Пікірлер

• 
  @ifubaraboyerowland8490Күн бұрын

  I like your video and I want to learn I like your explanations more but the diagrams are not clearly seen the background and the colour of the drawing is not distinct add colours

• 
  @Robert-qw7ex6 күн бұрын

  Can you do a video on derating so many people don’t understand it’s of the wire insulation not the device terminal ratings electricians don’t understand you can use the 90deg column when derating

• 
  @Robert-qw7ex6 күн бұрын

  Amazing video access to power is golden

• 
  @HICDIY13 күн бұрын

  Great

• 
  @RGL64218 күн бұрын

  Hello, I have wired my 3 phase motor per your video and used same components best to my knoledge, the issue I'm having is when I turn on my 120v brkr it pops. I looked over everything a phew times and can't see what's wrong. Any ideas. Thank you for your time.

• 
  @Penguin54521 күн бұрын

  Long story short multiply the gapping center to center times the shrinkage of whatever offset angle you are using, so 2 inch spacing with 30° offsets would have you advancing each mark a half inch on every pipe for your starting point. 🤘

• 
  @koarivera915121 күн бұрын

  Excellent tutorial keep up the great Work

• 
  @angelagilbert99526 күн бұрын

  Very well done!😊

• 
  @SimataMulenga27 күн бұрын

  Thank you

• 
  @burgessbrooks4435Ай бұрын

  Thanks for the video but let's save some time 1/2 tangent of your degree x gap of pipe. Add or subtract from your 1st mark depending on if it's the shortest or longest your starting with. Also this should work the same for kicks

• 
  @mikeyjay917Ай бұрын

  Is this the 2nd part of something? Where's the black wire come from why are there 2 reds and 2 greens? Those you've described well,but not the grey thing with 20+ places for wires to go

• 
  @mikeyjay917Ай бұрын

  Paint the edges of the feet on your stand white to match the rest

• 
  @JohnHelselАй бұрын

  great video!n

• 
  @svsoleil3255Ай бұрын

  I love this channel...great information and really nice/fun guys who know how to relay info...

• 
  @rockbottomiАй бұрын

  so in the angle pull we still had to size up the box to get 12 inches between raceway?

• 
  @ray603prospecting2Ай бұрын

  Greate video and explanations. By any chance would you be able to put out a bill of material on all the components you used in this video. I'm looking to wire my garage elevator in this manner. One switch downstairs one upstairs and one on the lift.

• 
  @connorchamsarian-soule1633Ай бұрын

  So I have a question, Why don't u have to account for the cross-section area when u put all the numbers in. Was it because it was already account for in the code book?

• 
  @wiliamcorrea9854Ай бұрын

  Good job

• 
  @MarcusAurelius-88Ай бұрын

  What app are you using sir?

• 
  @nickmedina3903Ай бұрын

  Should also make sure that your multimeter is rated for the voltage/ amperage you're measuring. If the multimeter isn't rated appropriately it could cause death.

• 
  @paulramirez17742 ай бұрын

  More videos please!

• 
  @onefixitman2 ай бұрын

  For the purposes of the viewer you should put a piece of blue tape on the motor shaft so we can see the motor reverse directions. Great video.

• 
  @seanb24912 ай бұрын

  By far best explanation

• 
  @rowellcanillo74692 ай бұрын

  Is table 8 is only applicable in DC system?

• 
  @johnhislopjr.74872 ай бұрын

  Ive had to check a lot of these. I would check the overload for tripping first. Then the 480 V fuses and then the motor for grounds. I found that rarely did the control circuit had problems.

• 
  @JeanpaulLapointe2 ай бұрын

  It's called motor pluging foward to reverse not a problem 21:10 21:10

• 
  @95ffd2 ай бұрын

  Great Video! What software are you using for your example?

• 
  @koarivera91512 ай бұрын

  By far one of the best instructors on KZread right now coming from a Utah Journeyman

• 
  @hetasarvaiya64432 ай бұрын

  Motor control forward start yellow stop off reverse green switch power teacher ji

• 
  @trade_design232 ай бұрын

  The moving photo of the women was distracting, childish and unnecessary. Just talk about the formulas. We don't need or want a show, we want an explanation.

• 
  @jameswright79602 ай бұрын

  Does anyone know what software is being used for the simulation?

• 
  @AccessToPower2 ай бұрын

  It is called Constructor

• 
  @jameswright79602 ай бұрын

  @@AccessToPower Thank you! Great videos by the way!

• 
  @hetasarvaiya64432 ай бұрын

  Timer motor power start stop off emergency reset teacher ji

• 
  @jsmithnevinsky2 ай бұрын

  ba- LA - kla - va

• 
  @mazmaz51362 ай бұрын

  SAME AS CEC CANAD CODE BOOK NICE

• 
  @davidhamilton27082 ай бұрын

  Making it easier s not a problem why don’t you show them how to measure for a concentric bend in the field

• 
  @johnsciarrone72452 ай бұрын

  Great video, however I have a suggestion. Use a digital protractor on the long side of the pipe , zero it, than after your first bend test the bent end for 30 degrees. Also note the spring back and write it down for the next guy. For example you might have to bend a 33 degree bend for a perfect 30. Thank you for your video.

• 
  @FRJ19822 ай бұрын

  When you were testing the power button, where dod you have your red meter lead?

• 
  @waywardson712 ай бұрын

  Great information and well taught

• 
  @pululunguente2 ай бұрын

  And what about you having 2 sets of conductors with Z method? Please Help!!

• 
  @joshleyba38542 ай бұрын

  I have 4 mixer motors at a WWTF. I have had to turn the yellow amp adjustment from 8 to 14 amps to keep them running with out tripping. 1 of of them however now runs for 1-3 mins then trips everytime. Pulled and megged motor. It is good. Voltage is good and consistent with other mixer motors. I have not seen Amps above 7 on anyof the motors including the one tripping. Any suggestions? Going in circles with Evoqua. Plant is 1 year old. All ran good first 6 months then developed issues after that.

• 
  @fuzzfacelogic7893 ай бұрын

  You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.

• 
  @AccessToPower3 ай бұрын

  The 10 amp relay is being used to on the control circuit of the VFD… not the motor circuit. The current on the control for a start signal is measured in milliamps.

• 
  @fuzzfacelogic7892 ай бұрын

  @@AccessToPower Please excuse my ignorance.

• 
  @AccessToPower2 ай бұрын

  @@fuzzfacelogic789 no worries. Thank you for watching and commenting on these videos. We created them to be helpful. Hopefully they accomplish that goal.

• 
  @diegojones24813 ай бұрын

  This guy explains everything so well

• 
  @tnr68983 ай бұрын

  You still need some electrical knowledge to understand this video. I know almost nothing and get lost after he adds the bridges. More detail on components is needed.

• 
  @hhr19853 ай бұрын

  I always teach to only swap A & C phase to reverse the phase rotation. This prevents accidentally burning stuff up in the rare time one may have to deal with the high leg on a 120/240 3 phase feed. (Code here is the high leg must be on B Phase)

• 
  @AccessToPower3 ай бұрын

  That is a good idea. Especially if the control voltage is 240 volt delta. But it is a good practice to teach newbies as it eliminates possibly making a mistake when the voltage, or high leg information is not understood or known. And yes, High Leg is most often on B Phase in the field... but there are some utilities that provide the high leg on C phase and it must be switched after the MSB to B phase on all Panelboards, and MCC's. This too can be a bit confusing and cause people to make mistakes. Thanks for your comments and sharing your best practices with the community.

• 
  @WestBuilt3233 ай бұрын

  4th year apprentice here , thanks for the smooth video 👌

• 
  @AccessToPower3 ай бұрын

  Glad the video was helpful, and thanks for commenting.

• 
  @Manchessollte4213 ай бұрын

  dude this is amazing, thank you so much. having an ACTUAL MOTOR is going next freaking level. thank you.

• 
  @AccessToPower3 ай бұрын

  Thank you. I appreciate the comment.

• 
  @123verne3 ай бұрын

  Why does the neutral have to go through the overload relay and not just straight to the coil (A2)?

• 
  @AccessToPower3 ай бұрын

  If the neutral went straight to the coil then the motor starter would never trip due to an overload

• 
  @123verne3 ай бұрын

  Ok thanks

• 
  @jesuspaz74463 ай бұрын

  AWSOME VIDEO

• 
  @AccessToPower3 ай бұрын

  Thank you for the comment! I appreciate your feedback.

• 
  @MIGHTYcbu3 ай бұрын

  The symbols we use in the Netherlands are so different, would've never recognized that to be a coil. And why over complicate it with the overload switches, that could've just been an add-on after you explained the circuit. The drawing is complicated to understand if you don't know what the coil does and how it is connected to the switch

• 
  @chainsawapple4 ай бұрын

  Thank you so much. Really helped me in my apprenticeship

• 
  @AccessToPower3 ай бұрын

  Glad it helped!