Пікірлер

• 
  @danjones1897Күн бұрын

  Thanks! Good video. Hey, you DO NOT actually need the shop vac. Once you get the soaking wet clothes out, scoop out as much water as you can using a cottage cheese container or something similar. That will make the machine light enough to pivot out away from the wall and access the back panel. There's one 1/4 inch nut holding on a plate where the drain hose comes out. Remove that panel, and that will allow you to place the hose flat on the floor so you can simply drain the washer into the floor drain. (CAUTION! This only works if your laundry room DOES have a floor drain!)

• 
  @jorgekiller5 күн бұрын

  Jajajaja mexican touchers 😂😂 en España dicen que son unos tocamexicos

• 
  @kenrcooke662 ай бұрын

  Great Video! Thank you so much. This video save me a lot of time and money.

• 
  @williameggleton4143 ай бұрын

  If I had to choose who would save them, let's just say since they're American, it's understandable why those bozos wanted to do the job. HOWEVER, since the Canadians claimed they were in Canadian waters, the latter should be the ones who'd rescue them due to nationalism and territories. So the Americans were just being pushy assholes. : /

• 
  @halfdedadturner4 ай бұрын

  Thanks man just what I was looking for

• 
  @philearly23134 ай бұрын

  This was a very informative video. I do not agree with putting anti-seize on rubber components. It’s not designed for that and can potentially cause o-ring failure. anti-seize is designed to prevent metal surfaces from bonding together it is NOT a lubricant for moving surfaces. Now that being said I thought it was a very good video with LOTS of useful info.

• 
  @nnmek71738 ай бұрын

  My first time using a front load washer. A used one . I don't have an overflow of water in the drum, but after washing and taking my clothes out, I will spin the drum and I hear water inside the drum but it's not visible. Is this normal?

• 
  @knucklhedbbq8 ай бұрын

  Yeah, pretty typical to have a little water still in there, for that reason, most folks will leave the door slightly open to allow it to air out. If I remember correctly, at start up, the machine briefly does a very short drain cycle to pump out any excess water before starting a new cycle.

• 
  @icemangresham8 ай бұрын

  Is that a 30 quart bowl or bigger?

• 
  @knucklhedbbq8 ай бұрын

  Way bigger than 30qt, if I remember right it's like 80qt. It can hold 75-85lbs of ground meat easily. It's stainless and weighs 25lbs empty, it's a beast! **Edit, if you watch again, right as I start grinding, I say that the bowl has 40lbs of meat in it, that should give you a better idea of how ridiculously massive it is.

• 
  @icemangresham8 ай бұрын

  @@knucklhedbbq yeah was looking at 80 qt with a cart and it was $1400. Also I just got a #42 meat grinder. And is no joke! I borrowed a #32. From a friend and loved it. I have a 50 pound mixer but I’m thinking about going with a big bowl like you got

• 
  @knucklhedbbq8 ай бұрын

  @@icemangresham I got REALLY lucky and got that bowl, without the cart, at a restaurant equipment auction for $60, THEN I saw how much they cost new and couldn't believe it! TBH, if you have a mixer, I don't know that you really need the bowl - I did all my mixing by hand and the bowl was great for that, so much better than a meat lug. But if you have a mixer, meat lugs might be the easier and cheaper way to go. Washing and storing that bowl is awful, even with a large commercial 3 sink. A very useful tool for many things, but I think $1400 might be spent elsewhere. 👊 🍻

• 
  @icemangresham8 ай бұрын

  @@knucklhedbbq meat makers are nice for doing tacky sausage like pepperoni, hard salami, but just a light mix not worth the trouble of cleaning up

• 
  @donmaclaren4409 Жыл бұрын

  that grind in the small plate looks real good when the meat didn't look partially frozen, super nice gind with that meat

• 
  @mrnaughtycat Жыл бұрын

  Viagra falls lol

• 
  @joelwilson1018 Жыл бұрын

  How did you get the water out

• 
  @knucklhedbbq Жыл бұрын

  Take the wet clothes out first and then use a shop vac to suck it out thru the drain hose... The video @ 1:34 shows how, have fun! 🤪

• 
  @wn2948 Жыл бұрын

  great video, saves a lot of time and money. everything was right on and the replacement of the pump motor was fast and simple. Thanks

• 
  @MartinGarcia-wy5kh Жыл бұрын

  My has a fl and do code that appears. Some water remains in washer it started making a crackling noise?

• 
  @chair1456 Жыл бұрын

  exactly!

• 
  @kennethgilbertdds7249 Жыл бұрын

  I found that the pump motor can be dis assembled and cleaned. 4:30 Inside motor was gunked up. Bearing and shaft were not broken. Cleared and cleaned all this out. Re assemble. Great results. Works great now.

• 
  @rickcurtis2983 Жыл бұрын

  Thank you!!

• 
  @user-gg3rg1gg5x Жыл бұрын

  What season and episode I love this one

• 
  @MSU-DetroitFan Жыл бұрын

  S15 E18 Catch 'em if You Can

• 
  @belloa3026 Жыл бұрын

  This washer is junk. Only used it two times and now it will not drain

• 
  @belloa3026 Жыл бұрын

  Where did you buy pump? How much?

• 
  @rachaelgreenland2662 жыл бұрын

  My school

• 
  @mattneff12622 жыл бұрын

  Is this linked to the error code tE?

• 
  @knucklhedbbq2 жыл бұрын

  Mine was giving the drain error code, don't remember what the code was.

• 
  @triciaesquibel89882 жыл бұрын

  Thank you so much. My son and i were able to fix the washer!!!! I hope and your family will always be blessed!!!

• 
  @ryangarnache67772 жыл бұрын

  Excellent, glad to help!

• 
  @draysonm46012 жыл бұрын

  Very good video lots of detail

• 
  @219Tucker2 жыл бұрын

  antiseize is not a lubricant..........sigh

• 
  @bjarnieinarsson34722 жыл бұрын

  Aaarrggg.. you don't want to seal this pump up. If you do, it will not be able to cool itself and bearings (plastic one) will melt and wobble i.e. stop working!

• 
  @ryangarnache67772 жыл бұрын

  Good to know!

• 
  @giovannigonzales51522 жыл бұрын

  I'm better off with the U.S. than with Canada.

• 
  @senanquliyev51882 жыл бұрын

  👍👍👍👍👍👍👍👍

• 
  @stanhill39803 жыл бұрын

  Is there a reset on the motor itself

• 
  @Sophiasapprentice3 жыл бұрын

  Excellent video, thanks so much for the help. My setup had one hose clamp and one squeeze clamp - and of course, the squeeze clamp was on the front side of the rubber boot, and was a pain to get off. But other than that, this vid was perfect and extra helpful. :)

• 
  @rkknight31273 жыл бұрын

  Thanks for the video - hubby replaced our pump and washer is back in action!

• 
  @paulawolanski32373 жыл бұрын

  Puck slapping maple suckers 😂😂😂

• 
  @sgtjohnson3 жыл бұрын

  If it’s the bigger falls it’s Canadian territory

• 
  @zetroc883 жыл бұрын

  Lmfao!!!!

• 
  @user-rx5sf7qc1p3 жыл бұрын

  Jajajaja

• 
  @samhuckabee56003 жыл бұрын

  Thank you so much for your help!!!!

• 
  @kari07tacoma3 жыл бұрын

  Thank you. I just pulled out a rock the size of a quarter & it’s draining again! You saved me money!!!

• 
  @Lord_Joseph174 жыл бұрын

  Can it grind a whole Turkey bone and all ?

• 
  @JohnAK724 жыл бұрын

  Hi, Is there any oder configuration not having the pressure switch directly over the pump assembly? I also seen some Neptune washers with recirculation pump! That’s pretty interesting to see different varieties of Neptune :)

• 
  @lisasmith20164 жыл бұрын

  I just bought one of these, waiting for it to be delivered. Want to grind bones for dog food. Can it handle beef and pork rib bones?

• 
  @EmilyAlbojer4 жыл бұрын

  Can it? I was told only rabbit or chicken bones.

• 
  @vqphan4 жыл бұрын

  Will a faulty drain pump keep the washer from spinning?

• 
  @ryangarnache67774 жыл бұрын

  In a way, yes - but there are other things that could cause that. If the pump isn't working, the washer will still be full of water, and therefore won't go into it's spin cycle... Run a cycle and watch it closely, wait for it to go into it's drain cycle and gently lift the drain hose out of the wall drain. Is there a significant amount of water being pumped out or is it just a trickle? Does the pump sound rough/noisy? You should be able to trouble shoot it a bit further to determine if the pump is working properly or not. Also, it's not terribly difficult to remove the drain pump, if you're unable to determine good/bad through trouble shooting, you might want to just pull the pump and check it out.

• 
  @DonianMgmt4 жыл бұрын

  Thanks, man. I appreciate this. Pretty cut and dry but you added a few hints that worked really well. Be safe!

• 
  @z31rider244 жыл бұрын

  How long have you had this washer for? I just bought a Neptune MAH5500bww. for $80. couple days ago. It's in operating condition. Is this washer any good?

• 
  @calebkoch67244 жыл бұрын

  Ok , that was a waste of time.

• 
  @bogey190184 жыл бұрын

  The hopper is there for a reason.

• 
  @Murray99334 жыл бұрын

  *My friend and I do a lot of home canning☞☞>**allmy.tips/Cabela_grinder?h8** We used this to grind all the veggies for making Salsa, made short work of it. It worked beautifully. No fluid back flush around the shaft, like I've had other grinders do. Excellent design, function and value.*

• 
  @user-kz1wk3im8m4 жыл бұрын

  Thanks for posting. I just fixed my washer Sala like this one. There is debris inside the pump nom machine working fine.

• 
  @kyle60475 жыл бұрын

  Canadians love The Simpsons.

• 
  @jimmcquiston39115 жыл бұрын

  Thank you for this. i was trying to unscrew the one side of the pump that looks like it is threaded.

• 
  @sonyas13495 жыл бұрын

  So I have part number 62902090 ppgf30 and nothing pops up to be maytag neptune motor pump. Could I use another motor but different part number ?

• 
  @sonyas13495 жыл бұрын

  The plastic propeller end is broken. What is that called ? Could that be a problem ?