Great. Thanks.

Just got my kits today💪

@bassnjeep6537

3 жыл бұрын

Have you got them installed ?

@manihussain8688

2 жыл бұрын

How much for kit?

@stephonhines6554

2 жыл бұрын

@@bassnjeep6537 it’s a different ride

@stephonhines6554

2 жыл бұрын

@@manihussain8688 I paid 1000$

Excuse me sir, I am from Cambodia I have change that suspension already, so how can I get that bypass?

NICE SIR

Do you install CDL linkage for D2s? Do LR3s have a CDL option?

ive done this conversion and my vehicle is in coil mode but the warning light and 30mph message+sound keep comes up. what should i do?

Hey, the original coil spring vehicles have a kind of hook on the lower wishbone arm, front, what the air suspension does not have. can you tell what that hook is for?

I have a ‘06 RRS 4.2litre S/C, and I want to convert to a LOW profile coilover kit. Can you please recommend a kit for me? I will add however I don’t plan on driving off-road, or doing any towing. I have been told to go with “King Springs”, but the right strut with a suitable top hat is hard to find. Thanks from Queensland Australia

I’m installing but the rear coils are not lining up at the base plate. Base plate flat side with hole is facing to the back corner of the vehicle. Only one way the top bolts align.

Hi Doug, I have a 12’ Sport and my mechanic is telling me if I go to spring coils that the traction control features will not work anymore but after watching the video it looked like there’s an add on drive that allows you to still use those features. Help!

We bought the coils suspension kit. Coils are in, it started and was able to test drive, it was fine, now it won't turn back on to test drive. We haven't overrode the module yet. We don't understand how we were able to test drive it one day and can't the next. When we override the module, will that fix that problem?

Will I install 275 70 18 tires with this suspension to the RRS? I have just ordered this kit for my RRS and I am wondering what tires will fit

I like I give 100 from Puerto Rico thanks

Is there a kit now thats comparable to this with the Old Man Emu brand parts for 2007 Range Rover HSE 4.4L? I am now experiencing suspension issues. The front has dropped and wont raise , getting c1a00-54 and c1131-92 codes. Do you ship to the USA?

Hello I have a 2006 lr3 I want to do this to. How can I find out the correct numbers I need and is there also a way to lift it a tad higher.

It’s show this amber light or not?

Question. to ALL.. What kit is the best to get Lift 4 inches range rover 2008,i understand with this Kit change of Air To coils spring, but how get lift 4" or 3"?? many thanks regards

I couldn't find a listing for the 2013 L320 RR Sport SC. Do you make a coil conversion for that model?

Hi. Will your EAS Flash Device be able to (theoretically) allow for an engine conversion? Lexus V8 or similar.

@atlanticbritishrp

5 жыл бұрын

Hi Nicholas, Our EAS Flash devices are programmed specifically for our air-to-coil kits to help reset the programming for moving from EAS to Coil. The re-flash device will not work with engine conversions.

For an L322 3.6 year 2010 you have a suspension conversion solution?... Thanks

Do u have the regular struts for 06 land rover lr3?

What do you do with the air hose just leave it up there?

Great video maibe I’ll be buy this kit to my lr3 hse 2006 I’ll think about this... one question the air lines what you do it?

@mark9559

5 жыл бұрын

cut them and leave them hanging also the wire plugs should be unplugged at each wheel

Hi..How many hours estimate for mechanic to do after he see's this video ? Can you direct me to Air Ride parts..what is the part that most commonly fails in the Air Ride ? Thanks

Is there a website where I can buy the coil over and pigtail please om having the same suspension fault problem with my 07 range rover hse should off waited till the video ended to see the website

Am trying to put coil shocks

8 hours in still can’t get it lined up any suggestions? Could really use the help

Do you have any contact that does this work in California????

Is it compatible with a range Rover sport with ace bar?

my lr3 has air and no leaks only that when you turn left the suspension lowers, so if i buy your spring will this stop faults

@atlanticbritishrp

5 жыл бұрын

Hi M&T, our air-to-coil conversion kit comes with a re-flash device for your LR3 to clear the codes after you install our air-to-coil conversion kit. You can find out more information about it here: www.roverparts.com/Parts/L319SRK-OME

Will this kit Fit the 2006 lr22 hse 4.4?

What did you do with the airline with the front strut you installed

@ironnads7975

4 жыл бұрын

He clearly shows what he did with that airline in the video

Did you need to remove the Ace system?

So what do you do with the airlines and pump?

@simonwilkinson9327

5 жыл бұрын

Leave it there..

My mechanic advised against the spring shocks. All he said was they’re bad. Can some please advise whether to stay with air or go to springs? Help please

@Jarlzdotorg

2 жыл бұрын

i'm guessing the mechanic is answering for their bottom-line/ residual income; i'm doing the whole conversion/swap; 1x; 1,000 miles into ownership; hopefully never have suspension issues again!

Se lo puedo hacer a mi 2007 sport supercharged?

Is maintaining the air suspension really that much of a problem on older L322's?

@atlanticbritishrp

5 жыл бұрын

If money is no concern, then no.

@volvo24091

3 жыл бұрын

Self serving reply by AB above. This kit would cost more than maintenance.

do this suspension go high or low as high mostly is for off-road

@atlanticbritishrp

4 жыл бұрын

it adds about 2-inches over stock height.

Where yall located? Wanna come do mine in Georgia?

Went you buy this kit does it come with a video how to by pass the system

@atlanticbritishrp

5 жыл бұрын

Hi Johanna, our Air-To-Coil kits come with detailed instructions on how to set-up the EAS re-flash device.

Do you ship to South Africa and does it fit LR3 2.7 tdv6?

@atlanticbritishrp

4 жыл бұрын

Hi Shoemans, since the diesel versions aren't available in the states, we haven't been able to test the systems on one. If you would still like to purchase one you are more than welcome to, just be aware that these were manufactured for US petrol models. As far as international shipping is concerned, please fill out our contact form here and one of our reps will get back to you with a custom quote: www.roverparts.com/contact/

I really want to do it myself, but i don't have the necessary equipments. How much does a conversion usually costs?

@ritc

3 жыл бұрын

I was quoted $1,000 by Land Rover, and about $800 by a shop that works on Land Rovers. Doing it my self, and cursing a lot.

@stateservant

3 жыл бұрын

@@ritc Nice, but you save money huh? Cursing brings result afterall.

Does it still ride the same with regular shocks am thinking putting regular shocks on my Land Rover L3

@atlanticbritishrp

5 жыл бұрын

There is a kit version also available with standard load struts as well... www.roverparts.com/Parts/L319SRK-A

@Camron-zd8wp

3 жыл бұрын

@@atlanticbritishrp i tried setting the "notify me" but it say enter valid email..

Hi, I leave in the UK and being trying to order a set of this Heavy Duty LR3 Spring but to no avail. Please how can i place an order?

@WDMorts

4 жыл бұрын

Devon4x4 sell the OME +50m springs.

what size a/t tires can I put on with 20" rims? after spring install.

@gandashable

5 жыл бұрын

i have 275 40 20

@ritc

3 жыл бұрын

I am running 285 50 20 after I finally get the front fully installed - can't seem to get the bolt installed on the bottom of the strut - any suggestions welcomed. I'm converting from air struts w/ 3" Johnson lift rods. The rear coil springs are installed, they were easier, and the height is magic.

Where can I purchase the bypass module I already have the conversion kit installed in my 2006 Range Rover sport hse 4.4

@miami305hits

2 жыл бұрын

I don’t think they have one yet

Brembo brake calipers part #? Or where could I find a kit for front and back ? 08 hse

@atlanticbritishrp

3 жыл бұрын

Make sure you select your year and vehicle model at top of page: www.roverparts.com/brakes/calipers-cylinders-hydraulics-vacuum/

What's the cost of the conversion for an LR3?

@stephonhines6554

2 жыл бұрын

I paid 400$ for the work an a thousand an something for the parts

How can I buy just the reflash

I take it that these will fit the LR4? every time I pull up LR4 it also shows LR3, is this correct, Please.. thank you.

@atlanticbritishrp

5 жыл бұрын

No, the kit shown in the video fits: LR3 / Discovery 3 V8 4.4L | '05 - '09 LR3 / Discovery 3 V6 4.0L | '05 - '09 Range Rover Sport | '06 - '09 Range Rover Sport Supercharged | '06 - '09

@chadwhiteoverlyexposed9929

4 жыл бұрын

Is there a kit for the LR4?

@user-su8xv8lr4s

3 жыл бұрын

@@atlanticbritishrp is there a kit for L322?

Great job. I do have an L322 Range Rover Vogue 4.4, its a 2005 model. It came with coil suspension from the previous owner except the rear is too low as compared to the front. What would you recommend?

So I did this and no matter what I do, I get all the dash lights come on. I try to hook my icarsoft device into the obd2 port and it can't connect to the transmission and several other systems. Is there another device I can use to make this work??

@atlanticbritishrp

5 жыл бұрын

So if you installed our kit and the EAS override module provided has not cleared your codes after a few vehicle restarts, please call us at 800-533-2210 and describe your problem to customer service and ask for tech support. Please have your customer number and invoice number handy when you call.

@akowalters6885

5 жыл бұрын

Remove the dash and pull out the bulbs

@JohnWick-cr7mu

4 жыл бұрын

Did you manage to sort this? I did the conversion last night and the reflash didn’t work for me either.

@KoRb333

3 жыл бұрын

@@JohnWick-cr7mu mine isn’t working either, I can’t change terrains

It's come with the red box?

@atlanticbritishrp

4 жыл бұрын

EAS Override Module? Yes, included... www.roverparts.com/suspension/air-coil-suspension-kits/L319SRK-OMEHL/

I have a 2008 HSE Sport that was converted to coil springs several years ago and I do not know what kit was used. Can the reflash be used to clear the suspension warning light? Also, the car has recently started acting crazy. After driving from 5 to 15 minutes it will shut down the Nav system, the radio, the info screen, the blinkers but turn on the emergency flashers all by itself. The battery is new, when I crank it up the battery has 14.4 volts and will eventually draw down to 9.7 but keeps running. If I shut it down it will not crank or even make a sound but if I let it sit for 15 minutes the battery will be back to 14 volts and it will crank right up. Nobody that I have taken it to has a clue but they want to keep it for several days to run tests

@atlanticbritishrp

6 жыл бұрын

Have you taken it to a shop that specializes in Land Rovers? If not, we might be able to recommend one if there is one in your area. What city/state/zip are you?

@atlanticbritishrp

6 жыл бұрын

It sounds like you're having alternator issues...while the vehicle is running it's not charging and allowing the battery to drain trying to keep the systems running. As it drains, it starts prioritizing the engine over ancillary components, and will eventually shut down. As for the recharge, a strong wet-cell battery will recharge on its own.

@bluec6437

6 жыл бұрын

Yes, I took it to the RR dealer in Birmingham, AL and also to a private RR shop, Road Britannia Ltd, in Atlanta. We have Eagle Imports here in Auburn, AL that has been doing service work. The RR dealer and Road Britannia refuse to work on the car due to the coilover conversion. Eagle Imports said the alternator is good?

@bluec6437

6 жыл бұрын

Auburn, AL 36832

@bluec6437

6 жыл бұрын

Is it possible for the alternator to charge when first cranked up and then shut down? When I first start the rr the battery shows 14.4v but when it starts shutting down systems it can drop to below 10v. After letting it sit a while I can crank it back up and the battery show 14.4v.

what do you do with the air compressor?

@stephonhines6554

2 жыл бұрын

Nothing

Ola amigo Parabens pelo vídeo, estou com sérios problemas na minha Land Rover Discovery 03 2005 na suspensão pneumática, vou colocar molas helicoidal, mas preciso reset no sistema, como consigo comprar um aparelho igual a este que o senhor esta usando.....fico imensamente grato se possível compartilhar ou sugerir um lugar onde eu consiga encontrar e importar. .. .... Hello friend Congratulations for the video, my name is Herminio I'm having serious problems in my Land Rover Discovery 03 2005 in the pneumatic suspension, I'm going to put helical springs, but I need to reset the system, how can I buy a device like the one you are using .....I am immensely grateful if you can share or suggest a place where I can find and import.

I have range rover I would like change suspension Where u shop?

can 2.7 lt diesel engine be done, is there anyone in UK or Ireland importing this, or are they made in europe

@atlanticbritishrp

6 жыл бұрын

You should check with Terrafirma/Allmakes in the UK... they offer kit options I believe and may be able to recommend an install shop in your area.

Combien coûte les quatre amortisseur usa

Es posible para discovery 1 esta clase de amortiguadores??

@atlanticbritishrp

4 жыл бұрын

Llevamos un kit de suspensión para el Discovery 1, puede encontrarlo aquí: www.roverparts.com/Parts/TF204

@fernandobeltran1701

4 жыл бұрын

@@atlanticbritishrp escribo desde.bta Colombia. Me gustaria saber si los pueden enviar a esta ciudad. Y si puede un.numero de contacto para whatsapp

@atlanticbritishrp

4 жыл бұрын

Debido a las complejidades del envío internacional, deberá completar nuestro formulario de contacto aquí (roverparts.com/contact) y alguien le enviará un correo electrónico sobre un presupuesto de envío personalizado.

Couldn’t you just clip the airlines? I mean that wouldn’t affect anything would it

Great video, Thanks a lot! :) Кому надо инструкцию по установке пружин на русском языке - пишите. Скину!

@shymkent5247

3 жыл бұрын

Скиньте пожалуйста

@vladimirshnaidt9493

3 жыл бұрын

Скиньте инструкцию на русском, пожалуйста.

Combien coûte une pièce

Our vehicle rides very high. Bought second hand

@kingprince3793

Жыл бұрын

Atlantic British suspension?

After installing everything including the module, my dashboard is lit up with warning , abs, and brake lights all lit up

@kingprince3793

Жыл бұрын

Did you ever get it right ?

@roesamon5213

Жыл бұрын

@@kingprince3793 yup...

bit of a wrestling match who won Brock lesnar LOL

Yeah, let's get rid of one of the best features on a range rover 🤦‍♂️😆

@rgfc1114

3 жыл бұрын

Exactly, and whilst we're at it lets kill the exemplary ride that it has at all weight variations on it's air suspension... If you want a Toyota people, go and buy a Toyota.

@MethmalDhananjaya

3 жыл бұрын

Ok Genius.

hello I ordered the kit on eBay by their company but I only received two suspensions out of 4 it's been three days that I've been waiting for an answer but none I'm going to have to return the product when I would have liked to receive my complete order @atlantic British

Excuse me sir, I am from Cambodia I have change that suspension already, so how can I get that bypass?