#heaterdooractuator #2007fordmustang #tips here's a quick tip to replace a heater door actuator
Жүктеу.....
Пікірлер: 22
@amorgan58442 жыл бұрын
the best example of setting the position if its not in place!!
@greatwhite64263 жыл бұрын
Thank you bro!! have not seen a video that tells you this, I was struggling to get it back in earlier and finally found this video!
@Coalcoman925
3 жыл бұрын
Glad it was helpful
@MrWatereetiger Жыл бұрын
Thank you so much for this video, I wish I had seen it earlier! 😆
@Coalcoman925
Жыл бұрын
You're welcome please subscribe
@Ariesstubbornbutt Жыл бұрын
Thank you!
@Coalcoman925
Жыл бұрын
Anytime. Please subscribe 🙏
@swaggyc4436 Жыл бұрын
Might be a long shot but yo carnal I juss bought a mustang and all actuators are disconnected and I don't which is which any help ?
@Coalcoman925
Жыл бұрын
The cables from the upper one doesn't reach the bottom one. What I don't know is if both connections on both actuators are the same.
@chrusfletcher86833 жыл бұрын
Which control the temperature. I was told the temperature blend door actuator but when I change my climate to heat it stays cold
@Coalcoman925
3 жыл бұрын
That would be the upper actuator. That was the one i replaced.
@Notjakegg3 жыл бұрын
Hey man when you are putting the actuator in what mode do you have it set to off or defrost?
@Coalcoman925
3 жыл бұрын
Align it like the video here. If it's not Align to the mark, connect it to the harness then turn the AC on till it turns to the mark. Once it's lined up turn off the vehicle. Then install it. Hope it helps.
@Coalcoman925
3 жыл бұрын
To defrost
@fredosantana83732 жыл бұрын
What part number is the one at the bottom that controls the hot ? or which one is that one called ? Thanks
@Coalcoman925
2 жыл бұрын
604-231 5F9Z19E616EA Please subscribe to my channel
@fredosantana8373
2 жыл бұрын
@@Coalcoman925 just subscribed, thanks for replying now another question . Do you have to calibrate the bottom one a certain way like the one you changed in the video or is it just a simple change & put the new one in
@Coalcoman925
2 жыл бұрын
Yes. Do the same as in the video. Unless it's right on the mark already.
@goofymonster4355 Жыл бұрын
Whenever I turn the car on it starts to move out of the position without me even touching the controls
@Coalcoman925
Жыл бұрын
You only turn the key to set it to position. When it's on the mark turn it off and install it. Don't leave the car on. Only to put it in position. Then turn it of when it reaches the mark. Subscribe. Any questions let me know if i can help. Thanks
@Coalcoman925
Жыл бұрын
When you install it it supposed to go in place and it won't move anymore. Make sure where it sits is not damaged
Пікірлер: 22
the best example of setting the position if its not in place!!
Thank you bro!! have not seen a video that tells you this, I was struggling to get it back in earlier and finally found this video!
@Coalcoman925
3 жыл бұрын
Glad it was helpful
Thank you so much for this video, I wish I had seen it earlier! 😆
@Coalcoman925
Жыл бұрын
You're welcome please subscribe
Thank you!
@Coalcoman925
Жыл бұрын
Anytime. Please subscribe 🙏
Might be a long shot but yo carnal I juss bought a mustang and all actuators are disconnected and I don't which is which any help ?
@Coalcoman925
Жыл бұрын
The cables from the upper one doesn't reach the bottom one. What I don't know is if both connections on both actuators are the same.
Which control the temperature. I was told the temperature blend door actuator but when I change my climate to heat it stays cold
@Coalcoman925
3 жыл бұрын
That would be the upper actuator. That was the one i replaced.
Hey man when you are putting the actuator in what mode do you have it set to off or defrost?
@Coalcoman925
3 жыл бұрын
Align it like the video here. If it's not Align to the mark, connect it to the harness then turn the AC on till it turns to the mark. Once it's lined up turn off the vehicle. Then install it. Hope it helps.
@Coalcoman925
3 жыл бұрын
To defrost
What part number is the one at the bottom that controls the hot ? or which one is that one called ? Thanks
@Coalcoman925
2 жыл бұрын
604-231 5F9Z19E616EA Please subscribe to my channel
@fredosantana8373
2 жыл бұрын
@@Coalcoman925 just subscribed, thanks for replying now another question . Do you have to calibrate the bottom one a certain way like the one you changed in the video or is it just a simple change & put the new one in
@Coalcoman925
2 жыл бұрын
Yes. Do the same as in the video. Unless it's right on the mark already.
Whenever I turn the car on it starts to move out of the position without me even touching the controls
@Coalcoman925
Жыл бұрын
You only turn the key to set it to position. When it's on the mark turn it off and install it. Don't leave the car on. Only to put it in position. Then turn it of when it reaches the mark. Subscribe. Any questions let me know if i can help. Thanks
@Coalcoman925
Жыл бұрын
When you install it it supposed to go in place and it won't move anymore. Make sure where it sits is not damaged