Пікірлер

• 
  @rrumsterr4862Күн бұрын

  What are the tools and material needed to build and painting this?

• 
  @StaticModelКүн бұрын

  @@rrumsterr4862 It greatly depends on your expectations, budget and prior experience. For tools - basic is enough: hobby knife, sprue cutters, some paint brushes. As for paint, it depends what painting method you choose, but I assume beginner will start with few cans of Tamiya TS spray and some Vallejo colors for interior painting with a brush. So around 4 to 9 different colors. And also you will need special glue for plastic models, because supper glue and similar is not recommended.

• 
  @stephenb-ly3og5 күн бұрын

  Quick question. At 3:41 there's something leaking from the pink tube, is it oil? What is it? Tysm!

• 
  @StaticModel5 күн бұрын

  @@stephenb-ly3og That is exhaust, and yes, unburned oil is being spit out.

• 
  @stephenb-ly3og4 күн бұрын

  @@StaticModel is the oil in the fuel? Where does it come from? tysm

• 
  @StaticModel4 күн бұрын

  @@stephenb-ly3og the version shown in video is a glow fuel engine, so it uses nitro fuel. Nitro fuel is a mixture of nitromethane, methanol and synthetic oils. You can also build this engine as a petrol one, but than glow plugs must be replaced with spark plugs and special timing devices are required, etc... :)

• 
  @stephenb-ly3og4 күн бұрын

  @@StaticModel Ohhhh gotchu!

• 
  @SoloWing889 күн бұрын

  Bad ass, sharp paint work. Now make one with a JAM sensor /lol

• 
  @StaticModel8 күн бұрын

  I believe actual model is the same, only paint scheme differs. And that one would be quite easier due to included waterslide decals with all the reds, blacks and greens :)

• 
  @user-nq4kh4jr9y23 күн бұрын

  足回りがFCじゃないんだよなあ

• 
  @eaman1129 күн бұрын

  You may also polish the needle with SIDOL or similar products from time to time.

• 
  @ahmelmahay29 күн бұрын

  Sir What paint did you use for the test?

• 
  @StaticModel29 күн бұрын

  Tamiya LP anf XF series paint.

• 
  @eaman1129 күн бұрын

  The common old models run by 12v, if you have a LiPo or any other battery around you can turn it cordless yet without the compressor in your hand.

• 
  @StaticModel29 күн бұрын

  Good idea :)

• 
  @ainttakenanyshitАй бұрын

  Although removing the needle out the front is the BEST way, it would be "better" to re-insert the CLEAN needle from the rear as it would be a more gentle/tapered insertion in/past the needle seal. Re- inserting the needle from the front would have the flat/blunt end passing through the seal which is not optimal and the flat end would not be kind to the seal-like a doctor giving you an injection with a FLAT needle tip; painful to skin and "painful" to the seal 🙂. SO, out the front-in from the rear....

• 
  @zbow1974Ай бұрын

  its ok if you have thin enough paint, i use mine to make t-shirts at the flea market, have 3, that way i can have a fresh charged one at all times.

• 
  @1442GlennLaneАй бұрын

  Playing music to drown out the noise from the compressor. 😂

• 
  @haleonfourwheels6929Ай бұрын

  Hi, did you use two separate batteries for the starter and glow plugs?

• 
  @StaticModelАй бұрын

  Hi, yes exactly. The idea behind it is to make troubleshooting easier and eliminate voltage dips when starter is spun.

• 
  @Tess_untamedАй бұрын

  You should put " AIR CAN " in warm water while using it, so it doesn't ice up.

• 
  @nsvaluto48328Ай бұрын

  Mayville have the wiring diagram for starter switch. I have this motor and other tips I can't get mine started

• 
  @xXturbo86XxАй бұрын

  Where in the hell did a compressor cost only 50 euros just 7 years ago? It never went for less than 90 where i live.

• 
  @StaticModelАй бұрын

  Which one are you talking about?

• 
  @elijahsstudio1109Ай бұрын

  I got a completely different air compressor. Still don’t know how to attach it.

• 
  @user-hl5cf7px1rАй бұрын

  原作雪風って翻訳されてるんだろうか

• 
  @Captain_Draco2 ай бұрын

  I got one of these E91s with a secondhand setup of the compressor with a G22 and G25 which I use pretty often, but never got around to using this one. I have a large 3D print I need to prime and paint and figured the larger volume of the syphon feed jar would come in handy. I wish you'd have tried the airbrush with a compressor for a comparison.

• 
  @ungurdani83462 ай бұрын

  Salut my friend super car super video subscribe subscribe .....

• 
  @StaticModel2 ай бұрын

  Thanks :)

• 
  @mp087bg72 ай бұрын

  Could you tell me what the number of the paints you are using is?

• 
  @StaticModel2 ай бұрын

  Hi, it was more than 8 years ago, so I don't really remember. But i remember using google and finding instruction with Tamiya's FW190 and their own color recommendations. Some metallic's, black & white were from "Italeri", cause they used to brush paint quite good, but other colors were Tamiya XF series.

• 
  @mp087bg72 ай бұрын

  @@StaticModel ok thanks.

• 
  @theblukatlife2 ай бұрын

  Hello I just bought this but now they sell it as "oxygen atomizer for beauty" or something like that, I wanted to paint some scratches on my car with it 😅 but I pour some acrylic paint and it was too thick for it, do you think I could mix it with some "solvent" to dilute it? I painted the scratches with a brush but it looks ugly 😅

• 
  @StaticModel2 ай бұрын

  If you are talking about real car than this is definitely not the way to go. Especially if scratches are deep you won't be able to do a propper touch up job. Because scratch repair requires filling in the scratches and not just painting over. Also brush painting might not be the best way. I'd opt for a special tool which creates paint droplets or a touchup marker - with these tools you are "pooling up" the pain in to scratch and not painting over. Might be something you'd like to look in:) If you still decide to use airbrush you can add thinners to the paint but it must be suitable for the paint type you are using and also multiple layers will be required.

• 
  @theblukatlife2 ай бұрын

  @@StaticModel I'll follow your advice thank you 🙂

• 
  @tankoradosslotcarworld2 ай бұрын

  nice work

• 
  @paulburns42092 ай бұрын

  Looks great how long did it take. Any tips for using tweezers to put decals on the car as mine don’t place well

• 
  @StaticModel2 ай бұрын

  Not long at all, about 1 hour in a very relaxed manner. I think best tip is to not touch model or decals with a bare hands, better to use latex gloves or latex finger tips. Cause oily residues we leave with our bare hands greatly decrease chance of decals sticking properly:)

• 
  @Miko-cz3fw2 ай бұрын

  Perfect solution for car models 😮

• 
  @StaticModel2 ай бұрын

  Almost forgot, get it here! For all types! s.click.aliexpress.com/e/_EJfpgvZ s.click.aliexpress.com/e/_oDP4G5Y s.click.aliexpress.com/e/_DcGntlr

• 
  @misty4932 ай бұрын

  cool clip

• 
  @LassetUnsSpielen2 ай бұрын

  thanks for suffering. the only use i can see in the spray-can-setup is that theres no loud compressor working, so you could work at night

• 
  @ungurdani83463 ай бұрын

  Salut my friend super car super video subscribe subscribe ....

• 
  @user-il6kx7ir4i3 ай бұрын

  Отлично вышло! Скажите вы просто втирали пигмент без фиксатора?

• 
  @StaticModel3 ай бұрын

  Переведено с помощью Google. Переведено с помощью Google. Спасибо, потому что я использовал очень небольшое количество пигмента - я не использовал никакого фиксатора. Он притупляет первоначальные цвета пигмента. Но в ситуациях, когда мне нужно создать грязь или подобные эффекты, я использую матовый акриловый лак для закрепления пигмента.

• 
  @user-il6kx7ir4i3 ай бұрын

  @@StaticModel Спасибо за отзыв,дошел до нанесения пигментов на матовый лак Ганзы ( жду сутки когда высохнет лак) и думаю как лучше нанести пигменты!? Думая сначало тонкий слой закрепителя,а затем пигменты..но посмотрел ваше видео и задумался.Собирая Королевского тигра Менг,ваша модель очень достойна! Без воды и лишней болтовни! Кратко и по делу весь процесс.Спасибо.

• 
  @misty4933 ай бұрын

  COOL!

• 
  @ONFLOOD-RC3 ай бұрын

  Amazing car construction mate!!! Nice video🥇👍👍👍

• 
  @StaticModel3 ай бұрын

  Thanks, glad you liked it:)

• 
  @scaleffect3 ай бұрын

  Awesome work. Had my eye on this kit for a while, this video will definitely be a reference for me if I try one. Thanks for sharing your hard work!

• 
  @misty4933 ай бұрын

  One more great video <3 Good luck

• 
  @Miko-cz3fw3 ай бұрын

  Big work!

• 
  @jfc2133 ай бұрын

  the prop is a bit sad ????? no

• 
  @StaticModel3 ай бұрын

  ?

• 
  @shaheerhazmanfitri98403 ай бұрын

  damn nice.. i want this model

• 
  @gokhanersan85614 ай бұрын

  The first honest review of these cheap airbrushes. You need to thin the paint too much, since they don’t atomize that good. However, attaching an Iwata to that cordless compressor would change everything. That’s what I want to do.

• 
  @StaticModel4 ай бұрын

  Hi, I really do think it is not worth it. Pairing high quality spray gun with low pressure air source won't make a noticable difference.

• 
  @gokhanersan85614 ай бұрын

  @@StaticModel I’d like to give it a try anyway. Some reviewers had luck with that combo. Some portables get close to 35psi that iwata recommends.

• 
  @StaticModel4 ай бұрын

  @@gokhanersan8561 it's peak psi, constat psi will be 18 or similar.

• 
  @clouddweller914 ай бұрын

  Im getting one

• 
  @mikebalis99634 ай бұрын

  I appreciate the honest review which included what the set is good for. The reviewer's English is excellent.

• 
  @emelune5 ай бұрын

  Which machine I take for t-shirt?

• 
  @StaticModel5 ай бұрын

  Not this one for sure, see other options in the description of this video. Go for compressor with air tank. All links are affiliate links.

• 
  @emelune4 ай бұрын

  Thank you :)

• 
  @Gounesh5 ай бұрын

  Awesome video mate! It's just too much hustle to change a color drasticly, multiple airbrushes looks like a must.

• 
  @StaticModel5 ай бұрын

  For quick color swap you don't need to perform deep clean. Flushing with thinner will be enough. But if you tend to use metallic paint/primer/clear coat - multiple airbrushes will make things much easier.

• 
  @tiagoadcosta5 ай бұрын

  brilliant work. have you thought about fading the plastics too? i think washing them in acetone would really fade the black a bit

• 
  @johnsimeonidis75185 ай бұрын

  Best video I've seen for air brush cleaning! Thanks for making this video, it was very helpful.

• 
  @XmortoxX19905 ай бұрын

  I think this will do for minis for my first airbrush

• 
  @haroldomiyaura9125 ай бұрын

  awesome aircraft.

• 
  @ungurdani83465 ай бұрын

  Salut my friend super car super video subscribe subscribe

• 
  @halovski90005 ай бұрын

  Hi, I really like your model. Great work! I'm wondering what glue did you use for window, lights and couple of other parts?

• 
  @StaticModel5 ай бұрын

  Micro Krystal Klear By Microscale

• 
  @daijoubu45296 ай бұрын

  Are you getting the new MN82 licensed LC79?

• 
  @StaticModel5 ай бұрын

  I would love to, body is nice but chassis is not really that interesting. Simply don't want to get more of the same :)

• 
  @WatchMan19626 ай бұрын

  Very nice.

• 
  @border3046 ай бұрын

  Pretty awesome video.

• 
  @polong996 ай бұрын

  The kit that i never finished from 2011 😂

• 
  @StaticModel6 ай бұрын

  Never too late :)