Marine And Beyond

@graememckenzie66134 күн бұрын

Hello,I am wanting to know what diode goes on the vst fuel pump?

@KimDesruisseaux-in8hs21 күн бұрын

my engine starts and runs for about 15 minutes (when it gets warm) and then stalls with a code 91 "Fuel pump open circuit". Will this tutorial fix the issue? Excellent video btw.

@Rockers1121Ай бұрын

I have to clean the one on my 90hp evinrude etec ...

@RichardAnzianoАй бұрын

Hi, Many thanks for producing these videos. They are fantastic and easy to follow. I have a question on 9:12 of the video, I don't get any click nor is the brass plunger retained in the plastic. Would it still work or will it not allow appropriate flow back from the injectors. My motor was running rough and I thought it was that return filter but it was clean but when I went to check that one way valve the brass and spring wasn't retained in the grey plastic housing. Thanks, Rich

@GringoSFАй бұрын

60 HP e-tec engine will not start unless you unplug the fuel pump wire. then it will start up. Then plug it back in and it will run until you turn it off then it will not start up again until unplug the fuel pump wire. Anyone heard of this happening? I have new injectors, new fuel pump, new lift pump, new coils. all the voltage seam to be right oil pump is working. Anyone got a clue about this.

@cliveburgess41282 ай бұрын

I just finished putting a new pump in, couldn't believe the corrosion, etc. I couldn't have done it without this video, THANK YOU!!!!!

@jaymac102224 күн бұрын

What symptoms were you having to diagnose you problem?

@cliveburgess41282 ай бұрын

Great info once again, thank you!!

@Dobryi742 ай бұрын

Я из России. Спасибо вам за ваши советы. У нас в России очень боятся эти моторы покупать. Так как думают что ремонт сложный. Но с помощью ваших видео, это сделать намного проще. Большое спасибо вам за вашу работу.

@dgcarbust95123 ай бұрын

Exelente video 👍

@Dobryi743 ай бұрын

Здравствуйте. Как правильно устаеовить свечи, если электрод не напротив форсунки инжектора?

@peacefulrelaxationmeditati11124 ай бұрын

Very helpful, thank you!!

@jsandoval1534 ай бұрын

Hello ,my etec 90 engine shuts Down when the throttle lever is pulled back to neutral. The dealer replaced one inyector, but the problem came back. Now the dealer says I have to replace a second inyector. Is it posible that air is entering in the fuel hose, and is the cause of my problem?

@ayhankucukozer14786 ай бұрын

Hello dotum.. I wonder what exactly the small spring here does..

@orlandocajueiro29546 ай бұрын

Thank you very much for those tips. I’m facing a problem with 115hp injector. Do you think I can perform the same tests on the 115hp injector? Thank you again and congratulations for the video.

@ayhankucukozer14786 ай бұрын

I start the 30 hp engine and the engine runs at idle, but the engine lights do not go out. When I shift into gear, the engine stops.

@ayhankucukozer14786 ай бұрын

Hello.. The line coming to one injector of the 30 hp etech engine is not working. ecu is solid. There is a problem with the electrical installation. I wonder which cables should I look at? Can you please help?

@GringoSF7 ай бұрын

Hello boss, good video, I ask you, I have an evinrude etc. 90hp does not start and I get the code 94 - 29 - 117, what should I do? thank you

@ricardodantas36987 ай бұрын

Very nice video! Do you have a video like this but to replace and make maintenance in the Higth pump pressure in Evinruad 90 Hp etec 2011? Thanks in advance!

@Banda794948 ай бұрын

I saw your tutorial # 4 of fuel pump on a evinrude etec 30 hp Have the next problem: I have installed two Evinrude 30 hp engines (year 2019) Both with independent fuel tanks Since new about 200 liters of fuel comsuption During use al 4200 rpm , and aleatory, one engine or the other looses power to iddle (bur still running) Sometimes, just pull the throttle back and foward and get power again, sometimes , need to stop the engine with the key, restart and full power again. Have installed both independent external fuel filters with water tramp between original fuel tanks and engines What could be the problem? The no return valve? The Plunger with the float? the no return valve of air in the top ? Fuel vents on the tanks are ok Have to change small filters arround the fuel pump lines? Thank you for your advise Best regards Cesar

@Banda794948 ай бұрын

canot contact to your mail

@Banda794948 ай бұрын

Hi I saw your tutorial # 4 of fuel pump on a evinrude etec 30 hp Have the next problem: I have installed two Evinrude 30 hp engines (year 2019) Both with independent fuel tanks Since new about 200 liters of fuel comsuption During use al 4200 rpm , and aleatory, one engine or the other looses power to iddle (bur still running) Sometimes, just pull the throttle back and foward and get power again, sometimes , need to stop the engine with the key, restart and full power again. Have installed both independent external fuel filters with water tramp between original fuel tanks and engines What could be the problem? Fuel vents on the tanks are ok Have to change small filters arround the fuel pump lines? Thank you for your advise Best regards Cesar

@gabrielasule63019 ай бұрын

Seria posible mostrar donde esta el fusible? Where is the fuse? Thanks

@ayhankucukozer14789 ай бұрын

I just changed the fuel pump. I installed a new emm and it did not cause any errors. I think the EMM is faulty. The program on my computer is standard build (version 5.1.0).. how can I update this program. Can you send it to me via e-mail? can you help me.?. thank you very much..

@ayhankucukozer14789 ай бұрын

I just changed the fuel pump. I installed a new emm and it did not cause any errors. I think the EMM is faulty. The program on my computer is standard build (version 5.1.0).. how can I update this program. Can you send it to me via e-mail? can you help me.?. thank you very much..

@ayhankucukozer14789 ай бұрын

Hello friend.. 30 hp etech gives code 94 error. Excess fuel pump current detection. Can you help me? Thank you

@davesoltoggio328010 ай бұрын

My question is have ever tried to sonic clean injector? Then retest? 🤔

@javiervillacieros198411 ай бұрын

Hi. I saw your video and appreciate it. Thanks a lot.! I have two injectors from a 60 hp from 2016 and also two injectors from same engine but from 2006. Tested both and the ones from 2006 takes 18-20 strokes to fill and the ones from 2016 takes more than 60 to do... So. What should be the right amount of strokes here? Thanks in advance!

@roriemartin3430 Жыл бұрын

Is it defiantly a 3/8th bolt? It’s far too big! Looks more like 1/4 to me? Thanks

@centralscrutinizer768 ай бұрын

it is 1/4"

@ayhankucukozer1478 Жыл бұрын

hi..the gas pump of my enverude etsc 30 hp engine is constantly receiving electric current. The engine locks itself without starting. ecu is solid. how can i fix it..

@ayhankucukozer1478 Жыл бұрын

hi..the gas pump of my enverude etsc 30 hp engine is constantly receiving electric current. The engine locks itself without starting. ecu is solid. how can i fix it..

@ayhankucukozer1478 Жыл бұрын

Hello.. eteceh 30 hp petrol pump is working continuously, the engine is protecting itself, what should I do..my brain malfunction..

@ayhankucukozer1478 Жыл бұрын

Hello. We changed the e tech 25 hp petrol pump. but everything works normally, the energy comes, the pump works, but the engine does not start by gurgling.. we spray the cylinders with lining spray. Hello..

@FisForFishing777 Жыл бұрын

I have fault for open circuit #5

@FisForFishing777 Жыл бұрын

Would this test work on 250 injectors ? Or do I have to send it in for flow test

@user-of2hz9cg7u Жыл бұрын

Very informative very good video

@porcarinsorin594 Жыл бұрын

You have a video how i can install new injector ? Evinrude e-tec 25 hp , i buy one Cd whit softwere but i need help how i replace

@bobbyd41c Жыл бұрын

huge thank you for this video. it saved me from taking the boat to the mechanic. Installed a new simrad and when i ran the new transducer line through the hull, i pulled to hard and disconnected the private network in the motor. thanks to your video i traced it back to that and found it disconnected. simple fix but hours of BS until i found this video.

@ontariooutdoorsman Жыл бұрын

Excellent video. Thanks for making it

@coreyhubert1728 Жыл бұрын

Thank you!

@brianperkins6121 Жыл бұрын

Important note in your step by step for reassembly you forgot to illustrate the re-installation of the pressure relief valve assembly (I see it in place but you did not show its instillation) and tube after reinstalling the pump and screwing down its cover with the torx screws . while its obvious as one will have this part left over after reassembly , if you do not replace the fuel pressure regulator and tube Assembly you will have no fuel pressure to the injector manifold supply and the engine will not start or , start and run extremely poorly .. it is important to note the injectors high current electromagnet coils are cooled by the fuel as well as supplied with fuel. if the small mesh screen on the pressure regulator does gets plugged up, the fuel pressure will go way up and this puts the pump under a lot of stress, this also stops the fuel in the loop from returning to the Vapor separator tank so the injectors are not cooled as well as over pressured with throws off the injector charge calibration and makes the engine run rich ...

@ayhankucukozer1478 Жыл бұрын

hi..the gas pump of my enverude etsc 30 hp engine is constantly receiving electric current. The engine locks itself without starting. ecu is solid. how can i fix it..