Excelente explicación, mi amigo. Te felicito, has aclarado muchas dudas que yo tenia. Muchas gracias.

Man those are some nice welds! Thank you for posting this great tutorial!

Excelente aplicación y resultado, muy bueno para practicar. Felicidades!!! Saludos desde México.

Just know that this is a "Cover Pass" technique and not meant for the "Root Pass" especially on a fillet. You need to use the Whip N' Pause, Inverted "T", Inverted "V" or Triangle rod manipulation to get any kind of root fusion since E6013 has low penetration characteristics. The "U", "W", or "Z" weaves are fine for uphill covers and stringers work equally well with a circle motion. Any other position requires you to stay on the leading edge of the puddle to keep the slag at bay. Like most stainless steel electrodes, E6013 requires some type of weave motion with a slightly longer arc length to blow the heavy slag back to make the puddle visible. The increased arc force also helps prevent wormholes too. Remember, E6013 is a slow deposition electrode hence you need to spend more time on the toes and go a little slower than E7018 😉

@vulcano911

8 ай бұрын

I envy to see those weld seams. I can't do anything like that

You are a excellent professor of welding....Good job🇦🇱

Thanks. Have to repair my trailer this week and that will involve some vertical welding. I don't have much experience as I only got a 1-night a week course some years ago.

Superb Information in the Beginning about Ampere and MM thickness of Rod Please Make Some Tutorials too so that we can Get Technical Knowledge Like this Which helps in Welding Works Thanks Once Again and God Bless You !! Superlike 👍👍

Thanks for your teaching ! It really helpful

I always understood that you should go low on amps when welding vertical up because the heat rises ahead of where you're welding. But 150 is nothing like low on amps. And it still looks really nice!

Thank you for teaching me such wonderful techniques for free

Excellent best vertical I’ve seen wish I could do the same

Si esto fuera moda, vos hacés alta costura. 👏👏👏👏👏

Incredible. Youre a smart guy. Thank you for sharing your knowledge and may God bless you more.

Thank you, I didn't think that 6013 could be used for vertical up. I had been using low amperage settings . A big thumbs up.

@tandemwings4733

2 жыл бұрын

Of course 6012 & 6013 can be used vertical up. UP - is the ONLY way to weld vertical. Down is only any good for cosmetics. With the exception of pipeliners of course, and that's an entirely different discussion.

@ZENERVOLTAGE

2 жыл бұрын

@@tandemwings4733 I'm glad you said that. Uphill for 3F position is the norm...and for any vertical. Not really is "secret trick of the trade" lol.

Obrigado por compartilhar seu conhecimento parabéns.

Браво чудесен урок!

You are very good! Thanks!

6013s look awesome!

Hi,watching from Romania, nice welding ✌️

Foarte bine aplicata in practica,meserie🦾🦾

You need to go up to get root penetration and then across as you are doing but with longer pauses at each side to avoid the slight undercut you are getting. If you break that weld, you will find low root penetration with some slag inclusion pockets

@falkirk8413

2 жыл бұрын

Especially with a 6013

@frunk6006

Жыл бұрын

100%

@alexdissieux5137

Жыл бұрын

And for the roots,I change my polarity (electrode negative)

You're the only welder I haven't judged on KZread so far 😂 beautiful work

Nice 👍 Assalamualaikum brother Metal thickness, Electrode and Amp please?

Muy buen video amigo gracias por tus buenos videos se aprende 👍👍👍👍

Buenos trucos amigo

Im new to welding and have a hard time figuring out the puddle distance ive been told roughly 1/16 or 1/32 of an inch away but thats about it. Is there more to it than that or do you also have to do additional steps to keep your puddle flat. (Mine rise like a mountain and finish like a bb size. ) any criticism or help is appreciated

Mais uma vez um belo vídeo 👏👏🇧🇷🇧🇷

@anilpatel1287

2 жыл бұрын

Panini n

We need more videos on this, it is very important for us, wherever we go, a test is taken about this.

Nice stick welding! 👍👍👍👍👍🔥🔥🔥🔥🔥

I try vertical up with 6013 low or high amp my weld doesn't look like this. Vertical down look very good

Super, l always struggle for verticals, ll do more practice. Excelente!

Thanks you videos tutorial next brother 👏👏👏💯👍

It's easy to weld thick metals. I would appreciate if you do the same job on thin metal...

Awesome work sir 👌

👍 genial mi amigo.me gustaría que hagas videos con soleras o ángulos de espesor finos que es para hacer trabajos de hobbies y es lo cuesta más para uno que está aprendiendo okey.gracias✌️

Excellent vertical welding bud,excellent !👍🏻

El movimiento ascendente en zig zag es lo de menos, lo mas importante es la potencia, el amperaje seleccionado para que el charco no se caiga.

thanks for the knowledge you share 👌👌

Kullandığın elektrot bazikmi yoksa rutilmi ?

Though good elburg for most aplicationd. Tour welde Souls be more flat right and more consultant. When going up i would hold your ro single slightly mor flat and work fromthe wrist more.

الله ينور يا باشا

Excelente aporte

thanks for sharing👌

En unos 100 años llegó a ese nivel, que genial soldadura

Pekne video som tiež zvarac bud zdravy pozdrav zo slovenska🇸🇰🇸🇰🇸🇰🇸🇰

Boa noite qual operagen que você usou para fazer essa soda.👍👍😔

Iron man : you're the best one!!! Congratulations from Romania!

Di bidang welder(las) yg paling penting skil (keahlian). Izin bertanya bos... Apakah di media yg tipis (0.7 mm,)apakah bisa di terap kaya zig zag nya bos?

Thank you for posting this great tutorial!

I use Vodex rods They have been available since my apprenticeship 1961 to 1967 ? 60 years ago where did the time go?

Great video, thank you

Eu sou a Yola Gosto muito dos vossos videos ,soldo a quase um ano mais tenho muita dificuldade de soldar vertical e 4f gostaria que me ajudacem

Thank you sir, good tips

I like this video. thanks

Hi very nice and professional 👌

that low penetration cant be 150A. Personaly i think you have used like 110A, or 100 for this welding.

@robylv5720

2 жыл бұрын

Came here to comment section, cause i saw the arc was low. And wantes to see who else thinks the same. That is 10mm steel plate, he is going up with about 90-110 max. 6013 3.2 is burning with big arc already with 125amps...

@tandemwings4733

2 жыл бұрын

@@robylv5720 I agree with the amps figures you mention. Welding machines are not consistent when it comes to indicating amp settings. If I ran 3.25's on 150 amps, I would be dealing with some serious edge undercutting. I run 3.25 - 6013 at around 115 amps for vertical up, using a Fronius Transpocket 1500.

Membantu saya dalam belajar tentang pengelasan vertikal..Terima kasih temanku

Esse manja e entendi do assunto já fui soldador conheço o bão e u ruim 👍👍nata 10

Mối hàn rất đẹp và cũng chắc cảm ơn chia sẻ cách hàn của bạn

en esta posicion deberias bajar la fuerza 20 %

Sure! Convex bead and uneven bead height will come with this technique

laying dimes , good, is this DC delder?

Espectacular 💪💪

joss tnan. posisi vertikal hsile koyo lasan bawah tangan👍👍

Hi to all, regards from Venezuela

Me e quedado sin palabras

Genial Bro. 😸👍, Saludos desde Cusco 🇵🇪🙋🏻‍♂️

แล้วแนวตั้ง7016เป็นอย่างไรครับ

Mình Xin được cảm ơn tác giả.bài chia sẻ rất hay và hữu ích.

Great! Thanks

The vertical T weld was one of my favourite position weld back in the day, this guy has done a good job nice one bro

@tandemwings4733

2 жыл бұрын

Hah. I just realised what a "vertical T" weld could be. That would be what we called a "vertical fillet". Does that look right to you?

@mikekahotea8148

2 жыл бұрын

@@tandemwings4733 yup that's right, over 35 years since I did those sort welding jobs back then

Qual a inversoura que vc está usando

Nice video brother. Subscribed

جزاك الله خيرا

Vertical acendente dá maior penetração, ótima para soldar chassi e estruturas que exigem maior responsabilidade.

Is weaving bad for penetration?

great video . (* in europe - milimeter = mm / mililiter = ml )

@tandemwings4733

2 жыл бұрын

In Australia - millimetre = mm / millilitre = ml.

Nicely 😊☺️❤️

What is the amperag(current) for vertical up

Great welding job

Hello👋🙋‍♂️ there... Amazing and very interesting video Good information and very helpful Do keep posting Warm regards and best👍💯 wishes The UnknownManCub 👍😎👨‍🏭

What brand of your welding machine

Merci beaucoup.

Muito boa dica ! Show !!

Verynice welding works

Rwanda ❤ good technician

Amazing 💪💪

Com 120-125 já perfura a peça e dá mordedura, com 150 é que não solda mesmo, no máximo que deve estar aí é 100 ampére.

@paulrodax2010

2 жыл бұрын

Esta soldando con electrodo de ⅛"

My favorate is vertical weld

هل سمك الحديد له دور في ضبط الأمبير

Excellent

Excellent. But for beginner , this way is not easy. They need alot of ptistise

how many volt amperes for vertical welding?

GOOG job👍

Pwede mo ba maipakita ang actual tulad ng may rotpass in vertical position bos

Ты металл 2 или 1.5 покажи как вертикально также сварить 🤣🤣🤣🤣 понторез

@user-wd2qf8wk3v

2 жыл бұрын

Все тоже самое. Только сверху вниз.

@paulznack2379

2 жыл бұрын

@@user-wd2qf8wk3v и шлак не сбивать😂 Сантиметр шлака, держит 10кг металла!

بيش الدوره عندك وشكد المده في مصر

stitch weld is ok whip TIG style is good too

Super up welding 🤟🤟

เยี่ยมเลยคับๆๆๆๆๆๆ