Pretty cool. Have you seen the stuff @GrindHardPlumbingCo builds? Check out their monster bike build.
@cameraman1234567890Күн бұрын
The thing about the 4-stroke is that it has more torque than the two-stroke in the power band so you can run the bigger prop or higher pitch impeller, you need like a 90mm impeller size which is what jetsurf uses to get enough volume. I'm running two 56mm pumps on my electric build.
@cameraman1234567890Күн бұрын
Now I'd try and fit that 4-stroke in the board to see how clean and small you can make it!
@jorgeflogar41762 күн бұрын
Me encanta como va quedando así de dos ruedas
@jacco_por2 күн бұрын
You build like I did when i still could, Love it!
@shane667882473 күн бұрын
Amazing!!! when you shot the fireball to inflate the tire
@bernhardbrm50283 күн бұрын
einfach geil!
@KingyunaInfinity-c4w3 күн бұрын
Looking at it tmc cable
@KingyunaInfinity-c4w3 күн бұрын
I thought Ben hur was true ?? It a book
@PartikleVT4 күн бұрын
You made that intake look way simpler than anyone else I've seen make one. They had way more edges in theirs and it was welded out of multiple pieces. My understanding of fluid dynamics however leads me to believe that the rounder shape you went with is actually going to perform better. Nevertheless, it was great seeing you make one fairly simple because I need to make one for my custom setup at some point as well.
@deanedeane43184 күн бұрын
Bloody (nearly) good job Man !!!...... sometimes you just gotta step back from a project for a bit ...... very looking forward to see the next installment !!! 😉🙃😎
@littlelifters75434 күн бұрын
You’re a mad fish in a crazy sea sir.
@BennyNeptune4 күн бұрын
This is the fine line between janky and genius that i truly admire
@DktheWelder4 күн бұрын
It’s a thin line and I often fall to the janky side haha
@ronbuckner81794 күн бұрын
Ok you got me. Your oddiously is addictive!
@elidelia26535 күн бұрын
looks like your wire gauge is to small for the current draw. 22awg would make everything way to hot. figure out the amperage of all your components and adjust the wire gauge accordingly. Great project, Killer workshop! best of luck!
@DktheWelder4 күн бұрын
I put some thicker wire and it worked but the whole thing has been changed now
@radekciskowski20705 күн бұрын
you need a gyroscope: kzread.info/dash/bejne/Y3-hyrafmMS9d5s.html :)
@Scrogan5 күн бұрын
fush and chups mate
@whitecompany185 күн бұрын
A 98 Honda XR650 rear shock should be cheap and available where you are and have more than enough adjustment for rebound👌
@michaelhansen64815 күн бұрын
👍👍
@cliftonmassey31435 күн бұрын
There is or was a company called Lit motors that was building a two wheel vehicle, and their balance technology might be good for this guy's project.
@DktheWelder5 күн бұрын
Yes they have two electric gyroscopes under the seat . That might be what I do but have something else I want to try first
@fadedlight85965 күн бұрын
I think for the system to help make it stand. Find out what threads are the quickest for up down motion. Id use them to make like almost hydraulic skids that are quick enough. But to help that i almost wonder if u can make a gyro inside the wheel you might need 2 side by side one might need to spin opposite of the other. And can possibly use like mini bike drum brake pads to stop it.
@msears1015 күн бұрын
Today's video is sponsored by NZ's world famous steel toed safety crocs.
@lumotroph5 күн бұрын
great sfx :D
@lumotroph5 күн бұрын
no need for an outro :)
@gafrers6 күн бұрын
Great work. Love the center hub steering. Bimota style
@leeutubegmail6 күн бұрын
So stoked to see you pick up a nice new printer! Seems like your old one was holding you back a bit.
@benschlack58146 күн бұрын
Pretty sweet, wished the video was longer 👍
@LACARRINDANGA6 күн бұрын
Thats cool
@KnifeKnut6 күн бұрын
Take a page from the Monoracer and instead of stationary balance use retractable outrigger wheels that also work as wheels against the ground when retracted in the event of a tipover. I recall one clip where it was deliberately driven in a turn so tight it laid down onto the retracted wheel, was stopped, and then was recovered in the same way. Your Batbike might not be able to do exactly that maneuver, but the general crash safety principal (not to mention saving the bodywork) is the same.
@shaynegadsden6 күн бұрын
You're a brave man to have thing mounted near your sack might be a long pants only vehicle
@jeremyweaver95986 күн бұрын
You've done more tweaking on that bike than a meth-head! Good job!
@markpage6606 күн бұрын
Nice work mate. Wish i lived in NZ to come check it out in person. Glad the word "Munted" has reached you guys.
@geoffburrill98506 күн бұрын
Love the ingenuity.
@michaelroberts62996 күн бұрын
broken wrist with battery drill; make sure its in 2 gear when it breaks through
@DiHandley6 күн бұрын
Burt Munro’s cousin!
@nickthelebo6 күн бұрын
This thing has come along way bud
@mickmuzzmkmz16286 күн бұрын
Your shenanigans always cracks me up!😅 Don't ever change!!👍 "Holy batshit Batman!".
@mellows19706 күн бұрын
😀😂
@DirtyDovi6 күн бұрын
2:31 You're not kidding! These things'll rag-doll ya if you're not careful! Sort of like w/ exploding cut-off disks and getting wire wheels stuck in shoelaces.. If it's Never happened - You've got the best of luck! haha GREAT TIP!!
@DirtyDovi6 күн бұрын
Your CAD and Fab skills Rock, bro! I was TRYING to follow along as you were designing your worm-gear... Damnit, I'm just too tarded still for this stuff not to fly over my head.. Excellent Job! That turned out amazingly! Hey, how are you liking your K1 Max? I ventured into 3D printing w/ a Bambu Lab X1-C, but as previously mentioned - just too stupid still to grasp CAD [This coming from someone who was schooled in hand/manual mechanical drafting]
@DktheWelder6 күн бұрын
The cad drawing took quite a long time to learn I just watched lots of KZread videos on fusion 360 , sure you could figure it out
@DirtyDovi6 күн бұрын
@@DktheWelder Ah no kidding?! Good on you bro!! I dabbled w/ Auto Cad back in early 2K's then jumped straight into Solid-Works. *That's what completely threw me. Then tried a few others - equally confusing. Fusion 360. Yessir, that's what I've been deep diving into lately. Great program - if/when someone can efficiently use it! Thanks bro, I'll keep pluggin' away for sure!
@MsJon526 күн бұрын
entertaining with creativity, mechanical design and fabrication, with a hint of danger, my kind of channel, lol
@DktheWelder6 күн бұрын
Haha I try to easy up on the danger but it just keeps happening!
@drewanderson82796 күн бұрын
Hell ya brother!! I love this project!
@DktheWelder6 күн бұрын
It is a challenging yet fun project
@peter360adventures96 күн бұрын
Awesome build
@DktheWelder6 күн бұрын
Thanks
@Ben-Dixey6 күн бұрын
Always wanted to try and ride a bike with backward steering, I don't think you need the additional challenge with this bike though. Impressive CAD skills, if only it could print metal parts. Have you ever used the printer to make patterns for casting in metal ?
@DktheWelder6 күн бұрын
I have thought about it a bit but casting looks pretty difficult and time consuming
@BruceLyeg6 күн бұрын
I recognised that music at 0:28! Make sure you wear snug fitting underwear when your driving it to keep your bits out of the gears and chain. It's a bit tippy, innit?
@DktheWelder6 күн бұрын
I might have to wear some tights for safety
@appleapple38556 күн бұрын
Don't worry about it. Take your time. I'm enjoying the ride!
@DktheWelder6 күн бұрын
There is a lot of backwards and forward working with whatever I can find but it is getting there 👍
@kingmarz36356 күн бұрын
Enjoyed watching from South Island New Zealand we understand it’s hard to weld a shitload of stuff raise a family hold down a full-time job and upload videos takes a minute Your humor reminds me of Billy T And bike looks so sick!
@DktheWelder6 күн бұрын
Haha Billy t is the man , thanks for the kind comment I often see you commenting 👍
@892632305596 күн бұрын
1:00 Что за музыка на 1:00 играет?
@DktheWelder6 күн бұрын
It is in the description with a link
@892632305595 күн бұрын
@@DktheWelder большое спасибо!
@ItsBoyRed6 күн бұрын
I'm so happy its back on two wheels! This is going to mad once its done
@DktheWelder6 күн бұрын
Haha the 3 wheel idea wasn’t the go aye! Now there a lot of challenges getting it to balance
Пікірлер
6:00 that creek looks like paradise, beautiful 👍
Pretty cool. Have you seen the stuff @GrindHardPlumbingCo builds? Check out their monster bike build.
The thing about the 4-stroke is that it has more torque than the two-stroke in the power band so you can run the bigger prop or higher pitch impeller, you need like a 90mm impeller size which is what jetsurf uses to get enough volume. I'm running two 56mm pumps on my electric build.
Now I'd try and fit that 4-stroke in the board to see how clean and small you can make it!
Me encanta como va quedando así de dos ruedas
You build like I did when i still could, Love it!
Amazing!!! when you shot the fireball to inflate the tire
einfach geil!
Looking at it tmc cable
I thought Ben hur was true ?? It a book
You made that intake look way simpler than anyone else I've seen make one. They had way more edges in theirs and it was welded out of multiple pieces. My understanding of fluid dynamics however leads me to believe that the rounder shape you went with is actually going to perform better. Nevertheless, it was great seeing you make one fairly simple because I need to make one for my custom setup at some point as well.
Bloody (nearly) good job Man !!!...... sometimes you just gotta step back from a project for a bit ...... very looking forward to see the next installment !!! 😉🙃😎
You’re a mad fish in a crazy sea sir.
This is the fine line between janky and genius that i truly admire
It’s a thin line and I often fall to the janky side haha
Ok you got me. Your oddiously is addictive!
looks like your wire gauge is to small for the current draw. 22awg would make everything way to hot. figure out the amperage of all your components and adjust the wire gauge accordingly. Great project, Killer workshop! best of luck!
I put some thicker wire and it worked but the whole thing has been changed now
you need a gyroscope: kzread.info/dash/bejne/Y3-hyrafmMS9d5s.html :)
fush and chups mate
A 98 Honda XR650 rear shock should be cheap and available where you are and have more than enough adjustment for rebound👌
👍👍
There is or was a company called Lit motors that was building a two wheel vehicle, and their balance technology might be good for this guy's project.
Yes they have two electric gyroscopes under the seat . That might be what I do but have something else I want to try first
I think for the system to help make it stand. Find out what threads are the quickest for up down motion. Id use them to make like almost hydraulic skids that are quick enough. But to help that i almost wonder if u can make a gyro inside the wheel you might need 2 side by side one might need to spin opposite of the other. And can possibly use like mini bike drum brake pads to stop it.
Today's video is sponsored by NZ's world famous steel toed safety crocs.
great sfx :D
no need for an outro :)
Great work. Love the center hub steering. Bimota style
So stoked to see you pick up a nice new printer! Seems like your old one was holding you back a bit.
Pretty sweet, wished the video was longer 👍
Thats cool
Take a page from the Monoracer and instead of stationary balance use retractable outrigger wheels that also work as wheels against the ground when retracted in the event of a tipover. I recall one clip where it was deliberately driven in a turn so tight it laid down onto the retracted wheel, was stopped, and then was recovered in the same way. Your Batbike might not be able to do exactly that maneuver, but the general crash safety principal (not to mention saving the bodywork) is the same.
You're a brave man to have thing mounted near your sack might be a long pants only vehicle
You've done more tweaking on that bike than a meth-head! Good job!
Nice work mate. Wish i lived in NZ to come check it out in person. Glad the word "Munted" has reached you guys.
Love the ingenuity.
broken wrist with battery drill; make sure its in 2 gear when it breaks through
Burt Munro’s cousin!
This thing has come along way bud
Your shenanigans always cracks me up!😅 Don't ever change!!👍 "Holy batshit Batman!".
😀😂
2:31 You're not kidding! These things'll rag-doll ya if you're not careful! Sort of like w/ exploding cut-off disks and getting wire wheels stuck in shoelaces.. If it's Never happened - You've got the best of luck! haha GREAT TIP!!
Your CAD and Fab skills Rock, bro! I was TRYING to follow along as you were designing your worm-gear... Damnit, I'm just too tarded still for this stuff not to fly over my head.. Excellent Job! That turned out amazingly! Hey, how are you liking your K1 Max? I ventured into 3D printing w/ a Bambu Lab X1-C, but as previously mentioned - just too stupid still to grasp CAD [This coming from someone who was schooled in hand/manual mechanical drafting]
The cad drawing took quite a long time to learn I just watched lots of KZread videos on fusion 360 , sure you could figure it out
@@DktheWelder Ah no kidding?! Good on you bro!! I dabbled w/ Auto Cad back in early 2K's then jumped straight into Solid-Works. *That's what completely threw me. Then tried a few others - equally confusing. Fusion 360. Yessir, that's what I've been deep diving into lately. Great program - if/when someone can efficiently use it! Thanks bro, I'll keep pluggin' away for sure!
entertaining with creativity, mechanical design and fabrication, with a hint of danger, my kind of channel, lol
Haha I try to easy up on the danger but it just keeps happening!
Hell ya brother!! I love this project!
It is a challenging yet fun project
Awesome build
Thanks
Always wanted to try and ride a bike with backward steering, I don't think you need the additional challenge with this bike though. Impressive CAD skills, if only it could print metal parts. Have you ever used the printer to make patterns for casting in metal ?
I have thought about it a bit but casting looks pretty difficult and time consuming
I recognised that music at 0:28! Make sure you wear snug fitting underwear when your driving it to keep your bits out of the gears and chain. It's a bit tippy, innit?
I might have to wear some tights for safety
Don't worry about it. Take your time. I'm enjoying the ride!
There is a lot of backwards and forward working with whatever I can find but it is getting there 👍
Enjoyed watching from South Island New Zealand we understand it’s hard to weld a shitload of stuff raise a family hold down a full-time job and upload videos takes a minute Your humor reminds me of Billy T And bike looks so sick!
Haha Billy t is the man , thanks for the kind comment I often see you commenting 👍
1:00 Что за музыка на 1:00 играет?
It is in the description with a link
@@DktheWelder большое спасибо!
I'm so happy its back on two wheels! This is going to mad once its done
Haha the 3 wheel idea wasn’t the go aye! Now there a lot of challenges getting it to balance
the sheer talent man love the build
👍