For motor controls I think this is the best channel on KZread. Your videos are thorough and very well explained.

@AccessToPower

4 жыл бұрын

Thanks Kenny W

@jeremyhall9346

4 жыл бұрын

May i also recommend BigBadTech chan. Jim Pytel is a great teacher aswell.

What a wonderful way of teaching. It has changed my learning experience. Keep up the good work and thank you for sharing all this information .

@frankvega93

4 жыл бұрын

Walter I have a MCH36 having problems to start

@frankvega93

4 жыл бұрын

Need support I am not familiar with this equipment the transformer burned and some bulbs

New at this, just moved from Maintenance Mechanic to Instrumentation and Electrical Tech., i struggle to understand how is it that the motor keeps running after the start button was let go. Saw this video and is very simple, Thanks A lot.

Excellent video Walter! I have been looking for hours for how to setup a remote start for a VFD powering a 3 phase motor on a table saw. Yours by far is the simplest, most straight forward with a clear explanation of how to do it using an Ice Cube Relay and the functionality of that relay. This video provides background support for your other video: "Starting a VFD with 2-wire Start". Thank You!

Definitely, the best site for controls.

I did learned something even being a Industrial Electrician years back. Id usually just use the start / stop etc inputs on the drive though. I personally never have wired a relay to drive like that before so it was a great vid.

thank you so much..im gonna look like a genius...you saved the day friend!!!

Great straight forward explanation Keep up the good work

Awesome videos! Thanks so much!!

Excellent Video.

Great content

Awesome!!!! Thank you so much!!

Amazing Thank you Sir.

Awesome explanation you should have a course online your step by step can’t be any better hope you continue making videos great job

@AccessToPower

3 жыл бұрын

Thank you Ismael!

Good job 👍 .. Learning in a steel mill.. seems overwhelming.. place is very loud in places and can't communicate while watching trainer.. Hard place to learn.

Excellent

Awesome! 👏🏽

I watched you video a lot

Instead of jumping wires it helps me better wireing like that

Can you wire to wire 2 wires from start to 2 and 3

Why doesn't the power from 1 and 3 cause a short against the line? Or maybe electricity doesn't work this way

@AccessToPower

3 жыл бұрын

If you look carefully at the schematic about minute mark 2:40 you will see that 1,2, & 3 all originate from the same source. Therefore they are the same potential.

Can you control a VFD with a start stop holding circuit and a field device such as a pressure switch?

@AccessToPower

3 жыл бұрын

Yes you could

Great work, what program do you use for your motor control simulations? Thanks

@AccessToPower

4 жыл бұрын

Stephen McAdam I use The Constructor software. www.cmhsoftware.com/constructor.html

@stevemc1

4 жыл бұрын

Thank you, love your work and videos

Hello sir will u plzz explaine me how i conect the solenoid valve timer to auto and manual starter

@AccessToPower

4 жыл бұрын

If I understand your question correctly, you should be able to connect a timer circuit in the same way that the float circuit is connected in the video link here. kzread.info/dash/bejne/Y35nmLWggKSodtI.html

What software do you use to make your videos?

Can you just run two wires to start

What software is your circuit drawing?

@AccessToPower

Жыл бұрын

It is Constructor software

?

You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.

@AccessToPower

3 ай бұрын

The 10 amp relay is being used to on the control circuit of the VFD… not the motor circuit. The current on the control for a start signal is measured in milliamps.

@fuzzfacelogic789

3 ай бұрын

@@AccessToPower Please excuse my ignorance.

@AccessToPower

3 ай бұрын

@@fuzzfacelogic789 no worries. Thank you for watching and commenting on these videos. We created them to be helpful. Hopefully they accomplish that goal.

Instead of jumping wires it helps me better wireing like that