Thank you Mr. Pete for the suggestion. I think I will go with this one.

@peteshobbies5383

Жыл бұрын

Good choice 👌 👍

Wow that really does have minimal overspray , as a hobbyist now , I find the big guns really do create an issue for the guy that wants to spray in the garage or workshop , so I can see how that’s a great gun especially for the home DIYer

@peteshobbies5383

2 жыл бұрын

Hi Roger, yes, exactly, spray painting in quite anti social at the best if times so there's definitely a place for these guns, not fast but most hobbyists painters won't be in a huge hurry most of the time, hope alls well with you mate 👍

Hi Pete, that’s an impressive little gun I’m impressed by the lack of overspray there looked like that there was none on your bench at all! It’s obvious that it’s a very slow gun compared to your others but I would think this will make it ideal to a beginner. The tank and wing both came out really well. Cheers mate see you in the next one.

@peteshobbies5383

2 жыл бұрын

Hi Steve, yes, a cracking little gun, i got this off the same chap i got the purple cap guns from with a cup, a real bargain so very happy with it, as you say, ideal for beginners and the chap at home especially because of the low overspray, cheers mate 👍

Pete, I always watch your videos with great pleasure. 🏅🏆

@peteshobbies5383

2 жыл бұрын

Thank you Boyan, very much appreciated 🙏

Aku dapat menikmati vidio anda dengan teks bhs. Indonesia. Trimakasih pete

@peteshobbies5383

6 ай бұрын

Hai Sobat, Bisakah kamu mendapatkan subtitle bahasa Indonesia di KZread sekarang?

@saifulamri1829

6 ай бұрын

@@peteshobbies5383 tidak semuanya bisa.

Hi mate ideal for small compressor and small workshops cheers mate 👏👏👏

@peteshobbies5383

2 жыл бұрын

Cheers Dean 👍

Hey Pete, what a great little gun it really sprays well. The split nozzle tech is really coming into it's own with the low air pressure needed to get as good a finish (if not better) than the standard tip that needs 2bar, I bet other manufactures are itching to have this tech in their guns but I assume they have to wait until the patent runs out but isn't the usual length 20 years🤔 I don't know much about them🤷‍♂ Anyway the Wider1L did a fantastic job on the base and clear but as you mentioned it's a bit slow for a 1.4 but it's a very capable gun, thanks for doing another great video mate👌👍

@peteshobbies5383

2 жыл бұрын

Hi John, yes, it's a great little gun, not cheap but really good, there's something rather satisfying about using such low pressure and getting really good results, plus there's virtually no overspray, brilliant for the person at home, cheers buddy 👍

@JohnWD40TC02

2 жыл бұрын

Yeah it certainly laid the clear on really nice, not quite the same but it was nice using the AZ4 at a low pressure and finally getting a good finish from it👍 I didn't get the ws400 I told you about, I've decided to wait and hopefully get the new series2 when I can👍

@peteshobbies5383

2 жыл бұрын

There's not many bad guns out there really, as you know, you can use just about anything and get good results these days because you know what you are doing, before you were looking to the gun for results where as now you just take it in your stride. There's no denying the new WS400 is good, i just don't think it any better than the old one set up the same, funny thing is, i got that 1.4HD tip set the other day and in the gun it lines up almost at 90°, more fun and games now then, cheers mate 👍

@JohnWD40TC02

2 жыл бұрын

Yeah I have noticed that these days I can pickup a gun and get a descent finish out of it, if not the first time then I can soon dial it in, a couple of years back I was always blaming the gun and wasting more cash on them. Good news about the 1.4HD tip mate, it's strange then that the other one didn't line up🤔🤷‍♂

@peteshobbies5383

2 жыл бұрын

Yes, very odd re the tip, I've got 1.3, 1.4 and 1.5 and they all sit slightly differently when torqued to the same value, one thing i do know is lining that cap up to 90° of the slits really does make a difference to the way they spray, haven't tried the new LS and OBS so can't comment but i have been trying the LS400 series1 for clear as someone suggested on here, i lined the tip up and it was really really good, quite impressive, cheers mate 👍

Thank you very much for your videos they are great and full of information. However, do you think the ANEST IWATA WIDER4L-V16J2 1.6mm is good for primer paint?

@peteshobbies5383

2 ай бұрын

Hi mate, good to hear you like the videos. Certainly, the Wider4L in 1.6 is good for primers, although the tip may be a bit small for higher build primers

Hello, thank you very much for your inforamative videos. I am currently looking for a Spray Gun and a silent compressor. The Wider1 or Wider1L should suit my needs. Can you tell me the minimum compressor requirements? According to the IWATA Homepage, the Wider1L 1.4 Gravity requires 200l/mins but I am not sure at which pressure. Is the volume referred to the "atomizin air pressure" (0,1 MPA). In this case my compressor needs to deliver 200l/min at 1bar for the Wider 1L. If my assumption is correct, the the regular Wider1 1.3 Gravity requires 225l/min at 2.4bar. This would mean that the Wider1 has a lot of higher needs regarding the compressor power. Am I right with my assumption? Thank you and best regards

@peteshobbies5383

6 ай бұрын

Hi Mario, It depends on the cap on the wider1 as to the amount of air it consumes. Normally, the air consumption quoted is the consumption of the gun at the recommended pressure. So you are right in your assumptions that the Wider1L will use slightly less air than the Wider1 with some caps. You also need to check the fluid output of the setup you are looking at because a gun may use a little more air, but it will spray a lot faster, so you will need less air overall for the same job, hope that helps

@marioweinberger9478

6 ай бұрын

Hello @@peteshobbies5383, thank you very much for the quick reply. You definetly helped me and to be honest, I really forgot to take the fluid output and speed into acount. Thank you!

@peteshobbies5383

6 ай бұрын

@marioweinberger9478 You're welcome buddy 👍

Hi Pete, great video's thankyou. I have an LPH80 1.0 and an Air Gunza 2.0. I have a 50 litre compressor with 8.4cfm F.A.D. I see myself painting more motorcycle fairings and tanks and the lph80 seems a bit too small, especially for acrylic while the Gunza is more for high build primer etc. I may also spray lacquer for woodworking projects. I don't have much space and so overspray is an issue. Would you recommend the wider 1L or the Kiwami3 1.4WB as the overall more flexible/better choice for my use/situation? Or the older LPH300 1.4? I am an occasional painter at best so don't want to invest in another gun after this one. Thanks so much. Cheers, Dom

@peteshobbies5383

7 ай бұрын

Hi Dom, The LPH80 is a great gun but can be a bit slow for bigger things. It's also very economical on air, runs at a low pressure, which gives low overspray, as you will know. There are a lot of alternatives, the Kiwami3 wb is very good and you should have enough air but you will notice a big difference in overspray. The Wider 1 1.4 runs at a very low pressure, same as the LPH80 from memory, so it also has low overspray. It should also be ok with your air supply. It's still rather slow but obviously faster than the LPH80. If overspray is a major concern, then I would go with the Wider1L

@domd2304

7 ай бұрын

@@peteshobbies5383 Thanks Pete, much appreciated. So you think the Kiwami3 wb would be preferable for motorbike fairings/tanks to the Wider1L, aside from the overspray? I don't want to take a half-step up from the LPH80 and then feel I should have gone a full step so to speak. Would the Wider1L be limiting in any way vs the Kiwami3? I predict I may be in analysis paralysis for a little while between these two haha. Would you go with a 1.2 if choosing the Wider1L? Interesting that the Kiwami3 wb uses more air than the older W300 wb (190l/min vs 230l/min). Thanks again.

@peteshobbies5383

7 ай бұрын

@domd2304 I think Iwata are just being more truthful with the Kiwami3, as far as I can see, they use the same, and it's definitely more than 190lm, the caps, apart from the bezel are the same. If you don't mind the higher pressure and overspray of the Kiwami3 then that's the one to go for, I find it doesn't quite like full fluid, it seems to overwhelm it a little so just back it off a little and it performs like a W300WB which is excellent. The LPH300 is also excellent and runs at a low pressure. It uses a little more air than the Kiwami 3 and is a little slower, like the Wider1L, I'm guessing because it has a 4 split tip as opposed to a 3 split which tends to speed them up a bit

@domd2304

7 ай бұрын

@@peteshobbies5383 thanks again. So basically it sounds like all are very similar? Lph300, Kiwami3 or Wider1L. The LPH300 1.4 on paper has highest air consumption (240 vs 230 vs 200), middle paint volume (90 vs 130 vs 80), and pattern width (250mm vs 265mm vs 200mm). If there are no notable differences in atomisation quality or physical quality, then I guess I can't go wrong with any? LPH300 144lV is the oldest design but maybe still holds up? It's the most expensive too, although all three are within 10%. Guess i'll just flip a three sided coin haha. Thank you so much mate.

@peteshobbies5383

7 ай бұрын

@domd2304 You're right in that you can't go wrong with any of them. I only got my LPH300 7 months ago, and I really like it, but there's so little between them, to be honest. Certainly, all are faster than the LPH80 Cheers mate 👍

Hi Pete, off topic here but does the pro lite cup fit the DV1? Would like to get one of those 100ml cups for my DV1. Thank you and great video BTW !

@peteshobbies5383

2 жыл бұрын

Hi David, yes, exactly the same

@davidray4655

2 жыл бұрын

@@peteshobbies5383 love ya Pete. Your always there with the answer👊

@peteshobbies5383

2 жыл бұрын

I try mate 👍

How’s this version compare to the Wider 4 L? I’m assuming the 4 is an upgraded version

@peteshobbies5383

Жыл бұрын

Hi buddy, The Wider4L is a full-size gun. This is a midi gun, so they are competing in a different field, really

@chukkaskate

Жыл бұрын

@@peteshobbies5383 Thanks mate. I went ahead an got one 👍. Should be a great little gun

@peteshobbies5383

Жыл бұрын

They are, don't think you'll be disappointed, not a fast gun but fine atomisation, which is what matters if you're after a good finish off the gun 👍

Hi Pete, how do you think this one compared to kiwami 1(for clearcoat)&kiwami rt(for basecoat)?

@peteshobbies5383

Жыл бұрын

Hi mate, this one is good because of its low pressure, low overspray, and fine atomisation. The other Kiwami 1 variations are different in that they are conventional, so higher pressure, standard tip, they are as good as each other, they just go about it in different ways

Hi Pete, do you or could you recommend someone to paint tank and fairings on a 94 zzr600 ,also how much roughly would it cost, just basic paint job but good materials

@peteshobbies5383

2 жыл бұрын

Hi buddy, any paint shop should be able to paint them for you, it depends where you are as to costs but most charge more for bike stuff because its more involved, then there's the decals which can be expensive, then it depends on the colours, the more there are the more expensive it would be, often 2, 3 or 4 colour fairings are in fact one colour with decals making up the other colours so they can paint those colours instead of decals but it very time consuming so is expensive, it certainly won't be cheap. If you want it all one colour without decals it would be much cheaper obviously, not sure that's been much help

@mjs924

2 жыл бұрын

@@peteshobbies5383 thanks for getting back to me, very helpful, think I'm better getting new fairings and have the tank painted to match, thanks again 👍

@peteshobbies5383

2 жыл бұрын

Yes, that's often the case, good used if you can get them or new, they are expensive but so is doing all the work so often better to just replace them, tanks, as you say are different as they are expensive and normally involve less work so are cheaper to get done

What's it like compared to a w300 wb

@peteshobbies5383

2 жыл бұрын

That's a very good question, it's very similar in it's delivery with low pressure and fine atomisation, I would find it hard to split them, the W300WB is more mainstream because of its centre cup but no clear winner

@danielsguitars1659

2 жыл бұрын

@@peteshobbies5383 Thanks, I bought a w300 wb and it's lovely for doing my nitro lacquer, the overspray difference is massive compared to my drvilbiss sri, I like my iwatas.

@peteshobbies5383

2 жыл бұрын

The W300WB is an excellent spraygun as you will know, gives a great finish 👍

Hi Pete, another great review. Must admit your a bad influence as I’m now leaning more towards the side-cup set up and the Meiji spray guns. Just out of curiosity what is cfm consumption for the Wider1L 1.4 and I’m assuming you purchased it from Paintingtool_Japan?. .. Thanking you, Sal.

@peteshobbies5383

2 жыл бұрын

Hi Sal, the Wider1L 1.4 according to Iwata uses 7.1cfm, I didn't get this one from paintingtooljapan, I bought it used, but unused if that make sense, it was the same chap that i got another 2 side cup Iwatas from on ebay in the UK, real bargains, you are right, most of my Iwatas are from paintingtooljapan who have been really good, also got my Meiji regulator from them which is brilliant . Have you got any side cup guns? , I really don't notice a difference except the side cups are not as tall as the centre cups, otherwise i don't notice it

@SaltyC-v2k

2 жыл бұрын

@@peteshobbies5383 Hi Pete, yes I've got the LPH50 plus 2 x ANI 160Q's and just placed an order for the Meiji 1.2 finer spot repair gun. Also looking at the w50. I'm a mobile SMART repair technician and I actually do SMART/alloy wheel repairs and not the whole side of a car on a drive way if you know what I mean..!!. These guns are ideal for this type of work but I'm particularly interested in the Wider1L because of the low overspray... Really do appreciate your videos and genuine reviews Pete and looking forward to the next one.... Cheer... Sal.

@peteshobbies5383

2 жыл бұрын

😂🤣, sounds like you've got the side cup bug 🤗 , what you will get from the Wider1L as well as low overspray is more fluid delivery if it's the 1.4 so better for the [relatively] larger bits you do as well as clear application in the warmer weather so definitely a place for it i would say, think i said i would suggest the 1.4 as the best overall, I haven't used a 1.6 or a 1.2 but think the 1.6 would be too much with it's higher pressure and the 1.2 that probably wouldn't flow enough material to make it different to the gun's you have, let me know how you get on as I'm always interested to hear and it helps me point people in the right direction when they ask, cheers mate 👍

@SaltyC-v2k

2 жыл бұрын

@@peteshobbies5383 will do Pete... 👍👍👍

@SaltyC-v2k

2 жыл бұрын

Hi Pete, I’ve got Gentilin C330/24 Air Compressor for my mobile work. It’s a 24ltr compressor which allows continuous usage with no down time…fantastic little machine. F.A.D: 330 l/min (11.65 CFM) Air delivery: 5 bar, 200 L / min (7.06 CFM) Haven’t purchased the gun yet but I’m hoping it’ll be compatible with the specs of this compressor…your thoughts?

Ani f160 vs wider 4 who wins ?

@peteshobbies5383

2 жыл бұрын

Hi Mark, probably the Wider4 but it is much more expensive normally

😍😍😍😍😍

@peteshobbies5383

2 жыл бұрын

Thanks buddy 👍, are you still on vacation?

@vehiclesprayerssociety

2 жыл бұрын

@@peteshobbies5383 you're always very most welcome Buddy 😍 I'm here in Ghana back to work.

@peteshobbies5383

2 жыл бұрын

Oh well, hope you enjoyed your holidays back home 👍

@vehiclesprayerssociety

2 жыл бұрын

@@peteshobbies5383 thanks Buddy.😍😍😍

@vehiclesprayerssociety

2 жыл бұрын

@@peteshobbies5383 thanks Buddy 😍😍😍

I use it to spray whiskey/wine/gin with soy-sauce/worcestershire-sauce onto steaks and barbeque roast

@peteshobbies5383

10 ай бұрын

Hi mate, well, I never heard of that one before 😁