Ya I would like that

I use the TransGo 700-PKH (5500+ rpm) and the spring that comes with it you can't squeeze it by hand.

Just found you're channel already subscribed..killer personality🤟🏼😎👊🏻

@expressautotransmissiondav4207

2 жыл бұрын

Thanks we have a good time with it for sure

@dalehall2993

2 жыл бұрын

@@expressautotransmissiondav4207 Are you in baxter springs KS? If you are,im about 45min from al rosa vila where the biggest tragedy in panteras history took place..

@expressautotransmissiondav4207

2 жыл бұрын

We are in Baxter springs ks you'll have to stop by sometime

@dalehall2993

2 жыл бұрын

@@expressautotransmissiondav4207 For sure..alright,alright,alright.(dazed&confused)

Great video, when you machined the pump half, wouldn't that change the clearances for the vanes? Should you machine the otehr half also?

How much do you charge to turn faces?

What do you set your clearance on your clutch packs 3-4, forward, reverse input drum....ect?

how much do you charge to resurface the pump faces? thanks

A video of you setting up the pump on the lathe and doing the measurements would be nice.

Wanted to ask about the lathe you use to perform the machine work. Would you be willing to share the specs on that machine?

Where do you get a pump kit

Got a dumb question....I have a machined empty front cover. Turned mine in to a machine shop as a core a month ago. What's the best way to find out what boost valve length is needed?

Which company you can recommend me for fast parts for 4l60e parts???

You don't machine the pump housing? Just the pump cover? What is done to correct the wear in the pocket? We machine both halves here.

@randy1ization

Жыл бұрын

what is your business info? need to get a pump side resurfaced.

I'm trying to get the pump in, but I can't get it to offset and it's not really centered. I've done this before, not a pro by any means. It looks like you just threw it together and done. What's the secret please?

I am looking for a replacement pump slide for my 1991 Astro Van with 4L60 tranny. Can't seem to find a source. Please help.

I wonder why nobody has ever made a gasket to go between the pump halves.

@rylandallas9907

10 ай бұрын

most pumps are metal on metal, dont want gasket material to enter the pump area

How did you remove the bushing and seal

@expressautotransmissiondav4207

2 жыл бұрын

The pump bushing and seal I use a sharp 5/8 chisel to remove and the bushing I use a bushing chisel. I use an arbor press to install the bushing and seal

What clearances do you set the Slide / Rotor / Vanes to sir?

@rylandallas9907

10 ай бұрын

GM 4L60/4L60e Rebuild Procedures by Cliff McCormick, manual has all the clearances in it, can find it free on the internet

Do you know any reputable shop in Houston Tx that can work on my transmission

@expressautotransmissiondav4207

2 жыл бұрын

Unfortunately I do not.

Hello how are you ?plz my 4l60e work good on 1 n R just 2 n3 n 4 bad start to slip from 2000 rpm under 2000 work good I use to test the line pressure all time 55psi on all gears stop and drive same max 63 psi on R start from 35 to 90psi just I send it to rebuilt work 3 week and back same problem

@expressautotransmissiondav4207

2 жыл бұрын

So line pressure won't go above 63 psi? Also what year is it do you have a way to watch epc command

@rockabichebel

2 жыл бұрын

@@expressautotransmissiondav4207 just on reverse go to 93 psi on other gears max 63 psi it's a hummer h3 swap 6.0 l gen 3 and transmission h3 but we change the pump and torque convert and pump and shaft n v8 bell housing with ecm green n blue connector drive by cable

@rylandallas9907

9 ай бұрын

i had a bad AFL valve on mine, it was stuck in the bore @@rockabichebel

Can’t hear anything you’re saying over this god awful music you got going on.

@expressautotransmissiondav4207

2 жыл бұрын

Sorry about that have been trying to figure out secondary audio levels hopefully newer videos are better.

@lauraelizabeth7840

2 жыл бұрын

@@expressautotransmissiondav4207 it’s all good it’s just sensory overload lol trying to listen to you on the tv and I can’t hear you over it. My bad for being an ass. I’ll check out the new ones!

@expressautotransmissiondav4207

2 жыл бұрын

Lol it's all good we're still very very new to this but we've had an absolute blast making videos. As far as an ass gooes that wasn't bad at all 😂😂😂

@lauraelizabeth7840

2 жыл бұрын

@@expressautotransmissiondav4207 I bet! They’ve been super helpful and informative and thanks I guess 😂😂😂 it’s been one of those weeks!! 🙃

@expressautotransmissiondav4207

2 жыл бұрын

That's awesome and it's been the same here terrible week for sure