Dangerous because the device has to return path to ground.. The Earth is not used !!
@dmytrozahorodnii81156 күн бұрын
What should be the fuse on the cable from the battery? Thank you
@RonnieGaming2369 күн бұрын
Is this support the bigger battery
@azimdaman1114 күн бұрын
I'd like to get your advice. I have this same exact watch but with a black dial. Recently it went through a water damage. I was stupid to wear it when I went for a thermal bath so it went through a series of environment. For example, through the sauna, steam room and I bathed in hot water and cold water. The next day, the watch went all foggy and could tiny droplets of water on the glass. I sent it to Tag and they advised to replace the electronic component, totally understandable. At the same time, they advised me to replace the case back and the dial. Is replacing the case back and dial necessary?
@psycolana13 күн бұрын
There is no need to replace the back and dial unless its damaged, also if the watch is working, remove the battery and dry it.No need of replacement of electronic component, Maybe you would require replacement of gasket. Hope this helps. Few years back a friend had a similar issue i quickly removed the battery left the electronics to dry for a few days and till now watch is moving fine.
@azimdaman1113 күн бұрын
@@psycolana Thank you so much for your input. Ah man, I should have known better. I didn't remove the battery after it happened. Unfortunately, I let the watch go on for about a week and then it stopped working. When it stopped, I immediately sent it to Tag. They diagnosed and said that the electronic component needs to be replaced.
@psycolana13 күн бұрын
@@azimdaman11 how much is tag charging you, if you don't mind sharing.
@azimdaman1113 күн бұрын
@@psycolanaRM1,600 or $340 USD. I’m from Malaysia btw.
@azimdaman1113 күн бұрын
@@psycolana I'm from Malaysia so it's RM1,600 or $340 USD - and this is quite a sum for me. They tried to milk me with the first quotation of RM3,100 or $620, where they costed in bracelet and bezel replacement. I told them to exclude these two and they revised the quotation. Then upon getting your advice, I told them to revise the quotation again to exclude the case back and dial.
@aetherton538624 күн бұрын
I appreciate your tutorial, nice work!
@psycolana23 күн бұрын
thank you
@budman460526 күн бұрын
Excellent video Thank you so much for your direction on how to replace this capacitor you saved me a lot of money they wanted $95.00 + Shipping to replace the capacitor in my wife's watch Thank you so much
@psycolana26 күн бұрын
Most welcome, and I am Glad that this video helped you.
@smartlyintelligent29 күн бұрын
Thank you
@psycolana29 күн бұрын
most welcome
@lanal7214Ай бұрын
thank you just what I was looking for
@psycolana18 күн бұрын
most welcome
@rasec809Ай бұрын
Thanks brother
@psycolanaАй бұрын
Most welcome
@user-tt6yg8ev9lАй бұрын
Well explained
@StefanE.-fc9xoАй бұрын
You saved my day. After the fix it worked as new.
@psycolanaАй бұрын
glad it helped
@federicoraponi4832Ай бұрын
Is it possible to do the same with a MacBook Pro 15 inch Early 2011 2,2 GHz Intel Core i7?
@ichbins46952 ай бұрын
I just fixed my left XTR shifter SL-M952 with the help of your very useful video - thanks you so much! :)
@psycolanaАй бұрын
Glad it helped
@glendehaan44292 ай бұрын
Thank you VERY much from Calgary, Alberta, Canada!
@psycolana2 ай бұрын
Most welcome from Czech Republic
@DEUXFOREVER12 ай бұрын
👍👍👍👍👍👍👍👍👍
@psycolana2 ай бұрын
thank you
@kramu91402 ай бұрын
Ok super
@psycolanaАй бұрын
Thank you
@sushansahu13642 ай бұрын
is the new relay 12.8v?
@kristobin33262 ай бұрын
Good Video !
@psycolana2 ай бұрын
Thanks for the visit
@saikatdebnath992 ай бұрын
what is the name model of the adjustible relay ??
@kyromuley53362 ай бұрын
Thank you very much, your tutorial video help me a lot
@psycolana2 ай бұрын
Glad it helped
@shibdasmallick55402 ай бұрын
Initially it projected a screwed coupler but actually opened a slotted coupler which is very easy.
@batistaestefane2 ай бұрын
Nice tutorial, I was wondering if this swap was possible and everything looks like a direct swap except for the display data cable. My 2011 macbook pro had an i5 originally, I'm considering buying a 2012 i7 logic board. One of the concerns I have is the battery, do you think they have the same/similar specs?
@psycolana2 ай бұрын
Thx, if your battery needs replacement you could get a 3rd party one.
@harryenever60793 ай бұрын
Brilliant video my friend
@psycolana2 ай бұрын
Thank you! Cheers!
@varunynr3 ай бұрын
Very good videos. Big fan.
@psycolana2 ай бұрын
Much appreciated!
@urizen20003 ай бұрын
I am having trouble finding the right crown and sleeve to fit this watch. My father broke the stem and I bought a G10.211 replacement, which fits (although it looks a little long), but the crown I have, while it screws on, leaves a gap showing some of the threads of the stem. It doesn't sit flush. Could you help me find a suitable crown replacement. He has this EXACT watch but it's unclear what the exact crown replacement I need is. I've used the model number T055.417.11.047.00 but still have had no success.
@psycolana3 ай бұрын
Hi, the stem could be shortened using a file, give me a day or two will try to get the measurements of the stem and crown, replacement crown stem can be procured from www.cousinsuk.com/
@urizen20003 ай бұрын
@@psycolana thanks so much that is so helpful
@psycolana2 ай бұрын
@@urizen2000 crown dia is 6mm - 5.8mm aprox, on my prc 200 Hope this helps.
@psycolana2 ай бұрын
and stem length is aprox 11.18mm from the crown post on my watch, i guess you will jut need to trim the length slightly on your watch stem.(remove stem from the crown and trim/flie the stem slight.
@harshpatwardan92772 ай бұрын
@@urizen2000 crown is 6mm approximately and stem length11.19mm approximately
@Fahad_joya_3 ай бұрын
Sir can you make a video on how to change the center console lights to led on wagonr please
@woodfamily59553 ай бұрын
Thank you, just what I needed help with!
@psycolana3 ай бұрын
Glad it helped!
@shanawaperbez3 ай бұрын
What is the price of body cover rubber?
@Fahad_joya4 ай бұрын
Brother has the relay been working fine? Its been 4 years has the relay made any issues?
@psycolana4 ай бұрын
No Issues at all all these years
@Fahad_joya4 ай бұрын
@@psycolana thanks for the reply
@Poraqui4 ай бұрын
Hi! I have a a Tissot e662/762m. Can i use the Tissot quartz ETA G10.212 if I can't find the 211?
@psycolana4 ай бұрын
HI, If the original movement was the 211, yes you can use the 212. thx
@Poraqui4 ай бұрын
@@psycolana thank you!
@owenlaprath41354 ай бұрын
THANK YOU!!!! 😀😀😀
@psycolana4 ай бұрын
most welcome
@slarkiemon4 ай бұрын
@psycolana - Can I use the higher capacity 56Wh?
@jaypeereyes90314 ай бұрын
May I know where did you bought the logic board for mid 2012 13-inch macbook pro? Thanks
@psycolana4 ай бұрын
I have got the logicboards from aliexpress, links have been shared in the description.
@jes2musicz4 ай бұрын
Body cover rubber part really helped me today🙏 Thanks a lotz♥️♥️
@psycolana4 ай бұрын
most welcome
@greatonreviews4 ай бұрын
If I am not mistaken this is the movement also on the Omega + Swatch moonwatch. I understand that this movement is unlikely to be reparable. Isn't that right?
@psycolana4 ай бұрын
New caliber G10.212 replaces caliber G10.211 on the Omega + Swatch moonwatch. The movement can be repaired if you try doing it by yourself, it involves cutting plastic tabs that holds the movement together, once repaired you will need to glue/ melt the the ends of the plastic tabs, you could just replace the movement as it is not so expensive and save the trouble of opening and repairing the movement .
@greatonreviews4 ай бұрын
@@psycolana Amazing ☺️☺️👏👌 Thank you, super helpful ☺️☺️❤️
@psycolana4 ай бұрын
@@greatonreviews most welcome
@shukkoorkk1214 ай бұрын
Very informative. Thank you.
@psycolana3 ай бұрын
Most welcome
@robertleeimages5 ай бұрын
Very good instructional video, clear step by step descriptions
@psycolana3 ай бұрын
Thank you very much!
@ionescu-sile585 ай бұрын
Foarte bun și explicit reparația convectorului ,am mai văzut 2 video de un idiot roman de al nostru care nu vorbea nu explica nimic și mai era întors și cu spatele la cameră 😂😂😂
@victormrivera33625 ай бұрын
Thanks, very detailed and of great help.
@psycolana5 ай бұрын
most welcome.
@akashbanerjee19845 ай бұрын
Bro mere fascino 125 mai work nhi kar raha 😢
@danielmigueldominguezbende83495 ай бұрын
Awesome video. I already made some upgrades on my old Late 2011 MBPro (changed baterry, fan, thermal paste, HDD for SDD, upgraded RAM) and I would say it's working even better than when I bought it back in 2012. Was wondering if changing the motherboard to a MID 2012 is worth it or not.
@psycolana5 ай бұрын
thx, if nothing is wrong with the logicboard don't replace it.
@phrenologygroyper5 ай бұрын
thank you sir
@psycolana5 ай бұрын
most welcome
@bablukmasihmasih47635 ай бұрын
Thank you for your information
@psycolana5 ай бұрын
most welcome
@The_Solo_Drifter5 ай бұрын
Informative tutorial.... Thank you 👍👍👍
@psycolana5 ай бұрын
most welcome
@sayedsalamut29675 ай бұрын
Great video
@psycolana5 ай бұрын
thx
@xs11tim6 ай бұрын
Thanks very much for a clear and helpful vid.
@psycolana6 ай бұрын
your welcome
@BunDhuk6 ай бұрын
I have a late 2011 with the dreaded gpu amd issue, your tutorial gives me the idea to replace mine with a mid 2012 LB thank you for sharing
@psycolana6 ай бұрын
lets us know how it goes
@cruiserbruiserify4 ай бұрын
Yes man!! Even I have the same issue. I'm thinking of going through the same.
@uttambhusal44556 ай бұрын
Good job
@psycolana6 ай бұрын
Thanks
@user-uf4bb5mj1s6 ай бұрын
Many thank's bro
@psycolana6 ай бұрын
most welcome
@dendog-rb4wt6 ай бұрын
Can you make a video replacing a 15" late 2011 Llboard to a 2012.thx for this video
@psycolana6 ай бұрын
yes done link Video Tutorial kzread.info/dash/bejne/o6ODyq-lk8i3cbw.html
Пікірлер
Dangerous because the device has to return path to ground.. The Earth is not used !!
What should be the fuse on the cable from the battery? Thank you
Is this support the bigger battery
I'd like to get your advice. I have this same exact watch but with a black dial. Recently it went through a water damage. I was stupid to wear it when I went for a thermal bath so it went through a series of environment. For example, through the sauna, steam room and I bathed in hot water and cold water. The next day, the watch went all foggy and could tiny droplets of water on the glass. I sent it to Tag and they advised to replace the electronic component, totally understandable. At the same time, they advised me to replace the case back and the dial. Is replacing the case back and dial necessary?
There is no need to replace the back and dial unless its damaged, also if the watch is working, remove the battery and dry it.No need of replacement of electronic component, Maybe you would require replacement of gasket. Hope this helps. Few years back a friend had a similar issue i quickly removed the battery left the electronics to dry for a few days and till now watch is moving fine.
@@psycolana Thank you so much for your input. Ah man, I should have known better. I didn't remove the battery after it happened. Unfortunately, I let the watch go on for about a week and then it stopped working. When it stopped, I immediately sent it to Tag. They diagnosed and said that the electronic component needs to be replaced.
@@azimdaman11 how much is tag charging you, if you don't mind sharing.
@@psycolanaRM1,600 or $340 USD. I’m from Malaysia btw.
@@psycolana I'm from Malaysia so it's RM1,600 or $340 USD - and this is quite a sum for me. They tried to milk me with the first quotation of RM3,100 or $620, where they costed in bracelet and bezel replacement. I told them to exclude these two and they revised the quotation. Then upon getting your advice, I told them to revise the quotation again to exclude the case back and dial.
I appreciate your tutorial, nice work!
thank you
Excellent video Thank you so much for your direction on how to replace this capacitor you saved me a lot of money they wanted $95.00 + Shipping to replace the capacitor in my wife's watch Thank you so much
Most welcome, and I am Glad that this video helped you.
Thank you
most welcome
thank you just what I was looking for
most welcome
Thanks brother
Most welcome
Well explained
You saved my day. After the fix it worked as new.
glad it helped
Is it possible to do the same with a MacBook Pro 15 inch Early 2011 2,2 GHz Intel Core i7?
I just fixed my left XTR shifter SL-M952 with the help of your very useful video - thanks you so much! :)
Glad it helped
Thank you VERY much from Calgary, Alberta, Canada!
Most welcome from Czech Republic
👍👍👍👍👍👍👍👍👍
thank you
Ok super
Thank you
is the new relay 12.8v?
Good Video !
Thanks for the visit
what is the name model of the adjustible relay ??
Thank you very much, your tutorial video help me a lot
Glad it helped
Initially it projected a screwed coupler but actually opened a slotted coupler which is very easy.
Nice tutorial, I was wondering if this swap was possible and everything looks like a direct swap except for the display data cable. My 2011 macbook pro had an i5 originally, I'm considering buying a 2012 i7 logic board. One of the concerns I have is the battery, do you think they have the same/similar specs?
Thx, if your battery needs replacement you could get a 3rd party one.
Brilliant video my friend
Thank you! Cheers!
Very good videos. Big fan.
Much appreciated!
I am having trouble finding the right crown and sleeve to fit this watch. My father broke the stem and I bought a G10.211 replacement, which fits (although it looks a little long), but the crown I have, while it screws on, leaves a gap showing some of the threads of the stem. It doesn't sit flush. Could you help me find a suitable crown replacement. He has this EXACT watch but it's unclear what the exact crown replacement I need is. I've used the model number T055.417.11.047.00 but still have had no success.
Hi, the stem could be shortened using a file, give me a day or two will try to get the measurements of the stem and crown, replacement crown stem can be procured from www.cousinsuk.com/
@@psycolana thanks so much that is so helpful
@@urizen2000 crown dia is 6mm - 5.8mm aprox, on my prc 200 Hope this helps.
and stem length is aprox 11.18mm from the crown post on my watch, i guess you will jut need to trim the length slightly on your watch stem.(remove stem from the crown and trim/flie the stem slight.
@@urizen2000 crown is 6mm approximately and stem length11.19mm approximately
Sir can you make a video on how to change the center console lights to led on wagonr please
Thank you, just what I needed help with!
Glad it helped!
What is the price of body cover rubber?
Brother has the relay been working fine? Its been 4 years has the relay made any issues?
No Issues at all all these years
@@psycolana thanks for the reply
Hi! I have a a Tissot e662/762m. Can i use the Tissot quartz ETA G10.212 if I can't find the 211?
HI, If the original movement was the 211, yes you can use the 212. thx
@@psycolana thank you!
THANK YOU!!!! 😀😀😀
most welcome
@psycolana - Can I use the higher capacity 56Wh?
May I know where did you bought the logic board for mid 2012 13-inch macbook pro? Thanks
I have got the logicboards from aliexpress, links have been shared in the description.
Body cover rubber part really helped me today🙏 Thanks a lotz♥️♥️
most welcome
If I am not mistaken this is the movement also on the Omega + Swatch moonwatch. I understand that this movement is unlikely to be reparable. Isn't that right?
New caliber G10.212 replaces caliber G10.211 on the Omega + Swatch moonwatch. The movement can be repaired if you try doing it by yourself, it involves cutting plastic tabs that holds the movement together, once repaired you will need to glue/ melt the the ends of the plastic tabs, you could just replace the movement as it is not so expensive and save the trouble of opening and repairing the movement .
@@psycolana Amazing ☺️☺️👏👌 Thank you, super helpful ☺️☺️❤️
@@greatonreviews most welcome
Very informative. Thank you.
Most welcome
Very good instructional video, clear step by step descriptions
Thank you very much!
Foarte bun și explicit reparația convectorului ,am mai văzut 2 video de un idiot roman de al nostru care nu vorbea nu explica nimic și mai era întors și cu spatele la cameră 😂😂😂
Thanks, very detailed and of great help.
most welcome.
Bro mere fascino 125 mai work nhi kar raha 😢
Awesome video. I already made some upgrades on my old Late 2011 MBPro (changed baterry, fan, thermal paste, HDD for SDD, upgraded RAM) and I would say it's working even better than when I bought it back in 2012. Was wondering if changing the motherboard to a MID 2012 is worth it or not.
thx, if nothing is wrong with the logicboard don't replace it.
thank you sir
most welcome
Thank you for your information
most welcome
Informative tutorial.... Thank you 👍👍👍
most welcome
Great video
thx
Thanks very much for a clear and helpful vid.
your welcome
I have a late 2011 with the dreaded gpu amd issue, your tutorial gives me the idea to replace mine with a mid 2012 LB thank you for sharing
lets us know how it goes
Yes man!! Even I have the same issue. I'm thinking of going through the same.
Good job
Thanks
Many thank's bro
most welcome
Can you make a video replacing a 15" late 2011 Llboard to a 2012.thx for this video
yes done link Video Tutorial kzread.info/dash/bejne/o6ODyq-lk8i3cbw.html