Terimakasih telah mengupload video tentang pengelasan SMAW akar 2G cap 7018 ini. Sangat berarti bagi saya. Salam hormat ⚘🙏

Pěkné, řekl bych od Profesionála. V kořenu místy "vruby", ale provařený, s dobrým převýšením... 🤘

@StepanGregor-no5zv

5 ай бұрын

Na základní kurz dobrý.

That first pass was impressive, Using a grinder is a no no, I don't think it would pass, But you certainly understand what you're doing, You've got your attack angle correct.

Pěkné, provařené od kořene. Pevnost 100%. Dobrá práce.

I welded and cut and bent both ways so many of these I get sick just watching you set this up. I had a box full of these test plates made up and had to weld them in every position. Predominately with 7018 but also 6010. I still have burn scares, laughing. Brought back old memories. Thank you

I've been melting electrodes since 1979 and I'm still learning, congratulations on the video and technical ability

@kennethcrowe300

Жыл бұрын

sloppy at best

@theouter_banks7260

Жыл бұрын

@@kennethcrowe300 and at worst?

@joebly5641

Жыл бұрын

@@kennethcrowe300 who cares welding isn’t a art competition it’s about getting shit done that works. Everything isn’t a pissing contest . I’m sure there are welders that make u look greener then the grass in spring . Just because you hate yourself so much doesn’t mean you gotta bring others down

@shaun-o4360

Жыл бұрын

​​​@@joebly5641 you're right it isn't an art it is a trade and in a trade there is this thing called VISUAL INSPECTION If a weld is shit then it looks like shit aslong as your looking for the right thing unless you're working on playgrounds or hand rails for the middle of nowhere or welds that don't really matter and are just there to stick some random shit together for a quick gig then you would be correct...but for this shit it's quite important I would fail this plate just because of the sheer amount of undercut plus the hollows I saw on the arc shot Something I have to check off on a sheet everyday at work is uniform weld profile uniform length and width of weld bead.

@robertlee4809

6 ай бұрын

​@@joebly5641Are you a welder? If not, then shut the hell up🙄😂there is such a thing as visual inspection. 99% of the time, if that weld looks like shit, it probably is shit. After 40+ years of welding in steel mills and nuclear power plants, I have seen MUCH. And shitty, subpar welding is not acceptable where I'm from.

I'm new Lerner, from Bangladesh. Ur video is so helpful. Please make 1G and 4 pass video

Taí! Gostei da simplicidade na montagem do teste... Mais explicado que isso não existe! 👏👏👏

A से Z तक आधुनिक गेट और विकेट। काटना, वेल्डिंग करना, पीसना। मेरे अनुभव से सलाह। लेखन :6 kzread.info/dash/bejne/gqWayqqPpJnVZZc.html Modern gate and wicket from A to Z. Cutting, welding, grinding. Advice from my experience. Writings : kzread.info/dash/bejne/gqWayqqPpJnVZZc.html

This man knows what he is doing. Depending upon the place you're working. I was always told no cutting wheels on a weld test. Only wire brush wheels.

@angertone213

Ай бұрын

You can use tools, you just end up forfeiting some certs that require you use NO tools.

всё это красиво на стендах , я варю в насосной турбы 300/400 диаметром , до 50 атм ! там иной раз между трубами даже с зеркалом не подлезть ! а операции делать категорически запрещено , тренировался на обрезках труб варить в слепую на слух , долго мучался но пошло ! стаж 30 лет ВСЕМ ДОБРА

@user-yp1bd4sl6f

Жыл бұрын

Сварка - это жизнь и пока есть тепло, вода этого не замечают. Сделайте видео ваших примеров сварочных прийомов для народа.

@raymundoanastacio2257

4 ай бұрын

.

Da , meseriaș adevărat. Felicitări.

Sy pernah belajar las seprti yg ada dlm video ini. Setahu sy untuk tembusan awal menggunakan kawat merah. Untuk keping baru kita menggunakan 7018 LH70. Waktu itu kota di bending menggunakan hidraulik press hingga membentuk U. Jika undrrcut dipastikan pengelasan akan patah atau retak.

I'm Anele Mgqibela from Cape Town in South Africa I'm a welding student I've learn a lot thanks bro.

@zukispur5493

Жыл бұрын

Anele. When practicing in your welding bay don't always have the practice peices on your bench. Weld some underneath the bench above the bench switching hands. Awkward positions. You'll thank me one day 🌚 oh and loosen your grip on the electrode holder.

@miguelangelmichel6501

Жыл бұрын

mucha socabadura

Interesting video I'm a student from Cameroon...i do study in advance vocational training center and i will like to learn more from you sir

Nice job for a learner. Try half the gap with a 7016. Don't flick back and forth your chucking metal away. Keep the arc short and watch for the arc flame just licking through. If it gets too hot slow up and shorten the arc to cool it down or vice versa . This applies to all positions and trains the eye to watch the pool. First ten thousand bots are the hardest.

@jewellerydesignerartists9353

Жыл бұрын

Hello sir ❤️ have a great day

@TVTruther

Жыл бұрын

why don't you make a video showing how it's done? anyone can say do this or that...

@timstone5112

Жыл бұрын

Retired two years ago having welded power station tube walls and steam turbine pipework,gas and oil pipelines, gas compressor stations, and hospital size boiler rooms. Being an old git I'm crap at videos and besides haven't got a piece of 6" 5LB in the garage so l can't help you there, sorry. You will come across someone somewhere that can knock six to ten of these out in a day to radiographic standards. I learnt from an older guy at work well after finishing a five year apprenticeship . Good luck.

@TVTruther

Жыл бұрын

@@timstone5112 so you can easily show how it's done on video.. do it... any clown can post I did this or that.. so what

@chadmoyer1453

Жыл бұрын

@@TVTruther we understand your point but tbh I don't see where this man disrespected or said anything wrong about the video. In fact, he tried to help.

Boa noite iron essa é a segunda vez que eu me escrevi no seu canal parabéns pelo seu trabalho excelente amigo sucesso para você

It is very interesting to show the angle of the rod (side view) while welding: sometimes your rod is almost perfectly horizontal while other passes you aim much more up. Understanding the perfect angle in relation of the plate is i think key of making a perfect weld. Thanks!!

@chongraxesh1

Жыл бұрын

its 90• degree

Root pass hot pass was 🔥you've made it like it is ez.

Keliatannya sangat mudah 😁tapi saya rasa menjadi tukang las itu tidak gampang 🙏skil anda luar biasa 🙏🙏saya salut dengan itu 👏👏👏

I took that course in 1991, and I remember that in the 45° x 1/8 bevel, the penetration electrode was 6010, in negative polarity. Yo realice ese curso en 1991, y recuerdo que en el bisel a 45° x 1/8, el electrodo de penetración era el 6010, en polaridad negativa.

Excelente trabajo saludos desde Ecuador bendiciones

The whole point of welding is to melt both metals equally and to drag the rod if it is horizontal position, if you weld verticals than some rods like 6013 are perfect for vertical up, but do not try vertical down with that electrode, if you weld with 7018 than your arc needs to be very short, I mean you need to melt both pieces with same rhythm and move electrode, after some time you will get experience to make it routine.

@user-qs5so6nv9e

Жыл бұрын

Рррррррииириирррриррикбирррирррр

@1113562

Жыл бұрын

​@@user-qs5so6nv9e 9

@1113562

Жыл бұрын

I would not do circular motion for the root. Just a drag with a short arc length. As long as there is weld protrusion at the rear. To me there was too much protrusion after the first pass. Good idea about tacking blocks on the ends to maintain the gap while welding across the width.

@zukispur5493

Жыл бұрын

You can drag or pull the rod as long as the slag pool is behind the molten metal pool.

Сварочный шов нагрузил на 300%. Зазор между деталями слишком велик!

@simbiozful

Жыл бұрын

В данном случае, показан способ сваривания, если такой зазор, попадётся

Хорошие электроды.На вид-отлично заварил! Fine rodes, good job visually 💪

@ismaelantoniodasilva4647

Жыл бұрын

👏👏👏👏

@gatogordo2597

Жыл бұрын

Кстати да. Сразу видно качество электрода. Шлак просто одной- двумя чешуйками отслаивается

@user-ml6rk4tl1p

Жыл бұрын

Здравствуйте! Хотел спросить можно ли варить 1 см материала любом электродам. Или есть разница??? Мне дали 4 электрод сварка очень слабый когда варю постоянно прелипаеться к металлу. Начальник говорит это в проекте так должен

@gatogordo2597

Жыл бұрын

@@user-ml6rk4tl1pэлектроды просуши, ток добавь. Пробуй в два шва варить. Электрод 4 для металла 4-6 мм, ток 120-200. Сантиметровый металл варится электродом 5-6 током 220-320. Либо токами слабее и электродами тоньше, но в три-четыре прохода

@user-ml6rk4tl1p

Жыл бұрын

@@gatogordo2597 спасибо за ответ сделаю!!!!

Compare 1:30 to 2:49 and you will see there was something changed about the video sequence. At 2:49, the wing added to the right side doesn't have a hand grinder groove cut in it. You can tell at the very end of the first pass, the root, he was panicking because it was getting hot and about to blow out. I think there was multiple attempts at this root pass on different plates. Unless someone dictated such a large gap for the spacing on the root, I don't see the point. Cut landings on the plate edges and use less gap for spacing. A few extra amps and push the rod forward instead of dragging the root and you could easily watch it cut through without so much flipping back and forth and pushing so much puddle through the backside of the plate. Maybe the plates were prepared for him and that's what he had to use along with the required spacing? Who knows? No explanation given before video. It could be done easier as far as the root pass went. None the less, informative video.

@whamburger4576

Жыл бұрын

Your comment made me laugh. My first thought was why an 1/8 gap with no land on the bevel? You are just asking for an unwieldy size keyhole 😅. I'm with you, tighten the gap, grind that knife edge of a bevel a nice land and kick up the amps and punch through. Should be easier to maintain the keyhole and get all the way across with a single electrode.

@bojack2740

11 ай бұрын

Busted😂

@Obijuuankenobi

8 ай бұрын

.57 second tack becomes a weld ?

@spokes318

4 ай бұрын

​@@whamburger4576look again. That gap he set appeared to a covered smaw electrode. At the very least it was 3/16, looked more like it was approaching 1/4 inch.

@misplacedcaper9662

2 сағат бұрын

Material definitely changed. What he started with isn't the same as what he finished with. Guessing he blew the shit out of the first one with such a huge gap with no land and started over. Why suggest pushing the rod instead of dragging? Risk of slag inclusions...

Muy buena la presentación aunque note que eran probetas diferentes , mi pregunta es cuántas probetas se hicieron antes de subirla a presentar

Good penetration good appearance w/out undercut and porosity reinforcement also accepted nice job tanks you!

@user-dt9gg1py3e

4 ай бұрын

Очень хорошо, называется "маруськин поясок" мне нравилось варить горизонтали, хорошо заварено.

I took the all position test in 1970 and worked for Marion Power Shovel .

بهتر بود برای فاز ریشه از 6010 استفاده میکردین راحتتر بود و واسه همین منظور طراحی شده ولی در کل عالی بود فقط یه نکته که 7018 باید رطوبت زدایی بشه و محل جوش باید گرم بشه تا ترک برنداره

As working student I just wanna keen about welding at the beggining when I found this I'm so interested I have some guild thank you I'm just learning of welding

EXCELENTE VIDEO¡¡ SALUDOS Y GRACIAS POR COMPARTIR¡¡

@jewellerydesignerartists9353

Жыл бұрын

Hello sir ❤️ have a great day

the essence of welding connects two materials into one

Saran aja nih bang kalo bikin tutorial tu minimal kasi tau ampernya jadi kita sebagai penonton juga menambah wawasan.

Во-первых корень безобразный очень крупный Валик обратный громко тоже подрез идёт и последний валик тоже подрез потому что углом назад ввёл надо углом вперёд последний облицовочный вести Валик неправильное заполнение облицовочного шва последнего изначально очень крупный зазор и большое притупление можно было меньше притупления сделать и меньше зазор проплавление Аккуратнее будет меньше надо будет заполнять Это на будущее угол разделки будет меньше потому что из-за зазора и всё проплавится надо правильно собирать детали

Probably a36 x 3/8 in thk plates.. cellulous root and lo hi capping rods... nice strings.. we use 6010/7016 combo here.. 🙏🙏🙏

Very cool. I wish good luck to the author of the channel.

Root pass had porosity. Cap was undercut. Grinder didn't have a guard.

@samuelswearingen8435

Жыл бұрын

He's welds would not have passed a bend test. I don't know how people think they can get all of the slag out without using at least a brush.

I did this schitt most of my life. I will tell you, I don’t miss it even a tiny bit. It’s a hard, nasty, hot, thankless job. Not to mention hazardous in a variety of ways. From burns to slag getting in your ear. Why anyone would want to do this for a living is beyond me. Haven’t picked up a welding rod in years and couldn’t be happier.

Gênio!👏👏👏👏👏

Cool video. Seems like you did two runs. End plate was cut with the angle grinder but not after checking to stick number teo

Надо срезать вводные планки по бокам. Показать сварной шов по срезу.

@jewellerydesignerartists9353

Жыл бұрын

Hello sir ❤️ have a great day

@user-gz8nf1lo8g

Жыл бұрын

Там у него на корне поры , даже на камере видно

@user-ie1ie3jk4t

6 ай бұрын

​@@user-gz8nf1lo8g ну дак кто же на корне вперед-назад размазывает, и зазор там чет конячий был.

@John_Smith_777

Ай бұрын

На просвет не пойдет. Для ученика еще более менее

Pengelasan sampai akar menambah kekuatan benda kerja..ini keren temanku👍👍

pushed into the top edge to much rather than letting the rod consume and fill it, which i think caused the undercut. i'm still in welding school, but i recently fixed my undercut issue for the cap passes on V-groove joints by watching how my instructor has literally 0 undercut on his cap.

@rainsrapidly

6 ай бұрын

You're right... top cover pass needs more upward angle & push in to fill over the undercut

Горизонт, вертикал, потолок - только опыт приводит к хорошим результатам.

Terima kasi bnyak titorial las 2g nya sir👍👍👍🤝🇮🇩

Có vẻ như cái phôi đầu video đã bị hàn hỏng và đc thay thế bằng phôi mới. Khe hở chỉ để ở tầm 2,5~3,2 thôi. Khe hở ở điểm xuất phát nên bé hơn so với điểm kết thúc vì càng hàn thì nó sẽ càng bị kéo sát vào. Mặt phẳng 2 phôi nên bẻ ngửa 5 độ

Хорошая работа , только вот диск на балгарине поменять на ежа было вообще идеально ,ну как тут не при...😂 на ультразвук на наличие трещин

Muy bien amigo, solo que, creo que fue mucha abertura al principio para el fondeo, con 3/32 de abertura es mas que suficiente y con eso queda una bonita vista por atras.

@plazamarreservations3186

5 ай бұрын

soldó de mas y se veia cochinon

@boricuaarecibo9259

2 ай бұрын

Soy Nuevo en este oficio para mi no se ve malo

Desbordarles el materia superior para que por la gravedad se deposite en la parte inferior . Y darles primero con selulosico . Esa es la formas correctas. Del soldador . Saludos desde lo lejos .🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷

The gap is wider than I prefer, but to each their own. There was a lot of porosity in your root pass, but I didn't notice it nearly as much in the fill or cap. All in all, I think it would pass a bend test. 👍

@volatile100

Жыл бұрын

Wouldn't even pass visual inspection. There's so much undercut on the last cap pass, which he wouldn't even need to do if he didn't grind the hell out of it, which would also fail you at most places, since they typically only let you grind the root to feather, and the rest will be wire wheel only. The probable porosity and slag inclusion from pure chipping and not any brushing could potentially crack it during a test. That's assuming that they even let you go to bend it. But given that no country with safety standards uses Arabic even as a third language, it would probably be fine even if it did crack.

@ArkansasUnderground

Жыл бұрын

@@volatile100 yea I didn't even notice the undercut on the top cap weld. That'd be a no go.

@TrillMurray

Жыл бұрын

@@volatile100what do you think caused it to undercut?

@volatile100

Жыл бұрын

@Trill Murray Too hot and having too little angle are most likely causes for it to happen. In this case it's probably the heat, since bead profile isn't drooping down like it would with bad angle. Turning down the amps or letting the plate cool would fix it.

@TrillMurray

Жыл бұрын

@@volatile100 thank you! I really appreciate it.

para mi parecer y despues de mas de 30 años soldando eso no se suelda asi, en primero lugar esta terminantemente prohibido la soldadura con electrodo rutilo ( 6013 ) lo normal es soldar con electrodo basico 7018, y esa forma de soldar estoy totalmente convencido que que hay poro en la raiz, en la posicion de soldeo en 2G se tiene que hacer como una especie de C con la parte superior mas larga que la inferior y sin avanzar mas que el material de aporte, este tipo de soldeo se podria realizar para uniones que no tengan demasiada importancia, como puede ser una barandilla, en el peinado has medito la amoladora y has hecgo un corte muy fino en el relleno de la pieza, tienes mucho riesgo por no afirmar por completo de falta de fusion entre pasadas, yo te puedo garantizar que esa soldadura no es viable para radiografia. deberias si es que quieres enseñar a la genta a soldar ese tipo de posiciones hacerlo bien , esa soldadura no es validad bajo ningun concepto

@lianqishi

11 ай бұрын

正解，6.28秒就是一个严重错误，这板子RT根本不可能过！

Great job. Thanks

Mais qual seria a amperagem que está usando?

Hello 🤩 thanks 😍....but just a question,why 6013 for the roots?

Mantap om 😁 tetap semangat 💪😊

I don't know why I'm not seeing people calling this a fake. I've seen different sets of plates in this video and anyone who has ever welded an open root joint like that knows that a 6013 would not fill that huge root opening like that.

I was taught to grind the bevel first at least 1-2mm to create root face so it would be easier for root pass.

Excelente 👌

Bravo, Majstore.....

4G Welding Tips And Trick Bro Am India Sarver Watching Yoer video😮😮

Quais amperagem? Passe 1 Passe 2 Passe 3 e por diante? Agente que tá aprendendo quer saber o detalhes . Grande trabalho aí 🎉 parabéns.

@alejandrocanizares3045

11 ай бұрын

1 74 Ampere 2 90 Ampere y 3 115-120 Ampere

Great job👍👍👍👍👍👍👍👍👍

Very nice finished weld. Why no backing for the root pass? Although I never used it, they make a tape you can use for this. The root gap also seemed a bit excessive but I am not certain. I design heavy steel structures and refer to AWS D1.1 for preapproved welds for guidance. Anyhow, nice looking weld.

@methodicalvxp9265

9 ай бұрын

this is open root that's why there's no backing

뒷쪽은 용접을 하는 장면이 안나왔었는데 어떻게 된거죠?

In a nuclear power plant welding test. A grinder is only allowed when cleaning mill scale on your test plates.

Gambar pertama anda menerangkan proses pengelasan maju mundur.... Tapi saya melihat ada kegagalan di pola maju mundur sehingga mengakibatkan pembesaran jarak antara besi pada lasan... Dan anda berganti pola dengan pola berputar naik turun... Dan itu berhasil

Подрез по верху, обратный валик желает лучшего.

Luar biasa mantab penjelasannya sobat👍👍👍

Ça semble facile , mais c'est pas le cas 👍👍 je suis impressionné , bravo 👍😊

Great lesson master😊

Maşallah, good job.

Ferramenta amolada, fogo alto!

Вы точно сварщик?)) В корне поры!

The last weld seams I saw the porosity , perhaps your electrode was not at the ideal temperature ?Because if it were a welding test that board is rejected...

A little more juice for good fusion, slag and crevice burnout, and use multiple stringer beads instead of weaving the fill.

Qual a operarem que você está fazendo a solda?

My sadistic weld instructor had us use 6010 for our certification welds. While the day class got to use 7018. He told us we’d thank him when it came time to get a job because we’d be better welders than the 7018 guys.

Info yg bermanfaat sekali kawanku 🙏🏼🙏🏼

Lovely Root weld! well done, but please never clean slag off with cutting disk ! just chip it off with chipping hammer, bad practice really, regards.

Gostei da solda aprendi mais um pouco

Mantap bg metodenya mudah di pahami

EL PROTECTOR DE LA AMOLADORA. RECORDAR MEDIDAS DE SEGURIDAD MINIMAS

Première passe électrode basique au moins. Bourrage et finition électrode au plus. Tenir l'électrode en arcs courts sinon votre soudure sera un champ de souflures sphériodales. D'ailleurs la première passe est toujours blanchie pour contrôler une bonne compacité du métal déposé.

Saludos desde cali valle del cauca Colombia, quiero agradecerle por el video te comento, La raíz se debe hacer con 6010 o 6011 para la penetracion de la raíz , luego se hace el relleno con 7018 y se procede a hacer la presentación con 7018 con cordones intercalados de abajo hacia arriba me parece que el proceso está mal de inicio ya que se uso un procedimiento inadecuado

@leimanduran2688

10 ай бұрын

Correcto eso no sirve pa un carajo 😂😂

Parabéns Meu companheiro

Ever use 6011 or 6010 for root ? I always see you using 6013

подрезов бы не было тогда супер

This welding peace I love this work.

Perfect weld.👏👏👏

жаксы ислеген усындай кылып ислеу керек рахмет

The world look good but there's one thing I know that heats up too high something's off because on a pretty Chevy 18 weld your flux should curl up behind and come off by itself as your welding

Ur work is appreciable bt if u took the plat flat it will be more stonger and easier to weld it.

@samrowe2889

Жыл бұрын

This is a dumb comment please think about what u said

Mantap....matur suwun ilmunya

En mi época no permitían hacer guía con el disco solo grata

Hola qtal se te ve un buen soldador el problema para que uno entiende bien tiene explicar la la posición de la mano y el amperaje gracias

Bạn hàn rất đẹp ..❤❤❤

Mmm no creo que sea necesario hacer el movimiento de oscilación con la soldadura 7018. Solamente se apoya la varilla y avanzas. bueno en fin cada uno lo hace como desee. 👍👍👍

@KyMJose

Жыл бұрын

noté que al principio del rellenado si hacía el movimiento oscilatorio, luego ya no lo hacia, iba recto el recorrido, cual seria la razón, no soy un experto en soldadura , será por que las placas estaban de forma vertical?????

Very nice job sir

I wonder what his settings are on the welding machine?