Abaqus CAE: How to model high deformation twisting problem using Abaqus CAE and Explicit Solver!!
Dear Abaqus Users, New Video on how to handle the high twisting deformation problem!!
Жүктеу.....
Пікірлер: 35
@TomCro20228 жыл бұрын
Very nice video.......and big respect from Zagreb/Croatia!
@DucNguyen-sh5en7 жыл бұрын
Amazing. Thank you so much.
@phucphantu25998 жыл бұрын
I like your chanel. Thanks
@yahia19881008 жыл бұрын
Very useful video. Keep it up bro ...
@yuxinqi24678 жыл бұрын
Thanks, man.
@mohamedelmakkaouy95188 жыл бұрын
good work ...thanks
@rajjyotidas44448 жыл бұрын
Hello, Thanks for the video and it has been a great learning experience with your videos. Could you please tell me on how did you select the value of point mass/inertia for the rigid body and what is its importance on the output ? Raj
@yuxinchen19966 жыл бұрын
Thank you for so many useful videos! For the self-contact friction, how did you decide the friction coefficient to be 0.2? What does this coefficient mean?
@user-jd2eh2zq5h7 жыл бұрын
Thanks a lot
@dilipdevpalli50527 жыл бұрын
is there anyway if i want to perform same kind of analysis but instead of film want to use strand wires as 1D beam element. And if yes how i have to define contacts between 1D(strands) and 2D elements(mandrel)
@saiarjunar1948 жыл бұрын
Thanks :)
@dilipdevpalli50527 жыл бұрын
can you please tell me about why you have used -37mm value in 'Z' direction in displacement BC???
@flawns8 жыл бұрын
This shows twisting, can it model add/remove material to figure out the prevention of twisting forces? Drive shaft for example
@cesarsanabria75846 жыл бұрын
How do you change your result exponential values to regular numbers?
@spyfromsparta3 жыл бұрын
For those not getting any displacement in the results, please follow the below steps 1) Go to Interactions module-> create constraint - > MPC constraint 2) Tie fixed and movable ends with their respective reference points 3) Now run the job. You will still get a couple of warnings but will get the output. ( The job ran 1.5 hours for me !)
@binzhang98537 жыл бұрын
Hi, I have followed every step exactly in your video but ends up with no deformation at all. Can you please share your input file online? Thanks a lot!
@dilipdevpalli50527 жыл бұрын
Why you have given -37 mm in Z direction in displacement boundary condition.Only twisting is not sufficient?
@palashdas8234 ай бұрын
In dynamic explicit can total energy be negetive?
@Brunoo_Martins6 жыл бұрын
Can you send me the inp file? I did the same and it doesnt work for me
@soniaahmadi6756 жыл бұрын
can anyone tell me why in the "specify distance" in tie constraint we put 5???? the film and madrel has only 1 mm difference in diameter.
@abaqusacumen7397
6 жыл бұрын
Sonia, This is just to make sure that there is proper tie between master and slave. We can put distance more than 1mm. For example 1.1mm is also good enough.
@informationrapide47 жыл бұрын
Hi thank you! why the Mass iniertia it 1e-03 ?? what is the reason ?
@abaqusacumen7397
7 жыл бұрын
Abaqus explicit need mass matrix to solve the problem. Otherwise it gives error for inertia missing.
@informationrapide4
7 жыл бұрын
No. i have solved it without inertia. it work
@kalpeshswain9603
4 жыл бұрын
Bt what you did, it solved without inertia?
@pyrotalk7 жыл бұрын
I am in the same boat as Jason. I submitted data check and it sits there. Monitor doesnt show any errors, steps, etc.. I followed step by step..
@EmilSilva
7 жыл бұрын
I think its because he doesn't tie the reference point to the rigid mandrel..
@mohammadkassar28527 жыл бұрын
amazing i want someone help me to mack works by abaqus
Пікірлер: 35
Very nice video.......and big respect from Zagreb/Croatia!
Amazing. Thank you so much.
I like your chanel. Thanks
Very useful video. Keep it up bro ...
Thanks, man.
good work ...thanks
Hello, Thanks for the video and it has been a great learning experience with your videos. Could you please tell me on how did you select the value of point mass/inertia for the rigid body and what is its importance on the output ? Raj
Thank you for so many useful videos! For the self-contact friction, how did you decide the friction coefficient to be 0.2? What does this coefficient mean?
Thanks a lot
is there anyway if i want to perform same kind of analysis but instead of film want to use strand wires as 1D beam element. And if yes how i have to define contacts between 1D(strands) and 2D elements(mandrel)
Thanks :)
can you please tell me about why you have used -37mm value in 'Z' direction in displacement BC???
This shows twisting, can it model add/remove material to figure out the prevention of twisting forces? Drive shaft for example
How do you change your result exponential values to regular numbers?
For those not getting any displacement in the results, please follow the below steps 1) Go to Interactions module-> create constraint - > MPC constraint 2) Tie fixed and movable ends with their respective reference points 3) Now run the job. You will still get a couple of warnings but will get the output. ( The job ran 1.5 hours for me !)
Hi, I have followed every step exactly in your video but ends up with no deformation at all. Can you please share your input file online? Thanks a lot!
Why you have given -37 mm in Z direction in displacement boundary condition.Only twisting is not sufficient?
In dynamic explicit can total energy be negetive?
Can you send me the inp file? I did the same and it doesnt work for me
can anyone tell me why in the "specify distance" in tie constraint we put 5???? the film and madrel has only 1 mm difference in diameter.
@abaqusacumen7397
6 жыл бұрын
Sonia, This is just to make sure that there is proper tie between master and slave. We can put distance more than 1mm. For example 1.1mm is also good enough.
Hi thank you! why the Mass iniertia it 1e-03 ?? what is the reason ?
@abaqusacumen7397
7 жыл бұрын
Abaqus explicit need mass matrix to solve the problem. Otherwise it gives error for inertia missing.
@informationrapide4
7 жыл бұрын
No. i have solved it without inertia. it work
@kalpeshswain9603
4 жыл бұрын
Bt what you did, it solved without inertia?
I am in the same boat as Jason. I submitted data check and it sits there. Monitor doesnt show any errors, steps, etc.. I followed step by step..
@EmilSilva
7 жыл бұрын
I think its because he doesn't tie the reference point to the rigid mandrel..
amazing i want someone help me to mack works by abaqus
Why didn't he assigned element type?
AAAAAAAAAAAAAAAAAAAAAAAAAHHHHHHHHHHHHHHHHHH
CA NE MARCHE PAS !!!!