Пікірлер

• 
  @zapwhampow54617 күн бұрын

  Thanks for this. It definitely works with guillotine cutters. Most people who say that it doesn't work usually make one of two mistakes. 1. they don't cut long enough. You should cut a minimum of 30 times with a straight blade. With a rotary blade you should cut a minimum of 30 times all the way around the blade. 2. They don't use think enough foil. Use Heavy Duty foil at a minimum, or fold your foil at least 6 layers thick. This will keep your rotary blades nice and sharp. One More tip; don't wait until the blade is totally dull. This should be regular maintenance.

• 
  @jenniferedward775310 күн бұрын

  Thank you so much.. It's really helpful. Since I missed my demo from the dealer, have been usin my sew and go 8 by using your videos. Thanks much. (A bit aftraid to use without proper knowledge, though I went through the manual)

• 
  @LittleEllysElizabeth9 күн бұрын

  Happy to help ..good to know that my amateur videos are helpful to few people

• 
  @athiratom915921 күн бұрын

  Do you know any brand rotary cutter with pinking blades?

• 
  @neelamramalya22 күн бұрын

  Hi... Can we do it on garments without backing.?

• 
  @athiratom9159Ай бұрын

  Hi . How is the rotary cutter? Where are you from in india? I would like to buy one..but couldn't copy the link you provided

• 
  @LittleEllysElizabeth21 күн бұрын

  Hi...can you check my latest community post? The link is there.

• 
  @lizbeth00019 күн бұрын

  Thank you❤

• 
  @imane5009Ай бұрын

  Thank you for the video. I have the same exact sewing mashine. Singer talent 3321. But when i switch to the other decorative stitches either gris or the bleu ones. Nothing happen. It just give me a normal sewing or start making some ugly stitches that has nothing to do with the choosing one. Btw it's a new mashine. So i don't really know how to fix that and start using different stitches. If you have any solutions i hope u can share it with me. thank you

• 
  @LittleEllysElizabethАй бұрын

  Adjust the tension and width....lower the tension..and use interfacing or stabilizers

• 
  @imane5009Ай бұрын

  @@LittleEllysElizabeth thank you sooo mush 😊. That really helped a lot

• 
  @minivalenteena4863Ай бұрын

  Your Mother Mary embroidery is amazing.I used to do anchor embroidery stitch kit. But I never had the thing that holds the stitch cloth properly. Can you please tell me,from where did you brought those?😊

• 
  @LittleEllysElizabethАй бұрын

  Thank you for your kind words. That frame is called Q-snap. I got this from America. I think the website called threadshop.in had these..but they are expensive.

• 
  @allisonm.8497Ай бұрын

  Thank you for explaining to lower the tension on those stitches. Someone else’s video said to leave it at 4, and that just wasn’t looking right. You made it more understandable to me and I really appreciate it!

• 
  @LittleEllysElizabethАй бұрын

  Hei..thank you for taking time to leave a comment. I was also so scared to play with tension in my early days...and this was something I discovered accidentally...

• 
  @manjuchawla76972 ай бұрын

  I will be grateful if you guide me which one is better Bernette7 or 8 What is the difference between 7 or 8

• 
  @jutkagaudi33822 ай бұрын

  Szèp kèzimunka gyönyörű szép zene😊

• 
  @LittleEllysElizabeth2 ай бұрын

  Thank you

• 
  @Egroup4313 ай бұрын

  Keep growing looks awesome 💪

• 
  @LittleEllysElizabeth3 ай бұрын

  Thanks! Will do!

• 
  @Egroup4313 ай бұрын

  @@LittleEllysElizabeth doing great😀😃

• 
  @aileenc89053 ай бұрын

  Thank you for sharing this sneak peak! God bless.

• 
  @LittleEllysElizabeth3 ай бұрын

  Thank you

• 
  @reshmajames373 ай бұрын

  Lemon anchor thread code

• 
  @LittleEllysElizabeth3 ай бұрын

  278 might be a good match

• 
  @LittleEllysElizabeth3 ай бұрын

  Also check 289

• 
  @claytonburton77214 ай бұрын

  'PromoSM' 😬

• 
  @LittleEllysElizabeth4 ай бұрын

  😀

• 
  @LittleEllysElizabeth4 ай бұрын

  Modpodge amzn.to/49Tf0at

• 
  @LittleEllysElizabeth4 ай бұрын

  amzn.to/4bFH8zp Link for the fabric from Amazon

• 
  @Malayali4054 ай бұрын

  Suji idunnathum... Nul idunna പൊസിഷൻ ഒന്ന് കാണിക്കാമോ ചേച്ചി

• 
  @LittleEllysElizabeth4 ай бұрын

  kzread.info/dash/bejne/omGTpZisZZnIitY.htmlsi=EkWs6S_I9az3uu2E

• 
  @Malayali4054 ай бұрын

  മലയാളത്തിലായിരുന്നെഗിൽ നല്ലതായിരുന്നു

• 
  @MyFashionHub-tc5 ай бұрын

  Madam plz show how to do zigzag using this machine. I have bernette sew and go 8 but zigzag is very complicated i feel. Show plz show how to do

• 
  @LittleEllysElizabeth5 ай бұрын

  Are you talking about zigzag stitch or doing pico for saree?

• 
  @MyFashionHub-tc5 ай бұрын

  @@LittleEllysElizabeth zigzag for saree using this machine footer

• 
  @SafeenaAboobacker5 ай бұрын

  സർവീസ് ഇടാമോ. ഓയിൽ എവിടെയൊക്കെ കൊടുക്കണം

• 
  @LittleEllysElizabeth5 ай бұрын

  Will try. Next week

• 
  @nafilanafi41985 ай бұрын

  ക്ലോത്ത് കട്ടറിൻ്റെ ലിങ്ക് ഒന്ന് ഇടുമോ അതിൽ നിന്നും കിട്ടുന്നില്ല. സസ്ക്രൈബ് ചെയ്തിട്ടുണ്ട്

• 
  @LittleEllysElizabeth5 ай бұрын

  amzn.to/3OaJ3ly

• 
  @LittleEllysElizabeth5 ай бұрын

  കട്ടർ മാത്രം പോര. മാറ്റും വാങ്ങിക്കണം

• 
  @LittleEllysElizabeth5 ай бұрын

  amzn.to/3UgcXIL

• 
  @hansfredrikjohansson87425 ай бұрын

  I tried out, but for me it does not work ? Do you need a certain tension on the thread or maybe a special thickness on the thread ? Please help me ? I tried Big capital letter “F” (Patterns II and code 16) and it almost broke my needle and stopped. Then I tried Patterns I : code 93, 96, and 97 it worked but it does not look exactly as the picture and it is not beautiful and the form is not constant ??

• 
  @LittleEllysElizabeth5 ай бұрын

  Let me give a try and get back to you

• 
  @hansfredrikjohansson87425 ай бұрын

  Hello again, After tested several thing. I found that the following worked for me : Using a thinner thread, and a sort of paper support that I ironed on the soft tissue (if the tissue is to soft), and the « A » foot, and I took (this time) a lot of care (when threading the upper thread) to guide the thread around the thread guide pulling the thread through the pre-tension spring. This is very important ! Attention that the thread go down in the gap between the two blade, which is the pre-tension spring. Before I did not put it correctly. And also, I noticed, the tension of the thread is important when winding the bobbin. I hold it slightly between my fingers and used I higher speed (between middle and low). And I checked carefully that there are a certain tension in the thread when pulling it. Both for the upper and lower thread. And also, for the lower thread, when inserting the bobbin, I noticed, another thing that is important, that is to make sure to hold gently with one finger on top of the bobbin when you draw the thread, following the arrow markings into the stitch plate thread guide from A to B and finally to C. (See Manual, page 9, to be found on internet, see internet site below). Then I tried different tension from zero to 7, and found out that, for me, tension 5 was the best option when sewing letters. And, finally it worked, I succeeded to write my name perfectly. I never thought that you had to be so precautious about the threading, the tension of the thread, the tissue support, and the type of foot. (The manual can be found here: www.bernette.com/en/models/bernette-sew-go-8, Or more precisely here : www.bernette.com/assets/uploads/general/Downloads/User-Manual/Sew-Go/EN/5029008.0.04-IM_sewgo-8H20HEN230630.pdf) //Fredrik

• 
  @LittleEllysElizabeth5 ай бұрын

  @@hansfredrikjohansson8742 Thank you. Have pinned your comment so that others can find it easily

• 
  @Simon.maxime.vidal.6 ай бұрын

  J’adore toutes les machines à coudre

• 
  @LittleEllysElizabeth5 ай бұрын

  I am not sure if you had a question...but thanks for the comment

• 
  @alekhya2926 ай бұрын

  Where did u buy the patterns from ? Pls share . Thank you

• 
  @LittleEllysElizabeth5 ай бұрын

  The red truck www.etsy.com/in-en/listing/1327876436/christmas-truck-cross-stitch-pattern?click_key=8cb0c6a15fecb12284640672fea03671901da0fb%3A1327876436&click_sum=d68b49e0&ref=shop_home_active_1&pro=1&sts=1

• 
  @LittleEllysElizabeth5 ай бұрын

  mamageek.co.uk/unicorn-cross-stitch-pattern-free-printable/

• 
  @shahnasmohsin17096 ай бұрын

  Where did I get it?

• 
  @LittleEllysElizabeth5 ай бұрын

  From this website: www.threadshop.in/

• 
  @LittleEllysElizabeth7 ай бұрын

  Find us on instagram to order the kit. instagram.com/marygoldbyme/

• 
  @LittleEllysElizabeth7 ай бұрын

  Find us on instagram to order the kit. instagram.com/marygoldbyme/

• 
  @LittleEllysElizabeth7 ай бұрын

  instagram.com/marygoldbyme/

• 
  @LittleEllysElizabeth7 ай бұрын

  instagram.com/marygoldbyme/

• 
  @NasirKhan-tm1px7 ай бұрын

  Price

• 
  @LittleEllysElizabeth7 ай бұрын

  Check link under pinned comment

• 
  @ramyababuraj39737 ай бұрын

  Mam when i cook using this vessel, that dish becomes light black colour and iron taste also.Especially tomato curry.

• 
  @LittleEllysElizabeth7 ай бұрын

  That means it is not seasoned well. Also since tomato curry is acidic, remove it from the vessel as soon as you finish cooking.

• 
  @Kotohira_7 ай бұрын

  omg that little truck piece is so cute!

• 
  @LittleEllysElizabeth7 ай бұрын

  Thank you

• 
  @LittleEllysElizabeth7 ай бұрын

  amzn.to/3QHf3hi

• 
  @StephanASmith7 ай бұрын

  Praise be to our great God Jesus Christ 🙏🏾 ✝️

• 
  @LittleEllysElizabeth7 ай бұрын

  Amen

• 
  @LittleEllysElizabeth7 ай бұрын

  Corner punch tool : amzn.to/3QWx90j

• 
  @cristinazandacz8 ай бұрын

  Thanks for pour explications 🙏😉

• 
  @LittleEllysElizabeth8 ай бұрын

  Happy to help

• 
  @LittleEllysElizabeth8 ай бұрын

  Embroidery Supplies from www.hoopables.in @hoopables

• 
  @luciatat40849 ай бұрын

  I have the 3323 model but mine doesn’t sound like this one. It’s much more quiet and goes more smoothly. Is your machine very old, or maybe you didn’t oil it? Just curious why it sounds so loud.

• 
  @LittleEllysElizabeth9 ай бұрын

  This video was recorded 3 years back and was bought in 2013. So not sure if it is the problem of the particular model or age or lack of service. Then it is recorded in close range.

• 
  @gourimahan12289 ай бұрын

  Solution for uneven stitches

• 
  @LittleEllysElizabeth9 ай бұрын

  Check if the needle is correct. Thicker needles for thick fabrics and thinner needles for thin/ light fabrics

• 
  @gourimahan12289 ай бұрын

  Thank you mam.with your guidance i could rectify the problem 🙏

• 
  @LittleEllysElizabeth9 ай бұрын

  @@gourimahan1228 Great. Happy to help.

• 
  @akhmagemilang41279 ай бұрын

  Good

• 
  @LittleEllysElizabeth9 ай бұрын

  Thank you

• 
  @gourimahan12289 ай бұрын

  Bobbin jumps solution

• 
  @LittleEllysElizabeth9 ай бұрын

  1. Try screwing needle plate tightly 2. Sometimes it has moved out of alignment. Will need to be placed properly. Give for service.

• 
  @gourimahan12289 ай бұрын

  Ok.mam

• 
  @LittleEllysElizabeth10 ай бұрын

  Isomar Acrylic Ruler :amzn.to/480fX0x Olfa Rotary Cutter: amzn.to/3sN9nKz

• 
  @shivanivlog93910 ай бұрын

  എന്റെ ഇതേ സെയിം മെഷീനാണ് പക്ഷേ നൂല് പൊട്ടി പൊട്ടി പോണ് എന്താണ് കാരണം ഒന്ന് പറഞ്ഞു തരാമോ

• 
  @LittleEllysElizabeth10 ай бұрын

  സൂചി മാറ്റി നോക്ക്... 100/16 for thicker fabrics 90/14 or 75/11 for thinner fabrics. Use new needle.

• 
  @user-xu1it2wt9m10 ай бұрын

  কাটিং মেশিনের দাম কতো

• 
  @LittleEllysElizabeth10 ай бұрын

  amzn.to/3jFohhJ

• 
  @LittleEllysElizabeth10 ай бұрын

  I bought this from America

• 
  @evaiba408310 ай бұрын

  Mam ,why the machine sew by it self after I stop stitching,what is the problem with my machine

• 
  @LittleEllysElizabeth10 ай бұрын

  How long has it been since last service? Is the problem when you use foot pedal or start/stop button?

• 
  @safeenaaboobacker729311 ай бұрын

  മലയാളത്തിൽ പറയോ?

• 
  @LittleEllysElizabeth11 ай бұрын

  മെഷീൻ സർവീസ് ചെയ്യാൻ പറ്റിയില്ല. ദൂരം ഉണ്ട്. സർവീസ് ചെയ്തു കഴിഞ്ഞാൽ മലയാളം വീഡിയോ ഇടാം.

• 
  @sazinhazevedo11 ай бұрын

  Thank you very much for your video. It helped me a lot!

• 
  @LittleEllysElizabeth11 ай бұрын

  Good to know. Thank you for your comment

• 
  @Daily-motivation-girl11 ай бұрын

  Wow

• 
  @maryano5511 ай бұрын

  MERCI

• 
  @LittleEllysElizabeth11 ай бұрын

  You're welcome

• 
  @enriquetasacil82111 ай бұрын

  HM at saan makakabili?

• 
  @LittleEllysElizabeth5 ай бұрын

  Amazon