Dankzij jouw video heb ik er ook eentje kunnen herstellen, bedankt :)
@DVAnlАй бұрын
Graag gedaan!
@anthonymyers2064Ай бұрын
Thanks for this just repaired mine just lost about 3 pints all working now 😊
@primo7072 ай бұрын
Brilliant advice...couldn't believe there was that much calcification build up, its amazing it was still working at all! Many thanks DVA
@stephane133703 ай бұрын
Hello, The original battery costs approximately $150. Do you thing it worth it to buy the original please ? How many years do you thing we could keep the battery in a correct % health ? Thank you for your answer, and so great video by the way !
@DVAnl3 ай бұрын
It is still in good shape/ use. To be fair, an after market battery would work just as good.
@petextanky84214 ай бұрын
Just the thing I needed to see, was going to change fan motor after replacing 40a fuse, thanks
@ringovandentroost73874 ай бұрын
goeie uitleg dit filmpje. Zou het kunnen als deze stuk is dat alle standen wel werken, alleen als de sleutel uit het contact is blijft de verwarming doorblazen. Zit die stand 4 rechtstreeks aangesloten? Gaat wel om een auto verwarming, dus niet met de draaiknoppen
@DVAnl4 ай бұрын
Dan zou je hem met een multimeter kunnen doormeten, maar als het door blaast nadat je de sleutel eruit haalt doet vermoeden dat het misschien toch een andere fout is.
@stevec00ps4 ай бұрын
Thanks for this! Just repaired mine after losing at least 2 pints from each barrel in dripping!
@muamerabjelkic85004 ай бұрын
All ok and helpful, only one thing missing: the end of installation! Close te light box!! You forget it :)
@DVAnl4 ай бұрын
You've got it right, i almost forgot it!
@stuartbutcher12334 ай бұрын
Great tutorial 👌 simple and to the point! I have my resistor now so am off to replace it 👍🏻 many thanks.
@johnrowley49935 ай бұрын
Many thanks for this. According to the manual there should be two clips but our car is exactly like the one in the video. The bulb and connector came out after going down a pothole Thanks once again
@johnrowley49935 ай бұрын
Just a ps, there are two t20 screws on either side and on our car they were too tight . Unscrewing them slightly allowed the connector to be located thanks once again
@AyeSiwmae5 ай бұрын
Thanks man, just saved me paying £18 for a 2 minute install!
@DVAnl5 ай бұрын
Glad I could help.
@dsvilledenis76225 ай бұрын
Hi I had the same problem with the display not working, I replaced the three capacitors and the screen comes on for two seconds and goes out again, could it be the quality of capacitors?
@DVAnl5 ай бұрын
It should not matter if it is of a bad quality capacitator, however cheap ones could have flaws.
@rossmeikle80376 ай бұрын
Did you Disconnect the battery?
@DVAnl6 ай бұрын
I did not.
@pencilme1n6 ай бұрын
When putting it back in, if it's a tight fit you may need to apply pressure to the metal wings of the holder rather than the plastic body to avoid too much strain.
@WORVILLE2226 ай бұрын
Hi don’t suppose you could help iv done this and still have nothing I do hear it clicking any other suggestions?
@dustymauve6 ай бұрын
Thanks for this, really clear.
@welingtonluisdonascimento29687 ай бұрын
Grazie
@natkerton7 ай бұрын
Thank you! This really helped out this morning :)
@brianfrun8 ай бұрын
thanks - just what I needed. Now the job is completed the manual makes sense ....
@alistercarmichael49908 ай бұрын
A useful video but there are a number of important points. I have been given one of these machine to fix. Its totally dead. Back cover off. Remove the silver power supply and disconnect it from the middle PCB (black and red). The PSU is 10.5 volts out at upto 10 amps. I set up a bench power supply in place of the original PSU and pushed in the keg switch. Everything works as expected amd the supply indicated a 5 amp load with the pump running, and the fan going.. so turn that off and check the PSU. Dmm the outputs for AC and DC. TO to find a dropping dc voltage and no AC. So the psu is the problem. The thing is this is a switched mode power supply. They are simple enough and have common failures to look for. Hower. THEY CAN BE LEATHAL due to the stored energy and high voltages involved with them. The components replaced in this video are the output capacitors and they may be charged with enough to burn chunks out of tools. The input capacitor could have 400 volts across it and enough stored energy to stop your heart. This will be present after the mains supply is removed and you are now handling the board with the terminals exposed. If the switching FET has shorted you could get very high voltages on the outputs of the supply. Compnents may explode (capacitors usually do, especially if they are electrolytic and connected the wrong way). Also the heatsink can be a live surface at mains potential, especially if there has been a failure on board. Equally when reinstated an insulator shim may be missed. Do not try to repair any switched mode power supply unless you know what you are doing. It could easily be the last thing you ever do.
@gianlucascottex52798 ай бұрын
Well done ,thank you
@1010fan19 ай бұрын
thank you so much
@Kentish94949 ай бұрын
Nice one needed this
@alanbbrady819610 ай бұрын
Didn't see what direction you pulled tge bulb out. Probably the most important bit and we couldn't see it. 😢
@Habeekman10 ай бұрын
Thank you! With this guide I repaired my Perfect Draft!
@johnsearle2411 ай бұрын
No way with dropping the fan motor down. Daft
@nemanjamilosevic828911 ай бұрын
Thank you!!!
@samn114 Жыл бұрын
amazing😍😍😍😍
@kitty07071992 Жыл бұрын
Ik heb hem vervangen maar nu werkt hij nog steeds niet. Bij mij werken alle standen niet.
@luckylook4432 Жыл бұрын
wery good 🤠
@citroenc5dieselkarrmapensioner Жыл бұрын
Pölysuoja jäi pois umpiosta
@DVAnl Жыл бұрын
oops xD
@gerrycoogan6544 Жыл бұрын
Excellent help. Thank you.
@Aszy66 Жыл бұрын
Netjes! Leuk dat je het hebt gefilmd 😃
@PEGELZWO Жыл бұрын
Can you show how to change the foglights? I want to change the old lights to yellow ones! ;)
@roccoviggiani623 Жыл бұрын
Ti sei scordato il tappo di gomma..😃😃😃
@DVAnl Жыл бұрын
Ben individuato! Ora è tornato ;-)
@guiltybyassociation1764 Жыл бұрын
Great video thanks, I stripped it down but the capacitors do t seem the have blown. The unit shows power however when I press the two buttons to simulate a keg being in place the power shuts off
@ikiluify Жыл бұрын
I have the exact same issue any fixes yet?
@babychukka11 ай бұрын
I’ve currently got the same problem. 🤷♂️
@guiltybyassociation176411 ай бұрын
@@babychukka I fixed mine, not sure if it will work for you but here’s what I did. Take off the back exposing all the electronics. Unclip all the individual components ie the fan motor (there should be little push to connect clips. I then turned on the pump and pressed the two buttons where the kegs sits to indicate/simulate and keg in the device. I found that by doing this the display screen didn’t cut out like before which told me there was a fault with one of the components I disconnected. I managed to find out that it was the cooling plate section that was causing it to short out. Now, I’m not sure exactly what I did, maybe I mangaged to clean the electrical components of the cooling plate or merely by disconnecting and reconnecting some how reset it but it stopped shorting out after that. Worth a try at very least
@zweifuffzichbitte Жыл бұрын
this is perfectly done.- thanks! 👍🏼
@TONI_IL_MAGRO Жыл бұрын
Hola muchas gracias por tu video es muy interesante e intructivo .Tengo mi máquina averiada mañana lo pongo en practica pues me quedó un barril recien empezado
@DVAnl Жыл бұрын
You don't want to waste a good barrel ;-) Have fun with the fix because the reward will be delicious :-D
@TONI_IL_MAGRO Жыл бұрын
@@DVAnl without a doubt you already know without pain there is no winner. Thank you
@kaismidic Жыл бұрын
Thank you very helpful
@bikerman6907 Жыл бұрын
Thanks for great vid!👍😊
@analoghin Жыл бұрын
Thank you so much for this video. After watching it I've changed successfully the bulb. I do have a question. Near that bulb are other two bulbs and I realised I have to change those also. Is the same procedure? The one you have changed is H7 12v 55w and I would appreciate if you could tell me the names for the other two. Thank you!
@DVAnl Жыл бұрын
These are not the same procedure, al though the rubber housing works the same. Blinker light is just pull no twist same with parking light. High beam you have to remove the plug en push two prongs out. Blinker light H21W Lights H7-55W High beam H1-55W Parking light W5W Fog light PSX24W
@analoghin Жыл бұрын
Thank you very much! You have been very helpful. Your video is the best!
@arminiuss.316 Жыл бұрын
Thank you! 🙂
@MrOoBAZoO Жыл бұрын
Did anyone resister smoke abit when they installed it ?
@DVAnl Жыл бұрын
I don't think mine did.
@TheSeashel Жыл бұрын
Thank you!! You helped when every other video failed!!
@DVAnl Жыл бұрын
No problem, some times I run into problems as well without a good video. So when I fix it I tend to make a video about it for other people!
@nadw Жыл бұрын
Good video. Just saved me a lot of money - never changed one before and thought would be more complicated than that. Also thanks for the warning on not touching the bulb!
@DVAnl Жыл бұрын
You're welcome and enjoy your new lights ;-)
@villadodizmark2820 Жыл бұрын
Will you please upload another video showing us how to charge the battery for cp1300. And also how to fill up the ing when it's finished
@chopjockey Жыл бұрын
I think you need to learn the difference between Repair and Replace...
@DVAnl Жыл бұрын
Well I repaired the ventilator system by replacing the resistor. It also helps in the search query for other people trying to fix theirs.
@CanaryIrish Жыл бұрын
Bit of a longshot but took the tap apart and I'm left with 2 pieces that don't seem to go anywhere after reassembly. Anyone with a complete breakdown of the tap would be great.
@DVAnl Жыл бұрын
Hi CanaryIrish, go and buy yourself a (lotery) ticket because it is you lucky day! I found a French explanation for you about the handle. Haven't watched the full video but seems to have all the info you need. kzread.info/dash/bejne/gGeXpLVvnLOzqLQ.html Have a nice day!
@CanaryIrish Жыл бұрын
@@DVAnl Super stuff. These things seem to get clogged with limescale and calcified. Stuck my one in a bucket with limescale tablets and it improved somewhat.
@steptoesbar Жыл бұрын
Just want to say THANK YOU this video gave me the confidence to look and sure enough my three capacitors had popped, so ordered new ones yesterday from amazon and fitted/soldered in today and it is all fixed - thank you again - prost
@willspower2051 Жыл бұрын
Hi Can you tell me the spec on the capacitors please so i can order ?
Пікірлер
Dankzij jouw video heb ik er ook eentje kunnen herstellen, bedankt :)
Graag gedaan!
Thanks for this just repaired mine just lost about 3 pints all working now 😊
Brilliant advice...couldn't believe there was that much calcification build up, its amazing it was still working at all! Many thanks DVA
Hello, The original battery costs approximately $150. Do you thing it worth it to buy the original please ? How many years do you thing we could keep the battery in a correct % health ? Thank you for your answer, and so great video by the way !
It is still in good shape/ use. To be fair, an after market battery would work just as good.
Just the thing I needed to see, was going to change fan motor after replacing 40a fuse, thanks
goeie uitleg dit filmpje. Zou het kunnen als deze stuk is dat alle standen wel werken, alleen als de sleutel uit het contact is blijft de verwarming doorblazen. Zit die stand 4 rechtstreeks aangesloten? Gaat wel om een auto verwarming, dus niet met de draaiknoppen
Dan zou je hem met een multimeter kunnen doormeten, maar als het door blaast nadat je de sleutel eruit haalt doet vermoeden dat het misschien toch een andere fout is.
Thanks for this! Just repaired mine after losing at least 2 pints from each barrel in dripping!
All ok and helpful, only one thing missing: the end of installation! Close te light box!! You forget it :)
You've got it right, i almost forgot it!
Great tutorial 👌 simple and to the point! I have my resistor now so am off to replace it 👍🏻 many thanks.
Many thanks for this. According to the manual there should be two clips but our car is exactly like the one in the video. The bulb and connector came out after going down a pothole Thanks once again
Just a ps, there are two t20 screws on either side and on our car they were too tight . Unscrewing them slightly allowed the connector to be located thanks once again
Thanks man, just saved me paying £18 for a 2 minute install!
Glad I could help.
Hi I had the same problem with the display not working, I replaced the three capacitors and the screen comes on for two seconds and goes out again, could it be the quality of capacitors?
It should not matter if it is of a bad quality capacitator, however cheap ones could have flaws.
Did you Disconnect the battery?
I did not.
When putting it back in, if it's a tight fit you may need to apply pressure to the metal wings of the holder rather than the plastic body to avoid too much strain.
Hi don’t suppose you could help iv done this and still have nothing I do hear it clicking any other suggestions?
Thanks for this, really clear.
Grazie
Thank you! This really helped out this morning :)
thanks - just what I needed. Now the job is completed the manual makes sense ....
A useful video but there are a number of important points. I have been given one of these machine to fix. Its totally dead. Back cover off. Remove the silver power supply and disconnect it from the middle PCB (black and red). The PSU is 10.5 volts out at upto 10 amps. I set up a bench power supply in place of the original PSU and pushed in the keg switch. Everything works as expected amd the supply indicated a 5 amp load with the pump running, and the fan going.. so turn that off and check the PSU. Dmm the outputs for AC and DC. TO to find a dropping dc voltage and no AC. So the psu is the problem. The thing is this is a switched mode power supply. They are simple enough and have common failures to look for. Hower. THEY CAN BE LEATHAL due to the stored energy and high voltages involved with them. The components replaced in this video are the output capacitors and they may be charged with enough to burn chunks out of tools. The input capacitor could have 400 volts across it and enough stored energy to stop your heart. This will be present after the mains supply is removed and you are now handling the board with the terminals exposed. If the switching FET has shorted you could get very high voltages on the outputs of the supply. Compnents may explode (capacitors usually do, especially if they are electrolytic and connected the wrong way). Also the heatsink can be a live surface at mains potential, especially if there has been a failure on board. Equally when reinstated an insulator shim may be missed. Do not try to repair any switched mode power supply unless you know what you are doing. It could easily be the last thing you ever do.
Well done ,thank you
thank you so much
Nice one needed this
Didn't see what direction you pulled tge bulb out. Probably the most important bit and we couldn't see it. 😢
Thank you! With this guide I repaired my Perfect Draft!
No way with dropping the fan motor down. Daft
Thank you!!!
amazing😍😍😍😍
Ik heb hem vervangen maar nu werkt hij nog steeds niet. Bij mij werken alle standen niet.
wery good 🤠
Pölysuoja jäi pois umpiosta
oops xD
Excellent help. Thank you.
Netjes! Leuk dat je het hebt gefilmd 😃
Can you show how to change the foglights? I want to change the old lights to yellow ones! ;)
Ti sei scordato il tappo di gomma..😃😃😃
Ben individuato! Ora è tornato ;-)
Great video thanks, I stripped it down but the capacitors do t seem the have blown. The unit shows power however when I press the two buttons to simulate a keg being in place the power shuts off
I have the exact same issue any fixes yet?
I’ve currently got the same problem. 🤷♂️
@@babychukka I fixed mine, not sure if it will work for you but here’s what I did. Take off the back exposing all the electronics. Unclip all the individual components ie the fan motor (there should be little push to connect clips. I then turned on the pump and pressed the two buttons where the kegs sits to indicate/simulate and keg in the device. I found that by doing this the display screen didn’t cut out like before which told me there was a fault with one of the components I disconnected. I managed to find out that it was the cooling plate section that was causing it to short out. Now, I’m not sure exactly what I did, maybe I mangaged to clean the electrical components of the cooling plate or merely by disconnecting and reconnecting some how reset it but it stopped shorting out after that. Worth a try at very least
this is perfectly done.- thanks! 👍🏼
Hola muchas gracias por tu video es muy interesante e intructivo .Tengo mi máquina averiada mañana lo pongo en practica pues me quedó un barril recien empezado
You don't want to waste a good barrel ;-) Have fun with the fix because the reward will be delicious :-D
@@DVAnl without a doubt you already know without pain there is no winner. Thank you
Thank you very helpful
Thanks for great vid!👍😊
Thank you so much for this video. After watching it I've changed successfully the bulb. I do have a question. Near that bulb are other two bulbs and I realised I have to change those also. Is the same procedure? The one you have changed is H7 12v 55w and I would appreciate if you could tell me the names for the other two. Thank you!
These are not the same procedure, al though the rubber housing works the same. Blinker light is just pull no twist same with parking light. High beam you have to remove the plug en push two prongs out. Blinker light H21W Lights H7-55W High beam H1-55W Parking light W5W Fog light PSX24W
Thank you very much! You have been very helpful. Your video is the best!
Thank you! 🙂
Did anyone resister smoke abit when they installed it ?
I don't think mine did.
Thank you!! You helped when every other video failed!!
No problem, some times I run into problems as well without a good video. So when I fix it I tend to make a video about it for other people!
Good video. Just saved me a lot of money - never changed one before and thought would be more complicated than that. Also thanks for the warning on not touching the bulb!
You're welcome and enjoy your new lights ;-)
Will you please upload another video showing us how to charge the battery for cp1300. And also how to fill up the ing when it's finished
I think you need to learn the difference between Repair and Replace...
Well I repaired the ventilator system by replacing the resistor. It also helps in the search query for other people trying to fix theirs.
Bit of a longshot but took the tap apart and I'm left with 2 pieces that don't seem to go anywhere after reassembly. Anyone with a complete breakdown of the tap would be great.
Hi CanaryIrish, go and buy yourself a (lotery) ticket because it is you lucky day! I found a French explanation for you about the handle. Haven't watched the full video but seems to have all the info you need. kzread.info/dash/bejne/gGeXpLVvnLOzqLQ.html Have a nice day!
@@DVAnl Super stuff. These things seem to get clogged with limescale and calcified. Stuck my one in a bucket with limescale tablets and it improved somewhat.
Just want to say THANK YOU this video gave me the confidence to look and sure enough my three capacitors had popped, so ordered new ones yesterday from amazon and fitted/soldered in today and it is all fixed - thank you again - prost
Hi Can you tell me the spec on the capacitors please so i can order ?
you saved my life!