Adjusting Points and Ignition Timing - Honda CG125

Тәжірибелік нұсқаулар және стиль

In this video I replace the contact breaker (points) on a 1990 Honda CG125. I will also show you how to adjust the points gap and ignition timing.
Affiliate links:
Flywheel removal tool: amzn.to/41QrxbV
Honda cg125 contact breaker: ebay.us/M00b3S
WD40: amzn.to/3vpVDqu
3-IN-1 OIL: amzn.to/3H8zY8F
Disclaimer: Please carry out this job at your own risk. I don't accept any responsibility for damage or injury caused by following this video. It is meant as a guide only. Stay safe and be sure to wear suitable PPE where necessary.

Пікірлер: 14

  • @pdpcycling248
    @pdpcycling2485 ай бұрын

    Good job! This brings back some good memories when I had a JX110 and converted it into a CG125 ;) Not sure if a original CG125 has 5 or 4 speed drivetrain, but what I did in the past was that I took the drivetrain from GL100 and swapped to my JX110. Then I oversized the cylinder bore to that of 125 cc and using the Wing 125 piston kit. Anyway, the contact point was a pain to keep up with, so I replaced it with DIY 2-units CDI system (like one in Suzuki RC110) and never had to change spark plug ever. Now I wish I could have that bike again!

  • @TurnersWorkshop97

    @TurnersWorkshop97

    5 ай бұрын

    Hey, thank you! Sounds like a great project you had :) Mine has a 5speed, not sure about the earlier models. I am considering a CDI upgrade in the future but I quite like the simplicity of points ignition, although it’s more maintenance 😁 did you find it made a noticeable difference when you upgraded?

  • @hookedonbass2640
    @hookedonbass26406 ай бұрын

    Nice job 👌🏼

  • @TurnersWorkshop97

    @TurnersWorkshop97

    5 ай бұрын

    Thanks man 😊🙏🏻

  • @user-xl6pn6xy9r
    @user-xl6pn6xy9r5 ай бұрын

    Thanks 😊!

  • @TurnersWorkshop97

    @TurnersWorkshop97

    5 ай бұрын

    No problem 😊

  • @user-xl6pn6xy9r

    @user-xl6pn6xy9r

    5 ай бұрын

    This is perhaps one the best videos on contact breaker ( Ignition system) on utube. Can you do more videos on the Honda CG on how to restore and maintain one.

  • @lakshithalucky99
    @lakshithalucky994 ай бұрын

    Thanks

  • @rangerbalatico2484
    @rangerbalatico24845 ай бұрын

    Hi boss I have a motorcycle Honda tmx 155 contact point model,, Can I ask,,what is the good resistance of primary stator coil?...of that motor check 125.... Maybe I can compare to my motor primary stator coil resistant,,

  • @rangerbalatico2484
    @rangerbalatico24845 ай бұрын

    Honda cg 125 primary coil resistance reading plss😊...

  • @gordyl9247
    @gordyl92473 ай бұрын

    Have you considered converting to a CDI system ?

  • @TurnersWorkshop97

    @TurnersWorkshop97

    3 ай бұрын

    I have indeed, might make a video about it soon if I can find the parts I’m looking for 😊

  • @rangerbalatico2484
    @rangerbalatico24845 ай бұрын

    I doubt my primary stator coil is broken... Because, when the engine is hot the engine shut down,, and hard to start again...

  • @TurnersWorkshop97

    @TurnersWorkshop97

    5 ай бұрын

    I would say that the primary coil is ok as the bike starts. You can check the voltage output when the bike is running and it should read around 6v to the ignition coil. I would do the basics, serving, valve clearances and ignition timing and see how you get on after that 👍🏼

Келесі