Hi friend, same problem on an oled do you have any solutions? I am a technician if you can help me I would be grateful forever! 😊
@Skipperc3po15 сағат бұрын
nice video ... i prefer cables instead this adapter for the points
@trendingarena3855Күн бұрын
Another engineer did similar repair but he changed the HDMI ic, now i have ordered the ic to try repairing mine. How do I know the exact part to repair please?
@pcgamerracing55392 күн бұрын
hi when boot to atmosphare i get a fatal error occurred when running fusee.unable to identify package! press power to reboot. in 30.36
@wesleyportofilho3 күн бұрын
I have same orange screen, but i take off my wifi module, and still orange. After this, i put one wifi module from switch lite and still orange screen. What can be?
@rogergillette84263 күн бұрын
Why did I hear Dr. D from Phineas and Ferb at the hello part? 😅
@davideiannicelli82966 күн бұрын
Do you have any issues with online playing? lot of colleagues told me that for the offline gaming this is fine but when online you get instabanned. let me know cause you did an amazing job
@whoisme6786 күн бұрын
I think this has to be the VERY FIRST video I've seen which has given the voltages on the different areas of the board., so its A+++ from me.
@armaz8311 күн бұрын
I have this 2 sec blod after I replaced the psu. It was lightning that broke my first psu. Where can I find ppl in sweden to do this
@agowa33811 күн бұрын
Where do you get all of the testing point measurements from? I followed along however my RAM is ok (I think, it has higher resistance than your donor board but also not Samsung RAM, so that may be why?)
@amed32222 күн бұрын
Holaa a tod@s, Tengo una Nintendo switch que no enciende. La he desmontado , he medido voltajes y batería, carga perfectamente. Al conectarla al PC y con el programa TEGRA_RCM no me detecta nada., para que me salga "RCM device detected" , tengo que desmontar la EMMC, con esto montando no me detecta nada. Aun así, inyecto el payload desde el mismo programa a la SD, pero no hace nada, y sigue sin encenderse....Ayuda por favor!!!
@TheGamer50722 күн бұрын
how do you flash the chip?
@OwiPascual26 күн бұрын
is it okay if i didnt put uv mask
@OwiPascual26 күн бұрын
and what solder tip should i use
@pedrosolorzano589328 күн бұрын
Good video. Everyone just wants to replace things immediately without doing a little diagnostic work first.
@777MMC28 күн бұрын
By accident I dropped my switch lite and felf bad , what did he do put it in the grinder😅
@TabletOmegaElectronicaАй бұрын
Mi consola hace lo mismo, el problema es que no me accede a hekate. Creo que puede ser porque esta parcheada. ¿Hay alguna solución en mi caso?
@hove131Ай бұрын
What happened to your old shop?
@blackrockshooters645Ай бұрын
En mi opinión: awesome repair!! 😺
@royalmorphs2012Ай бұрын
Hi mate what size capacitor is it thanks
@mediaman3749Ай бұрын
Great video GREAT REPAIR as usual can I ask where you get your pads from Thanks Millenium Micro Repairs :)
@nixskups4788Ай бұрын
Hi, what is the temp. that you use for soldering?
@DillonShifflettАй бұрын
on 25:00 the big connecting point where the silver is ripped out the trace behind it does that big point goto the little dot to the left
@Temppy1Ай бұрын
what gauge wire is he using
@WorldWebMАй бұрын
Whats the use case of the relay reset? Why you need a reset anyways?
@sanketharekar9978Ай бұрын
I have similar problem though it starts sometimes. But when it goes for an update then it doesn't restart.
@benjieanunciacion9250Ай бұрын
Kalbo
@jeblimohamed6983Ай бұрын
Hello, thank you very much for everything you do I have a problem the device boots directly to the base system and does not enter the modified system The shape of the flashes of the LED lamp is as follows : kzread.infoO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_ Can you help me solve this problem? Thank you very much This is value multimetre Point D : 0.789 A : 0.645 C : 1.468 B : 1.402 3V3: 0.799
@craigreich8046Ай бұрын
What temp did you use to release and resolder the chip?
@TrinityCodexАй бұрын
whats that internal sd card thing?
@mrguru7738Ай бұрын
I installed a Hwfly but it blinks Blue, Yellow, Yellow and boots straight to OFW, any idea?
@ogaestАй бұрын
did you flash the HWFLY itself before installation?
@Deedee48-jg9omАй бұрын
I know this is a late reply, but my D point / CLK reads 1070 and it works perfectly. I tried it because I knew it wasn't grounded at all and it boots fine/all the homebrew functions work. What could cause this variance?
@MaynardOCАй бұрын
Very good and detailed installation. A question: what is the diameter of the copper cable used or what is the recommended one?
@ElSkeppo2 ай бұрын
Just seeing this video now as i read up on modding. One thing to note for future is that the launch option for CFW-sysMMC can lead to the switch being banned if it's not in airplane mode (Even when not connected to wi-fi) due to the way it communicates with the system NAND. CFW-emuMMC or stock - sysMMC are really the only 2 options that should be used, and quite a few people doing the modding service disable this before the user gets the console back to ensure they don't use it.
@twayne_21 күн бұрын
Thanks for the advice
@CallousCoder6 күн бұрын
If WiFi is not connected than it’s impossible you use a WPA protected WiFi. That’s the whole reason for protecting your WiFi
@joshmatrix12 ай бұрын
hi my up button on d pad shows allotted to zl when tested in diagnostic and in game play too works both the same whats the issue zl shows zl in diagnostic but up shows zl instead of up
@ayoungblenderprodigy67712 ай бұрын
Thankyou so much, great video, 1 tip for future viewers: when you place the new backlight led strips, make sure it alignes with the white sheet with the hole cutouts.
@barcelone9312 ай бұрын
hello does anyone have an idea of the value of the 4 capacitors in red thank you
@junimercs21832 ай бұрын
I’m on 17.0 now and I know there’s un update. Will these files and guide still work?
@Gamers-Ninety92 ай бұрын
Nice ❤
@JasonSmith-qx3zh2 ай бұрын
Freakin awesome when know how to do the do, 9 time out 9 problems will be solved 👍 ❤❗️
@icemanjt24302 ай бұрын
your hats pack isnt there anymore
@theoejoaquim2 ай бұрын
If I understood, if i lose my nintendo anyone who find it can create an account e reestart it ? Is that ? Tks
@ladislavoravec752 ай бұрын
Hello how much would u charge for this service please ?
@MicrosolderingRepairs2 ай бұрын
i have the same problem. blue light and 3 green lights. do i need to put a file into the chip?? all readings looks good, but i have black screen. It is Pico RP2040 v6.
@mohaptshoagong2 ай бұрын
can you be able to help with my Xbox one s?
@Metalliogre2 ай бұрын
What size of magnet wire are you using?
@msnygard2 ай бұрын
Is the standby voltage coming from the mailboard, or is is created on the powerboard?, i have a Philips philips 715g6973-p03-002-002m powerboard. the 12 volts are present, but not the standby 3.5/5 volr. grateful for any hints/tips :)
@waelshawkatezzat2 ай бұрын
My dear friend, I have the same problem that you started to fix. Can I fix it at home? What are the electronic parts that can help me fix this problem that you also encountered?
@jangshikkim40692 ай бұрын
thank you for great video. im trying to fix switch lite buttons that stopped working(- and screenshot, 2019 version that has a capacitor right above left joycon daighterboard) i tried replacing the fpc cable but problem exists. once when i left it fpr the battery to drain, those two buttons worked for a while but it is not working again. one more thing is when i enter hekate, it keeps taking screenshots constantly. any suggestions or measures i can take?
Пікірлер
Hi friend, same problem on an oled do you have any solutions? I am a technician if you can help me I would be grateful forever! 😊
nice video ... i prefer cables instead this adapter for the points
Another engineer did similar repair but he changed the HDMI ic, now i have ordered the ic to try repairing mine. How do I know the exact part to repair please?
hi when boot to atmosphare i get a fatal error occurred when running fusee.unable to identify package! press power to reboot. in 30.36
I have same orange screen, but i take off my wifi module, and still orange. After this, i put one wifi module from switch lite and still orange screen. What can be?
Why did I hear Dr. D from Phineas and Ferb at the hello part? 😅
Do you have any issues with online playing? lot of colleagues told me that for the offline gaming this is fine but when online you get instabanned. let me know cause you did an amazing job
I think this has to be the VERY FIRST video I've seen which has given the voltages on the different areas of the board., so its A+++ from me.
I have this 2 sec blod after I replaced the psu. It was lightning that broke my first psu. Where can I find ppl in sweden to do this
Where do you get all of the testing point measurements from? I followed along however my RAM is ok (I think, it has higher resistance than your donor board but also not Samsung RAM, so that may be why?)
Holaa a tod@s, Tengo una Nintendo switch que no enciende. La he desmontado , he medido voltajes y batería, carga perfectamente. Al conectarla al PC y con el programa TEGRA_RCM no me detecta nada., para que me salga "RCM device detected" , tengo que desmontar la EMMC, con esto montando no me detecta nada. Aun así, inyecto el payload desde el mismo programa a la SD, pero no hace nada, y sigue sin encenderse....Ayuda por favor!!!
how do you flash the chip?
is it okay if i didnt put uv mask
and what solder tip should i use
Good video. Everyone just wants to replace things immediately without doing a little diagnostic work first.
By accident I dropped my switch lite and felf bad , what did he do put it in the grinder😅
Mi consola hace lo mismo, el problema es que no me accede a hekate. Creo que puede ser porque esta parcheada. ¿Hay alguna solución en mi caso?
What happened to your old shop?
En mi opinión: awesome repair!! 😺
Hi mate what size capacitor is it thanks
Great video GREAT REPAIR as usual can I ask where you get your pads from Thanks Millenium Micro Repairs :)
Hi, what is the temp. that you use for soldering?
on 25:00 the big connecting point where the silver is ripped out the trace behind it does that big point goto the little dot to the left
what gauge wire is he using
Whats the use case of the relay reset? Why you need a reset anyways?
I have similar problem though it starts sometimes. But when it goes for an update then it doesn't restart.
Kalbo
Hello, thank you very much for everything you do I have a problem the device boots directly to the base system and does not enter the modified system The shape of the flashes of the LED lamp is as follows : kzread.infoO8dwRjmyKEs?si=zaDRE-_ccsvqzlR_ Can you help me solve this problem? Thank you very much This is value multimetre Point D : 0.789 A : 0.645 C : 1.468 B : 1.402 3V3: 0.799
What temp did you use to release and resolder the chip?
whats that internal sd card thing?
I installed a Hwfly but it blinks Blue, Yellow, Yellow and boots straight to OFW, any idea?
did you flash the HWFLY itself before installation?
I know this is a late reply, but my D point / CLK reads 1070 and it works perfectly. I tried it because I knew it wasn't grounded at all and it boots fine/all the homebrew functions work. What could cause this variance?
Very good and detailed installation. A question: what is the diameter of the copper cable used or what is the recommended one?
Just seeing this video now as i read up on modding. One thing to note for future is that the launch option for CFW-sysMMC can lead to the switch being banned if it's not in airplane mode (Even when not connected to wi-fi) due to the way it communicates with the system NAND. CFW-emuMMC or stock - sysMMC are really the only 2 options that should be used, and quite a few people doing the modding service disable this before the user gets the console back to ensure they don't use it.
Thanks for the advice
If WiFi is not connected than it’s impossible you use a WPA protected WiFi. That’s the whole reason for protecting your WiFi
hi my up button on d pad shows allotted to zl when tested in diagnostic and in game play too works both the same whats the issue zl shows zl in diagnostic but up shows zl instead of up
Thankyou so much, great video, 1 tip for future viewers: when you place the new backlight led strips, make sure it alignes with the white sheet with the hole cutouts.
hello does anyone have an idea of the value of the 4 capacitors in red thank you
I’m on 17.0 now and I know there’s un update. Will these files and guide still work?
Nice ❤
Freakin awesome when know how to do the do, 9 time out 9 problems will be solved 👍 ❤❗️
your hats pack isnt there anymore
If I understood, if i lose my nintendo anyone who find it can create an account e reestart it ? Is that ? Tks
Hello how much would u charge for this service please ?
i have the same problem. blue light and 3 green lights. do i need to put a file into the chip?? all readings looks good, but i have black screen. It is Pico RP2040 v6.
can you be able to help with my Xbox one s?
What size of magnet wire are you using?
Is the standby voltage coming from the mailboard, or is is created on the powerboard?, i have a Philips philips 715g6973-p03-002-002m powerboard. the 12 volts are present, but not the standby 3.5/5 volr. grateful for any hints/tips :)
My dear friend, I have the same problem that you started to fix. Can I fix it at home? What are the electronic parts that can help me fix this problem that you also encountered?
thank you for great video. im trying to fix switch lite buttons that stopped working(- and screenshot, 2019 version that has a capacitor right above left joycon daighterboard) i tried replacing the fpc cable but problem exists. once when i left it fpr the battery to drain, those two buttons worked for a while but it is not working again. one more thing is when i enter hekate, it keeps taking screenshots constantly. any suggestions or measures i can take?
Realy good jobe! tnx
Unbelievable work . Fantastic technician 🎉