Пікірлер

• 
  @YangBum-o1k9 сағат бұрын

  Good

• 
  @seanstraw8688Күн бұрын

  For a sturdier heat band (but yea, this isn't being re-used), consider cutting an aluminium soda can into a strip perhaps four times the ferrite width - two careful folds using a metal ruler and you have a band. I've even considered using 12 awg solid copper wire scrap to make the band, which is even less work. For holding the iron, take a scrap of wood (say 1.2x6x20cm, though you could go longer) and close to one end auger/hole-saw a hole in it the diameter of the handle of the soldering iron (but smaller than the guard), pass the plug and handle of the iron through the hole. That piece of wood can be viced, clamped, screwed, or propped as needed (in my case, in a slightly pulled out drawer/tray underneath my workbench, with the soldering iron facing up). If necessary, you can cut a notch from an edge of the wood to the hole, so the cord can be slipped in (if your plug is much larger than the handle, or just for quicker insertion). If you have a ferrule crimping tool, this works good for crushing the aluminium into a cylinder that fits into the iron tip. If I were to be doing this often (say doing a lot of rework of a certain model device), I'd consider taking some copper stock and making a squared U to fit over the top of the transformer, with a threaded stud to connect to the iron (thus making it more of a Y), and holes near the ends of slightly extended sides (the "tops" of the U) with a suitable machine screw to pull them inwards. Then the band is reusable and if you set it up right, you can loosen the screw, remove the heated core, and insert another and re-fix the screw - obviously with screwdriver and pliers - without having to let the iron or band cool down between transformers - the built up heat in the band is still mostly there for the next transformer. This disposable band method works fine.

• 
  @r.v.p375912 күн бұрын

  what is tht ic nunber

• 
  @PAIJO-hn1olАй бұрын

  Thanks

• 
  @tomaszbyczek7611Ай бұрын

  Hello. What will happen when you apply a PWM signal to RWPM and LPWM at the same time? Will it stop or will there be a short circuit and damage?

• 
  @larrybrockwell73152 ай бұрын

  Can you provide final code?

• 
  @prashantgupta19832 ай бұрын

  Hi... My Imax B6 AC charger, enter button is not working, i am pressing it for a second or pressing for long time let say 10-15 seconds but it is not working. Can you please let me know what is the issue.

• 
  @saeed68112 ай бұрын

  I have my black CITIZEN watch that I bought back in 2008. As of now the watch is 2.5 times more expensive. Can I repair it's color or even anodize it with another color?

• 
  @1islam13 ай бұрын

  ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

• 
  @narongrachmareongsit19783 ай бұрын

  ❤😂🎉😢😮😅😊. ไฟแอดพ์

• 
  @runnelcks69623 ай бұрын

  *promo sm*

• 
  @something_else_1233 ай бұрын

  Thank you for watching!

• 
  @designnhj84453 ай бұрын

  replace = irf3205

• 
  @Allah_Is_The_creater3 ай бұрын

  Why after i start charging the amperes start going down till 0.1 A

• 
  @kevinfundarek52944 ай бұрын

  Excellent Tutorial! Thanks for posting it.

• 
  @ibrahimparker42294 ай бұрын

  Hi, I have this exact same camera from my dad. There are a lot of old tapes that I want to bring to my PC but I cannot find the batteries anywhere. I think they were thrown away by accident. I have the tapes, the camera, the battery charger, the FireWire cable needed. I cannot translate your video to understand how you can make a battery to work with this camera. I would really like to power this on and use it. If you could explain more, or give me a link for where I can find a battery replacement, I would really appreciate it. Thank you.

• 
  @something_else_1234 ай бұрын

  Thank you for watching! I hope my video helps you. kzread.info/dash/bejne/p4ibvNJ-aLC7lZM.html

• 
  @theochub4 ай бұрын

  It's not working

• 
  @something_else_1234 ай бұрын

  Thank you for watching! But what?

• 
  @adibbadr87155 ай бұрын

  Hi so ..... i can use this driver BTS7..(43A) with my pompe which supports 6A no problem??? Thank you for vedio 😁

• 
  @something_else_1234 ай бұрын

  Thank you for watching!

• 
  @thaivinhledangthai39325 ай бұрын

  Thank you. But my device notice “ volt error” when i charge balance Lipo 1ampe …(2s), confirm or cancel then warn “volt error”. And i charge two batteries connected in series i use power input 12v 120w , choose charging method pb battery, confirm and cancel, then notice volt error. Help me

• 
  @ronishbarakoti43715 ай бұрын

  Hi, how to make IR burning laser and it's can burn matchstick from 1, 2 meter distance with in second.can you make tutorial video for IR laser.

• 
  @something_else_1234 ай бұрын

  Thank you for watching!

• 
  @martinsanchez41236 ай бұрын

  Valor de la resistencia? Porfavor

• 
  @uthaungnyi12576 ай бұрын

  Thanks' useful.😊

• 
  @ozkantapsz23786 ай бұрын

  Resistor ?

• 
  @RESARU096 ай бұрын

  hi, one of my resistors burned out (the resistor close to the output)... any idea what broke and did need any change?

• 
  @dh90996 ай бұрын

  Hi Is your DC motor 12v or 5v please ?

• 
  @something_else_1236 ай бұрын

  Thank you for watching! 12v

• 
  @raidaru6 ай бұрын

  or u throw it in the bin and buy a genuine one 4 only 35$.......

• 
  @user-vm6mv8il6s7 ай бұрын

  problem is you can not center the tip , meaning tip will not be in the center , so it will turn crocket

• 
  @snappycanon7 ай бұрын

  40 years in engineering tells me the same smallest drill I used to use was .7mm. when using a c.n.c machine is like tennis " new drills please. "

• 
  @HichamChahbon-dl4qz7 ай бұрын

  😎👍🙏👏👏✌️

• 
  @freechmentchris58038 ай бұрын

  Can you please help me to link the transformer, and where can i buy it? Thanks

• 
  @kimscheibel22488 ай бұрын

  Thank you for the video. You mention you're using a comparator to detect and signal the zero-point-crossings, but I don't see anywhere in the code that this is used. Could you explain?

• 
  @pierremoisdon89078 ай бұрын

  Can you give a link to th code ? Thanks

• 
  @pierremoisdon89078 ай бұрын

  Excellent 👍

• 
  @miguelesteban92328 ай бұрын

  MOSFET NCE3010🎉🎉

• 
  @shifatunnabi94208 ай бұрын

  i talk with you how i can

• 
  @arup029 ай бұрын

  Awesome

• 
  @something_else_1239 ай бұрын

  Thank you for watching!

• 
  @ajarivas729 ай бұрын

  What’s a pedometer?

• 
  @something_else_1239 ай бұрын

  A machine that measures the number of steps.

• 
  @DIYNEERAJ9 ай бұрын

  What is the value of the register taken out?

• 
  @something_else_1239 ай бұрын

  I think it was less than 10 ohm, but I don't remember exactly what the resistance value was. And I didn't replace the resistor. Thanks for watching!

• 
  @user-ie9jm9xu5o10 ай бұрын

  Kak mosfet dibawah berapa dan tipenya apa?

• 
  @Tefelucky10 ай бұрын

  You r awesom...and qualify person...😇

• 
  @HairyNumbNuts10 ай бұрын

  You don;t need to remove the buttons. Flex the top of the case where it meets the base on the top and bottom edge and they pop apart.

• 
  @ParangSkipeers11 ай бұрын

  Can i ask..i have use 24v 14a dc motor and also connect 24v20a power supply to bts7960.the vcc 5v and ground from arduino.but when mptor is running im test to apply load.what happen is that motor is stop running.can u explain and suggest how could it be and how to solve? Tq

• 
  @something_else_12311 ай бұрын

  Thank you for watching! Ignoring all other conditions and just guessing from the numbers in the question, the input feels low.

• 
  @ParangSkipeers11 ай бұрын

  @@something_else_123 input from supply?

• 
  @electronicartis11 ай бұрын

  good technique just replaced it.

• 
  @리트고DIY11 ай бұрын

  신기 방기😊😊😊

• 
  @리트고DIY11 ай бұрын

  오 좋습니다. 릴 돌릴때 회전 교환비 가 어떤가요? 낚시 는 꽝이라..궁금 합니다

• 
  @something_else_12311 ай бұрын

  5:1 정도 입니다

• 
  @리트고DIY11 ай бұрын

  와.대단 하심니다. 글고 ㅈㅓ도 지금 하드분해 해서 돌리고 있는데 알고리가 이쪽으로 인도를.ㅎㅎ 창작물도 많으시고 잘 배우겠습니다 😊😊😊

• 
  @something_else_12311 ай бұрын

  시청해 주셔서 감사합니다!

• 
  @user-yp5qc2xv7u11 ай бұрын

  제가 밧데리 + -연결을 잘못해서 딱 그 모스핏을 태워 먹었거든요?? 그 모스핏 모델명은 nce3**10인가 그러든데 교체할수 있는 정식 모델명 말씀해 주실수 있나요??

• 
  @something_else_12311 ай бұрын

  미안합니다. 질문을 이해 하지 못하겠습니다.시청해주셔서 감사합니다.

• 
  @ashlirenier639011 ай бұрын

  😑 Promo-SM

• 
  @ahmedfarouk1571 Жыл бұрын

  How are you my friend what is the solution to this problem CONNECT ERROR CHECK MAIN PORT

• 
  @rajendraharsora8006 Жыл бұрын

  Hi bro I have done same as you show in video but it doesn't work what should be the reason?

• 
  @user-nj3rr9zs9l Жыл бұрын

  저도 전원 반대로 인가되 타는냄새나서 보니.동일부품이 잏부 깨졌네요. 회로 패턴은 안보이고. 구해서 교체 해봐야 겠네요. 감사합니다.

• 
  @something_else_123 Жыл бұрын

  시청해 주셔서 감사하고, 성공하시길 기원합니다.

• 
  @projectmanager3532 Жыл бұрын

  Thanks man

• 
  @something_else_123 Жыл бұрын

  Thank you for watching!