Thanks for this, just bought a house with one of these systems already installed had to figure out how to program it. Really helpful!

@AlarmGrid

3 жыл бұрын

You're welcome. We love it when our videos help someone out. Should you ever decide to get your system monitored, we hope you'll keep us in mind. We have reasonable, no-contract monitoring.

@garretthoward13

Жыл бұрын

Did you have to reset the controller because you wanted to reset the password?

Huge help! Thank you, Sterling!

we moved into a house with all this intalled. but they did not leave any info. how do we get connected? is there a company that we have to pay to beable to program our thermostat and door bell. thanks!

Thanks for the fantastic tutorial. You are the man.

Very in-depth training. Thank you for this video!

@dimchobaev2835

2 жыл бұрын

Perfect

Thank you for refreshing my memory. I haven't touched a 2 GIG panel in so long. I had forgotten everything about it. Good video. Good job.

Thanks brotha, this video was very helpful!

Can you post a video on how to install the 2GIG Wireless Keypad (PAD1). On this system in the video

Can you do a video on installing the 2gig take (super switch) which converts hardwire zones from a previous alarm system wireless zones

Thanks, helped me out a lot.

You are a hero

How do you change the battery in sensor

How do I change the language? I bought a house and this system was already installed but I can’t figure out how to change to english

How long do the batteries last on the window sensors?

how do I enable the configuration button.. Vivint blocked it and now when I hit that button..it says disabled.. see tech support

thanks for the videos! I wonder if you can help me. i bought a house with the go!Contol panel. all sensors all all are connected as with 2gig smoke heat detector. it is unmonitored. can i reprogram it myself and monitor with my smart phone eg alexa or google, independent of a security companies monitoring and expensive fees?

Hello...I like it and I have a question? where could i buy the sensor door? Thanks.

I had a simplisafe security system, I now have the 2gig. Can I use my simplisafe sensors with this 2gig system? They're wireless

Do you have a video on 2gig tied in with flow valve

@SterlingDonnelly

7 жыл бұрын

No, we don't have that video now but we can add it to out list of videos to make. Are you trying to integrate a Z-Wave water flow valve? If so, we usually recommend the Fortrezz WV-01.

Do you have a video about installing an indoor siren? I need one for the second floor. please and thank you.

@SterlingDonnelly

8 жыл бұрын

+Larry Hunter Unfortunately, we don't but you should be able to add an indoor Z-Wave siren to your 2Gig system pretty easily. This FAQ should help - www.alarmgrid.com/faq/is-there-a-wireless-siren-for-the-2gig-gocontrol.

hey sterling. When I enrolled my DW10 Door/Window sensor into my 2gig go control panel for the first time, after i did the auto enrollment with the sensors serial number, I came acrost the loop number and my panel enrolled my window sensor with loop number 2 instead of loop 1. Is it normal for the panel to put the sensor onto loop 2?

@fasttrackstormcenter

7 жыл бұрын

Thank you Frank. I was very confused

How do you program existing door/window sensors to this 2GIG keypad? In the video you say you can use them, but how do you program them?

@dylanalarm_grid1038

3 жыл бұрын

As long as the sensors are compatible, the steps shown in this video will apply to existing sensors as well. After the serial number is added, either manually or by using the learn feature, the next question in the zone programming will be the equipment age.

Hello - Great video! It helped me set up my system. Do you know if there is a way to set the sensitivity of a door contact sensor? Recently the wind has been blowing on one door and barely moving it out of place causing the alarm to go off. Could it also be low batteries in the sensor? Thanks!

@SterlingDonnelly

8 жыл бұрын

+Home Owner There's no "sensitivity" setting exactly but there is a magnet spacing gap of .85 inches so that if the door can move enough to separate the magnet from the contact more than .85", you'll need to re-install them to be a bit closer. When disarmed, you should not be able to pull on the door handle with the door closed and have the sensor "fault" as that would indicate a strong wind could set off a false alarm when you aren't home.

Had issues with tripping motion while sending signals any tips?

@juliaross1667

7 жыл бұрын

Most wireless motions have a 3 minute transmit inhibit unless they are in test mode. If you fault the motion, for example during exit delay, that means it'll be 3 minutes before the motion will send another fault transmission to the panel. It would help to know for sure which motion you're working with.

Recently purchased a home with the system already installed for home monitoring only. The system indicated low battery so I changed it in the main unit and armed the system by mistake. I don't have the disarmed code so is there an override code for this system?

@DKAlarmgridSupport

2 жыл бұрын

Hey Everett, Do you have a Security panel as shown in this video? If so there are no back door or default override codes. Have you tried the default master 1234 user code? Hopefully the previous homeowner reset the codes prior to leaving the home.

Do I follow these same steps to replace a faulty slim wireless contact??

@lizrussell3890

3 жыл бұрын

Yes! Same situation for me. Just need to replace broken sensor. Do I have to do all these steps?

Merci beaucoup

@AlarmGrid

5 жыл бұрын

De Rien!

Just wondering, If some breaks into your house and rips the panel off the all or destroys it during the entrance delay, would that mean no signals go through?

@AlarmGrid

8 жыл бұрын

+Dean Webster Generally these systems, as well as the Honeywell systems are going to come with protections against "smash and crash." The 2GIG Go!Control is no exception. It works with Alarm.com which provides such protection to anyone with one of these panels.

Need help, I just bought a used system and system configuration says access disabled contact technical support

@j07216507

6 жыл бұрын

Bryce Alarm I’m not looking to buy a subscription I just want to use it as a local system

@pianoproductions1237

4 жыл бұрын

Same

How do I clear a tamper code after changing a sensors battery?

@traviscox7336

Жыл бұрын

Usually a disarm of the panel will do. If you cant just do a disarm. Arm the panel then disarm and it should clear if resolved. Email with any further questions.

@josemendez7291

Жыл бұрын

@@traviscox7336 what's the email address?

System was already installed, we reset the system and password but how do we programs sensors already installed atound the house?

@freddaniels8259

Жыл бұрын

Hello G, If you follow this video it walks you through enrolling sensors. If your sensor type is not DW10, then it is still the same method but you would activate the specific transmitter you have.

@garretthoward13

Жыл бұрын

@@freddaniels8259 my main question is do inhave to take the magnet and the sensor over to the controller or can i re program all the sensors from where they are all over the house. This system was already installed when we moved in but we didnt know the passcode so my wife reset the controller but also in doing so unregistered all the sensors.

What is the user code for changing system configuration?

@dylanalarm_grid1038

Жыл бұрын

That would be the installer code, the default of which would be 1561.

@johnfredette5758

Жыл бұрын

@@dylanalarm_grid1038 Thank you.

what is the master code ...

@SterlingDonnelly

8 жыл бұрын

+HUMMER MUSIK The default master code would be 1111 on a GoControl panel.

@hummermusik2037

8 жыл бұрын

sorry i got it

@hummermusik2037

8 жыл бұрын

THANKS STERLING

My alarm company wants $145 per sensor and 1.5 hrs x $75 for labor. What a rip off.

quit ademco to go copy them but make it a headache

@AlarmGrid

3 жыл бұрын

We agree, the Go!Control is difficult to program. They did better with the GC3 and GC3e (but inexplicably, not with the GC2e)!

@1godgodgodgodgod

3 жыл бұрын

@@AlarmGrid yes the gc3 is more menu driven. The gc2 is menu driven nightmare lol

How do I restart my system after a power outage? It is wired, no outlet.

@juliaross1667

7 жыл бұрын

Circuit Breaker, though there should be a plug somewhere, it just may not be obvious (there has to be a step-down transformer.) Is the battery plugged in but dead?

@catherinealdea5219

7 жыл бұрын

Julia Ross I checked the circuit breaker and nothing.

@catherinealdea5219

7 жыл бұрын

Don't see a battery plugged

@catherinealdea5219

7 жыл бұрын

It was pre construction setup

@juliaross1667

7 жыл бұрын

Ok...let me back up. For starters, you shouldn't have to do anything after a power outage, the system should just come back up, in the event that power was out long enough to drain the battery and cause it to power down in the first place. Exactly which panel do you have?