Пікірлер

• 
  @avikahlon7 күн бұрын

  I am in the middle of replacing the flex cable of the camera yaw . One of the 3 small screws that connects it to the bottom of the drone got wasted. Any advice?

• 
  @Droneted6 күн бұрын

  If the gimbal has never been removed from the drone, one of the screws has glue in the center of the screw and you have to pick it out with a pointed object like a needle. If it is damaged I use an ez out tool.

• 
  @timothystucker9332Ай бұрын

  Do you have a possible solution for a dji phantom 4 pro that the camera won't tilt up or down. I replaced the yaw arm and roll arm and yaw motor because I bought it after someone had crashed it

• 
  @DronetedАй бұрын

  First I have to ask if the gimbal goes through the start up procedure? The pitch would move up and down during start up. if it does the problem is in the remote controller settings.

• 
  @brandonthompson7976Ай бұрын

  Hello are you still working on phantom 4 drones? I could really use your help!

• 
  @DronetedАй бұрын

  Yes I am. you can email me at [email protected]

• 
  @gilbojohn24892 ай бұрын

  I need the link that motor

• 
  @Droneted2 ай бұрын

  www.ebay.com/itm/255599530976?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=MpO6DztRRhm&sssrc=2047675&ssuid=htIxleKGSaC&widget_ver=artemis&media=COPY

• 
  @Ramadhaniayoubissa3 ай бұрын

  How can I get that compass and I need it for the job of that problem

• 
  @Droneted3 ай бұрын

  It is a Boy Scout compass. Very cheap

• 
  @Ramadhaniayoubissa3 ай бұрын

  @@Droneted I need to buy and how to get it from alixpress or ebay

• 
  @Droneted3 ай бұрын

  Either. eBay might be easier. Where are u located?

• 
  @Ramadhaniayoubissa3 ай бұрын

  @@Droneted It is found in Africa, Kenya

• 
  @Ramadhaniayoubissa3 ай бұрын

  I'm sorry if I get the ebay link so you can buy it

• 
  @narongrachmareongsit19783 ай бұрын

  ❤😂🎉😢😮😅😊ไฟไฟไฟไฟไฟแอดพ์

• 
  @BigMike-dm4oy3 ай бұрын

  Did not know you could sing, like that. You are both 1 in a million, or would that be 2 in a million?

• 
  @djamelbmw22284 ай бұрын

  If we lose the original cover, how can we fix it again? Is there another way to fix it with the new cover that comes with motor

• 
  @Droneted4 ай бұрын

  not really. If you loose the original You have to get your hands on a few casings. If you use the one that came with the where it points. then take the casing off and see where the magnets are located. If it points to the right, you need one with the magnets to the left of where the casing is marked. If it points to the left you need one to the right of it. If you can send me a photo of nwhere you mark it and a photo of where the yaw points I can help you figure it out

• 
  @meruvahari31024 ай бұрын

  From India

• 
  @meruvahari31024 ай бұрын

  sir

• 
  @meruvahari31024 ай бұрын

  Hiii

• 
  @Droneted4 ай бұрын

  hey glad to see you. You do drone repair in India? That is awesome. If you ever need anything let me know.

• 
  @djamelbmw22285 ай бұрын

  Thnx brother But i foolowed and wached some other videos. It owners claim that the broblem is with ESC board.. Is this correct bro?

• 
  @Droneted5 ай бұрын

  You can have a bad esc but 90% of the time it is the yaw motor.

• 
  @djamelbmw22285 ай бұрын

  @@Droneted Ooh ok may god protect u 😊🖐🏻i hve same prblm the camera is not centered but whene i calibrate compass nd rotate the drone. I hear that annoying sound. from gimbal. what's causing that sound? It's like something stuck

• 
  @Droneted5 ай бұрын

  One of the 3 motors is making the noise. It may or may not effect the gimbal. Is your only problem the centering ? I have a video that address that.@@djamelbmw2228

• 
  @djamelbmw22285 ай бұрын

  @@Droneted My prblm the camera always goes left Okay my brother thank u so much my respect to u sir for listening and responding to my comment. Thnx

• 
  @Droneted5 ай бұрын

  Sounds like you need to change the casing on the yaw motor. Where are you located?

• 
  @nick19516 ай бұрын

  I don't know if here where I need to leave a message

• 
  @Droneted6 ай бұрын

  this will work. my email address is [email protected]

• 
  @nick19516 ай бұрын

  @@Droneted I will like to exchange the gimbal and the yam arm already assemble, I'll send you mine, just let me know how much and how can we do it, thanks

• 
  @fabiofasano56227 ай бұрын

  Hello Ted: I have changed the Yaw motor of my PH4 according to your instructions, using the original casing to avoid deviations in the chamber. Despite this, the camera faces to the left, but I don't have other casings to try. Furthermore, the yaw motor does not seem to have enough strength since if I move it manually it takes a while to focus on its wrong direction, not firmly as the other motors do, but weakly as if it were drunk. Do you have any suggestion? Thank you so much

• 
  @Droneted7 ай бұрын

  I have seen a lot of defective yaw motors lately.. Most of the defects are loose windings. If you take the casing off and grab the windings with your fingers they should not move if you try to turn them left or right. I buy 20 at a time and check each one . if they are loose at all I glue them. I recommend you return the yaw motor as it is probably no good. Where are you located? I would be glad to help you.

• 
  @fabiofasano56227 ай бұрын

  Hello Ted. Unfortunately I am somewhat far away, in Buenos Aires, Argentina, where there are not many options to get spare parts at the moment. I bought the engine on eBay. Anyway, I'll try to take it apart again to check it, while I try to get an original motor. We´ll keep in touch. Thank you very much for your answer@@Droneted

• 
  @DronetedАй бұрын

  @@fabiofasano5622 What did you find?

• 
  @user-fi5jo8ks8q7 ай бұрын

  Dear friend, please can you give me your WhatsApp number, I have a problem with the yaw motor

• 
  @jaymay3068 ай бұрын

  Have you noticed on a Phantom 4 that after installing an aftermarket yaw motor, it appears to work fine, but now there's no camera feed showing on the controller? This just happened to me, and I have not had time to investigate it yet, but thought I'd reach out for an idea of where I need to start looking for the problem.

• 
  @Droneted8 ай бұрын

  Probably not the yaw motor. It is probably the ribbon cable. Do you have a camera sensor error?

• 
  @jaymay3068 ай бұрын

  @@Droneted the yaw motor was physically damaged after a hard landing / rollover, as it was explained to me, and hanging loosely. While the drone had a working camera feed, the gimbal didn't work correctly due to the damage. Now the motor is fixed, but the feed is gone. I'll check for error messages when I get home from work and turn it on.

• 
  @Droneted8 ай бұрын

  Ok. I’m here to help

• 
  @robertcroft25918 ай бұрын

  What kind of clip was that?

• 
  @Droneted8 ай бұрын

  We call it a Jesus clip. Probably not the real name.

• 
  @robertcroft25918 ай бұрын

  Snicker snicker hmmm.@@Droneted

• 
  @DetectorismoItai11 ай бұрын

  very good tip my friend Ted Keyser , have you thought about relocating , taking off the magnet and repositioning it so that it is correct ? because in cases where both the esc board and the yaw motor are changed, and they still won't invent a software for this calibration, hug from the friend from Itai sp brazil!!!

• 
  @Droneted11 ай бұрын

  That might just be my next project. I have to figure out how to release the magnet

• 
  @user-io5rt5fi5s Жыл бұрын

  is there a way to check the motor for debris without removing the motor from the drone?

• 
  @Droneted Жыл бұрын

  Spin it by hand. You can feel the difference. If it is dirt you can blow it out with high pressure air. If it is metal you will have to take it apart

• 
  @carolinawingsvideoproducti3030 Жыл бұрын

  Btw ..go4 auto gimble cal works but also takes it back to the left. Could to mount inside have been nudged?

• 
  @Droneted Жыл бұрын

  It is possible. It should move freely.

• 
  @carolinawingsvideoproducti3030 Жыл бұрын

  Hey Ted. P4P hard landing. Gimble yaw slight to left. All cals..imu etc. If I use the go 4 gimble cal (roll/yaw) 100 clicks gamble goes straight but back to left after power cycle. Ideas?

• 
  @Droneted Жыл бұрын

  Check the yaw arm. It may be bent slightly. If it works ok and just points to the left it would be my guess that the yaw motor is not damaged but the yaw arm is bent. Look at it carefully

• 
  @dbbeilin Жыл бұрын

  I have a phantom 4 pro plus. My camera continually moves left to right and right to left upon start-up. I tried calibrating the imu, the compass and the gimbal. can you help?

• 
  @Droneted Жыл бұрын

  You have a damaged yaw motor. I think the Hall sensors are damaged. A tiny scratch will cause this. What my other video about replacing the yaw motor

• 
  @Droneted Жыл бұрын

  kzread.info/dash/bejne/ZqVtyM-dZcy9hrA.html

• 
  @broughamjb Жыл бұрын

  Ted tried the video bit found i knackered 2 of the 4 bearings taking the assembly apart. I have new bearings but cannot get the old ones out?

• 
  @Droneted Жыл бұрын

  sorry to hear that. I use a punch to knock them out. It is long and narrow. I put it through the hole in one bearing. Put it on a slant so it catches the edge of the bearing and tap it out.

• 
  @jeffpara9113 Жыл бұрын

  Hey Ted!! Happiest anniversary to you both!!

• 
  @Droneted Жыл бұрын

  Thanks Jeff

• 
  @LAKEPILOTUSA Жыл бұрын

  Good to see you posting again

• 
  @Droneted Жыл бұрын

  Hey, thanks

• 
  @MrDronebot Жыл бұрын

  Making it to your 50th anniversary, definitely a wonderful world! Congratulations Ted!

• 
  @MrDronebot Жыл бұрын

  Thanks, this is great video!

• 
  @Droneted Жыл бұрын

  you can also use finger nail polish remover. let it sit for a while. Be very careful as the magnets are fragile.

• 
  @MrDronebot Жыл бұрын

  Going to the shop to get my compass right now! Thanks for sharing the knowledge!

• 
  @Droneted Жыл бұрын

  Good luck. Sometimes you have to try a couple but it is better than randomly try different casings.

• 
  @gagolfanddrones487 Жыл бұрын

  So Ted you know you can use that magnet and shaft with a P3 Armature and install them right on a P3 I have done it and it makes an awsome P3 Pro Hybrid

• 
  @basherrasheed5844 Жыл бұрын

  How are you sir do you do a repair service

• 
  @Droneted Жыл бұрын

  Yes I do.

• 
  @basherrasheed5844 Жыл бұрын

  @@Droneted I live in Germany, how can I send you the drone?

• 
  @Droneted Жыл бұрын

  @@basherrasheed5844 you can email me at: [email protected] Shipping is rather expensive from Europe. Is it the whole drone or just the gimbal that needs work?

• 
  @basherrasheed5844 Жыл бұрын

  @@Droneted I have the same problem as in the video, and since someone else tried to fix it, I would like you to check it as well..

• 
  @Droneted Жыл бұрын

  @@basherrasheed5844 So you are having issues with the main motors on the drone not he gimbal?

• 
  @Droneted Жыл бұрын

  Sorry I set it for Kids so comments were turned off.....who knew

• 
  @Ramadhaniayoubissa Жыл бұрын

  I would like to ask if the housing of Phantom 4 pro and Phantom 4 pro v2.0 are interfering

• 
  @Droneted Жыл бұрын

  The shells are the same except the DJI sticker is a different color. The legs are different

• 
  @Ramadhaniayoubissa Жыл бұрын

  @@Droneted 🙏🏻🙏🏻

• 
  @catamaranmentor Жыл бұрын

  Thanks for the video, just got iron sand in mine after flying on an active volcano.

• 
  @Droneted Жыл бұрын

  were you successful?

• 
  @catamaranmentor Жыл бұрын

  @@Droneted have not cleaned it yet will let you know

• 
  @Droneted Жыл бұрын

  @@catamaranmentor I would use CRC electronic cleaner to clean the motors when you open them. Then I would blow them out with compressed air.

• 
  @catamaranmentor Жыл бұрын

  Thanks for the video, just got iron sand in mine after flying on an active volcano.

• 
  @Droneted Жыл бұрын

  at 4minutes and 53 seconds you see the vise with the yaw motor sitting on top. I have switched methods a bit. I now set the yaw motor down in the vise with it sitting on the ears of the casing. This is to prevent damage to the motor.

• 
  @corbettsantanavideographer364 Жыл бұрын

  Hello, Is is very nice what you do. I've learned a lot from watching your clips. Something I'd like to share with you. I had the pointing to the left problem with the camera. Replaced the Yaw motor as you did in this clip. All worked out with the switching the Yaw motor to the original magnetic case. To my disappointment. Still have the same problem. Any suggestions?

• 
  @Droneted Жыл бұрын

  I want to be sure I understand the issue. The gimbal pointed to the left. It did not swing back and forth. You changed the yaw motor and used the original case. It still points left as before. Is it steady and the only issue is that it points left? Did it start doing this all of a sudden or was there a crash or hard landing involved?

• 
  @corbettsantanavideographer364 Жыл бұрын

  Hey @@Droneted - First thanks for getting back to me on this. Started with a crash. After that Started pointing left. Original case used. After repair, camera is steady as before but still points still to the left. 🔧

• 
  @Droneted Жыл бұрын

  @@corbettsantanavideographer364 if nothing is bent I would guess it may be the camera IMU. You can email me at [email protected] Are you in the USA?

• 
  @corbettsantanavideographer364 Жыл бұрын

  @@Droneted Am located in Berlin Germany. IMU? What can I do to adjust this or fix it? Consider sending to you for repair. Depending on the cost.The ones I've met here are incompetent.

• 
  @Droneted Жыл бұрын

  @@corbettsantanavideographer364 You certainly can do that. The last time I shipped to Europe it cost about $50. If you wanted to ship it to me I can either repair it or swap for a refurbished unit. I suggest you email me at [email protected] to discuss the cost

• 
  @humbertoecia2 жыл бұрын

  Ted, I accidentally threw the original house in the trash. there is another procedure to calibrate the yaw

• 
  @humbertoecia2 жыл бұрын

  @@idiottoad1 ohhh God... it's going to be very expensive. the yaw motor here in brazil is the price of a kidney. thank you anyway

• 
  @Droneted Жыл бұрын

  I have a way to solve your problem now. please email me at: [email protected]

• 
  @humbertoecia2 жыл бұрын

  Ted, I accidentally threw the original house in the trash. there is another procedure to calibrate the yaw

• 
  @Droneted Жыл бұрын

  kzread.info/dash/bejne/lHqetLakqd2qgdY.html watch this video it may help

• 
  @basherrasheed58442 жыл бұрын

  Can I send my drone to you to fix it and how much does it cost?

• 
  @Droneted2 жыл бұрын

  Your drone or your gimbal? email me at [email protected] It would have to be very soon or in August

• 
  @Droneted Жыл бұрын

  Cost depends on the issue.

• 
  @bruce.chloereid60902 жыл бұрын

  Awsum information mate thank you

• 
  @stanleybishop94482 жыл бұрын

  Can I send a video? It is hard to explain. When I first turn my p4p on it seems to start caging then the roll gimbal vibrates then roll travels from limit to limit and yaw travels back and fourth. I replaced the roll motor and ribbon cable twice, no help.

• 
  @Droneted2 жыл бұрын

  yes you can. [email protected]

• 
  @kokvad2 жыл бұрын

  5:00 Don't do it! Place the edges of the vise under the protrusions of the body.

• 
  @Droneted Жыл бұрын

  that is how we do it now...thanks. I appreciate your feedback

• 
  @aliabooali85312 жыл бұрын

  👍👏

• 
  @mvivanc2 жыл бұрын

  Great job!

• 
  @mrblackout222 жыл бұрын

  I'm always impressed that you don't need magnification. Good eyes sir.

• 
  @Droneted2 жыл бұрын

  I have bionic eyes dude.

• 
  @djamelbmw22285 ай бұрын

  😅😅yes. This is why I don't touch very small things. My eyes r covered with fog 😂

• 
  @CR125Elsinore2 жыл бұрын

  Hi Ted, Thanks for doing the video. I've replaced the yaw motor and ribbon, using the old bell housing. All works well except after initialization, the camera "cants" slightly to the left when pointing forward, 5~10 degrees or so. Have been flying it that way for a year or so. Do you know if this type of re-calibration needed can be done at home or does one need some type of calibration software. I've searched online and have tried many calibration methods, (drone upright, manually turning , etc.) to no avail.

• 
  @Droneted2 жыл бұрын

  email me and I can explain how to get it to point straight. [email protected]

• 
  @bachisquiri2 жыл бұрын

  Thank you for another great video

• 
  @beautyplussarita62132 жыл бұрын

  Nice 👌👌👌👌

• 
  @maxlackett16302 жыл бұрын

  Good to see a video from you! Been a while. Hope everything is well!

• 
  @Droneted Жыл бұрын

  if the yaw casing is damaged or lost go to this video: kzread.info/dash/bejne/lHqetLakqd2qgdY.html

• 
  @donaughzenia20612 жыл бұрын

  1wtxr vum.fyi