Пікірлер

• 
  @ConfusedBirchForest-lo7jo21 сағат бұрын

  How far can you use it

• 
  @NEWTechCreative12 сағат бұрын

  I wouldn’t go any farther than 10m!

• 
  @jeffdeluca11534 күн бұрын

  When do you start selling kits? One of the nicest machines I've seen ANYWHERE!

• 
  @NEWTechCreative2 күн бұрын

  😄oh that would be amazing to be able to sell kits! Thanks for your feedback. I don’t plan to sell kits at this stage, however finalizing plans to release 🤩🤩

• 
  @jeffdeluca11532 күн бұрын

  @@NEWTechCreative was it expensive to have the plates manufactured?

• 
  @jeffdeluca11532 күн бұрын

  @NEWTechCreative Also, how do you figure out the lengths of the ball screws and linear rails? All In the design I'm sure. Do ball screws come in standard lengths that you design around? Thx again

• 
  @NEWTechCreative2 күн бұрын

  The total machine build is approximately 5k AUD$. It depends on where you can get plates manufactured and cost of this. I have put together a huge amount of build docs since my last video that I will be releasing soon and includes a build of materials list with links, 3D reference files and technical drawings. I designed the machine on readily accessible items that can be sourced anywhere you are in the world also provided options for plates that can be laser/plasma cut to allow different options depending what’s available. I have some testers helping me with fine tuning before release.

• 
  @TheDailyMemesShow6 күн бұрын

  New Sub 😁🎉❤😊

• 
  @TheDailyMemesShow6 күн бұрын

  By the way, this is wonderful workmanship. I have my reservations, however, when it comes to fixing them: Let's imagine one of the lights just got damaged, right? It'd be a pain in the rear end to fix it! Would you be open to the idea of the integration of *modularity* to have an unfair advantage when dealing with a broken LED donut?

• 
  @NEWTechCreative2 күн бұрын

  Thanks for your comment! I hear what you’re saying 😆 this would be annoying. The doughnut can be easily separated and replace as needed - although you have an interesting point regarding modularity!! Great suggestion 👍👍

• 
  @Erbsensuppe227 күн бұрын

  I'm motivated again to get my started project out of the basement. Thanks for the great video.

• 
  @NEWTechCreative2 күн бұрын

  Good luck with the build 👍👍🤩

• 
  @cpassuel985710 күн бұрын

  Nice design and impressive work

• 
  @AliHassan-yj9oy12 күн бұрын

  hey man great work. Can you please share more details about ULN2003 and how to wire it up, the wiring diagram you give is little bit messy.

• 
  @bora_13612 күн бұрын

  how much distance can that camera scan ? There are 110 horizontal and 75 vertical degree scanning in data sheet but I couldn't notice any length that identified

• 
  @NEWTechCreative12 күн бұрын

  I’ve texted outside and seemed to be effective within a 10meter distance!

• 
  @calinradu115 күн бұрын

  looks great but BUT , the music is sooo LOUD... fix that mate :)

• 
  @NEWTechCreative15 күн бұрын

  Thank you for your feedback!

• 
  @luisoquendo565616 күн бұрын

  thank you for sharing. I got a similar cnc and I would like to ask you if I can use GRBL in order to send the job to the machine. Thank you for any help.

• 
  @NEWTechCreative16 күн бұрын

  Grbl is the type of CNC processing language on these machines. You can use a range of programs to send gcode to control the machine such as Universal Gcode Sender, gSender, focus, laser grbl, candle, cncjs etc.

• 
  @XXhite19 күн бұрын

  Thanks for doing this video. For some reason, NONE of the other tech channels have done a review on these. And I've been wanting to know if they really work.

• 
  @NEWTechCreative16 күн бұрын

  No problems! They work great, just not great resolution 🤩 bang for buck

• 
  @AYUSHELECTRONIC-gr5po19 күн бұрын

  I want to play scrolling text in multi language wled how work. ?

• 
  @NEWTechCreative16 күн бұрын

  Setup as a 2D matrix and then select scrolling text effect! Check out the wled knowledge kno.wled.ge/advanced/2d-1d-Mixed-Setup/

• 
  @matthewjames751328 күн бұрын

  😎 awesome

• 
  @matthewjames751329 күн бұрын

  Thanks mate 😊

• 
  @arvandtiv3937Ай бұрын

  THANK YOU SO MUCH!!!

• 
  @ChristambarTrueManАй бұрын

  The machine looks great hats off your effort for putting it . May i know what will be the expected cost for build this CNC

• 
  @NEWTechCreativeАй бұрын

  Thanks for your comment! I am just putting files through the last fine tuning before release. I wish I could say a lesser price, however your looking at around AUD5K machine.

• 
  @ChristambarTrueManАй бұрын

  how can we build this cnc sir! is it open source or need to buy it from you

• 
  @NEWTechCreativeАй бұрын

  I’m trying to release in the next few weeks.

• 
  @RobertSalamunАй бұрын

  3d files for the donut led project? Available? Purchase?

• 
  @NEWTechCreativeАй бұрын

  Not at this stage sorry! 😞

• 
  @RobertSalamunАй бұрын

  All good just realized 12mm and the wires in between each pixel would be hard to cram it all inside the shell!

• 
  @richardmerifield3263Ай бұрын

  Thanks for the video. Love to see how well this can mill copper PCBs, any one tried that?

• 
  @NEWTechCreativeАй бұрын

  Absolutely perfect for PCB milling!! No problem with this machine 👍

• 
  @richardmerifield3263Ай бұрын

  @@NEWTechCreative Thanks. So have you made some pcbs yourself? Where is the best place to buy one from Aus? Cheers.

• 
  @NEWTechCreativeАй бұрын

  ​​⁠this is definitely a great little machine. Yes I’ve made a PCB with this. I also suggest purchasing a set of PCB endmills and 30degree vbit engraving bits to make PCBs. I think the best place to purchase from is Amazon Australia!

• 
  @roberthosking7524Ай бұрын

  I wonder if you could help me with my dilemma? I built a CNC Plasma table and control it with an MKS DLC32 V2.1 board (with built in Wi-Fi) and Open Builds Control (which I really like). OB will run the g-code file just fine as long as the plasma machine (pilot arc) isn't turned on. Once the plasma cutter fires the CNC machine freaks out and ends up either stopping with the torch still firing, or it takes off in some random direction - and OB responds with a lost port error and I need to reconnect. Obviously this is an EMI issue. I've tried numerous shielding, grounding, and isolation methods with no luck. However, if I load the g-code file onto an SD card, insert it in the control board's card slot, and run the g-code on the card from the "MK Laser" app on my phone, I can get a successful cut - but this also has drawbacks as the MK Laser app doesn't have z-axis control (I hear it used to) and the Z-axis height changes once the g-code starts to run. Messing with the MK Laser app to get it working this way is just a huge PIA and I would prefer to have the code being executed from inside OB. What I would like to try is controlling the MKS DLC32 board via Wi-Fi through the Open Builds Control software, but OB doesn't find the board when I scan networks. I've read in the forums that OB uses "telnet?" and would need GrblHal to be installed on the MKS board. I've also read FluidNC might work. But this is where things start to get over my head. Nevertheless, I'm convinced I could flash my board with either GrblHal or FluidNC (maybe even old ESP?) but I would need to get some very simplistic instructions on what steps I need to take to accomplish this. I realize a better card with ethernet or parallel connectivity would be a smart alternative, but I'd really like to see if I could get this card to pull it off. If you could assist me without boggling my mind with too much tech jargon (since I'm over 60 and this stuff will surely not attach to my brain neurons without many reiterations of the same info) I would very much appreciate it. For me simple is like this: go to ___ and find ___ and open it and then navigate to ___ and place it in ___ by dragging to ___ and then... After you do that then go to ___ and download ___ and then open the folder named ___ and then... etc. Thanks! Robert H. (a struggling newbie in the world of files and configurations and other seemingly complex operations)

• 
  @NEWTechCreativeАй бұрын

  Thanks for your comment Robert. This sounds like an issue I would love to help you solve, however this is not the right platform to assist. Discord would be the best place to help you with this: discord.gg/C64SwECE Otherwise email me on [email protected] Chat soon!

• 
  @munnakarthiko1Ай бұрын

  👏🏾😳💌🫡

• 
  @TrevorHammondsАй бұрын

  Your opening sequence is brilliant! You should consider making longer videos that are just like that. I'd love to add that to a playlist of music and art that I use as a screensaver and background music.

• 
  @NEWTechCreativeАй бұрын

  Cheers Trevor!! What a great idea 🤩🤩 I appreciate your feedback 👍👍

• 
  @viffs.3554Ай бұрын

  Great concept with the dust boot! I would like to give this dust boot a try, but the file I downloaded only contains the connection to the vacuum hose and the head, but not the connector you showed in the video that connects it to the CNC. Where is this located?

• 
  @NEWTechCreativeАй бұрын

  Thanks for your comment!! I’ll double check now… I may have forgotten to upload. It works ok- can definitely be improved 🤩

• 
  @NEWTechCreativeАй бұрын

  Send me an email to [email protected] and I’ll send you the file

• 
  @hudsongasparАй бұрын

  Thanks for the video. I need to change the standard engine ports for board development reasons. In this case, do I use the recording medium via the Arduino IDE?

• 
  @NEWTechCreativeАй бұрын

  No need to use Arduino IDE. To change pins, just change the yaml file for fluidnc and upload either by fluidnc term or the web ui 👍

• 
  @RootCNCАй бұрын

  Love it Myles! they all look incredible

• 
  @NEWTechCreativeАй бұрын

  Cheers Pete 🤩

• 
  @777smitty4Ай бұрын

  Thanks again for all your help.

• 
  @MrToporkoffАй бұрын

  Еще один сырой принтер, но ему это не простительно, цена слишком высока для этого. К1 лучше по соотношению цена-качество-возможности.

• 
  @777smitty4Ай бұрын

  Thanks for your reply. I have closed and reopened it a few times same thing needs internet. So do I understand correctly that that will not go away even if purchased?

• 
  @777smitty4Ай бұрын

  My question I downloaded rabbit just to try it when I open it it requires log in and internet connection is this part of purchased program or just the demo

• 
  @NEWTechCreativeАй бұрын

  Thanks for your comment! Yes just like other cad/cam software packages it will need to check for licenses, and logon via the internet for first time use to connect with rabbit cam data base.

• 
  @sourcerabbitАй бұрын

  RabbitCAM needs a sourcerabbit account and internet connection. The software is fully functional without paying for a subscription, except you cannot create gcodes.

• 
  @ad_deeppixelart5974Ай бұрын

  You have amazing skills!!! I am really impressed and your explanations are really clear : thank so much!!! Would it be possible to ask you questions privately about how I could improve mine please?

• 
  @NEWTechCreativeАй бұрын

  Thank you! More than happy to send you in the right direction. There is a huge community on Facebook or on the v1 forum who can assist, otherwise jump onto my discord: discord.gg/Ck4xXAWmQE Or email: [email protected]

• 
  @peacemakermotion3949Ай бұрын

  Very cool projects man. Love the look of them. Very unique.

• 
  @NEWTechCreativeАй бұрын

  Thanks dude! Have you got an update on your sim? Totally keen to test some super speed servos!

• 
  @thehangardesignsАй бұрын

  The intro is brilliant! The lighting, robot, music all worked so well! Keep up the cinematic work!

• 
  @NEWTechCreativeАй бұрын

  Thank you! 🙏

• 
  @tomnorman54612 ай бұрын

  ESP32 breakout board and the headers don't line up? What kind of CRAP is that? GARBAGE! UNACCEPTABLE!

• 
  @taxivideo2 ай бұрын

  J'adore !!!

• 
  @evri49072 ай бұрын

  can this cut carbon fiber sheets?

• 
  @user-xr3xy3tf1s2 ай бұрын

  Can I install multi-color printing here ?

• 
  @NEWTechCreative2 ай бұрын

  I don’t believe that the sk1 has a dedicated multi-color option at this stage!

• 
  @claritystatement95302 ай бұрын

  and did you have yyxza yaml file for tinybee cnc router

• 
  @NEWTechCreative2 ай бұрын

  There is a sample yaml file for the tinybee on the fluidnc GitHub and wiki. wiki.fluidnc.com/en/hardware/3rd-party/MKS_TinyBee

• 
  @claritystatement95302 ай бұрын

  hi how can i upload YMAL file to Tinybee controller?

• 
  @NEWTechCreative2 ай бұрын

  Feel free to check out my fluidnc video or ready the fluidnc wiki

• 
  @claritystatement95302 ай бұрын

  hi can you send me grble Pinout for the ESP32 thanks

• 
  @NEWTechCreative2 ай бұрын

  A quick google image search should lead you to the grbl esp32 pinout!

• 
  @parischantel092 ай бұрын

  Hi there! How do you center ensuring the engraving goes exactly where it needs to on the dog tag?

• 
  @NEWTechCreative2 ай бұрын

  Great question! Easiest way is to draw a box a tad larger than the item you want to engrave and place a waste piece of material down that you run a light burn of the outline, then without touching laser head, place dog tag in outline and place graphic inside box you drew and your good to go 🤩🤩

• 
  @parischantel092 ай бұрын

  @@NEWTechCreative awesome thanks for the tip. My laser will be here Sunday and I will give that a go. Appreciate it!

• 
  @yasinkolgu2 ай бұрын

  Wow! Thank you! Didn't know that stock to leave trick.

• 
  @matthewjames75132 ай бұрын

  Thanks for the video!!! in order to run the .nc file do i need to connect my computer and esp32 to the same wifi? Or can I run it by just connecting the micro usb from the esp32 to my computer? I've got all my .nc files saved on an micro sd card.

• 
  @NEWTechCreative2 ай бұрын

  Thanks for your comment! You can upload the .nc file over Wi-Fi to the Sd card (if you have on attached to your esp32) and run directly from the esp32. The esp32 doesn’t really like Sd cards any larger than 8Gb, but as long as it’s fat32 formatted and under 8Gb, you can plug in and read from file system via esp32. Alternatively you can also connect via usb and control using a g code send such as UGS, CNCjs or focus and not use the Sd card at all 👍👍

• 
  @matthewjames75132 ай бұрын

  @@NEWTechCreative Thanks for your help and sorry if these questions are really dumb - I'm just getting started. So far I've noticed I can only run the .nc files when I connect my computer and esp32 to the same wifi. Strangely, when i connect directly to the fluidnc wifi or just plug my computer to the esp32 via micro usb I find I can jog the machine, but I can't run the .nc file. Not sure why this is the case. In all cases I have the .nc files stored on the microSD. Regardless, if i understand you correctly I can fix this by installing a g-code sender like CNCjs on my PC. But in this case, won't I still have the same issue? Once the g-code sender sends the .nc file to the fluidnc firmware, then will it run?

• 
  @NEWTechCreative2 ай бұрын

  Hmmm sounds strange indeed! It’s difficult to say and would be better to see a video of what’s happening. If you in discord, feel free to jump on to the fluidnc discord and ask there or more than happy for you to jump onto my discord to sort out. discord.gg/MYXurYv2

• 
  @vigigamehacker1232 ай бұрын

  Every shot is so 'cinematic' that you cant see wtf is going on at all, I just want to see where/how the rails are mounted, whats the ball screw block positioning etc. etc. but I feel like im watching a teen drama series

• 
  @NEWTechCreative2 ай бұрын

  Hmmm happy to share more detail. Hard to see how it is relatable to teen drama series, however I suppose it’s not bad 0 budget and 100% passion. Feel free to jump onto my discord and I can provide more detail.

• 
  @nandusinganamala20602 ай бұрын

  this is awesome, thank you !!!

• 
  @FlixmyswitchLASER2 ай бұрын

  I seen some video where a TFT screen works but the poster gives no info. Does anybody know how it's done

• 
  @NEWTechCreative2 ай бұрын

  There has been no official release for this support, however people have been tinkering in the code to have some ability to work. If they haven’t shared the code, it probably because it was not stable. For info about implementing this type of code or reasons for no support check this out: wiki.fluidnc.com/en/hardware/pendants_displays

• 
  @zbigniewkindlarski81522 ай бұрын

  wow

• 
  @sannyassi732 ай бұрын

  Nifty machine! Can you add a spindle/router and CNC wood? You've got a vacuum so I assume so, would have been nice to see that in action. It's a really clean system!

• 
  @TheRainHarvester2 ай бұрын

  😢lots of potential points of obselescents : wifi router, windows proprietary upload software....

• 
  @mattivirta3 ай бұрын

  only what i need my DIY machine have this biggest and better spindle. all other have same, motors, but i use DM 556 drivers can use biggest possiple nema 23 motors. and i use old cheap paraller port 10$ controller board, cheap and can use 2 paraller port easy, usb port controller have all too lot problems and not can use safety REALTIME controller. mesa card whit ethernet have perfect but too expensive hobby user and DIY builders.

• 
  @NEWTechCreative3 ай бұрын

  Nice! Yes the 2.2kw make a huge difference! So many options for controllers these days!

• 
  @mattivirta3 ай бұрын

  i made under beam led light similar but i use ready to use aluminium U-profile were have channel bush in led. light strip and top profile have diffuser plastic. cost 4$ only/meter , and easy install some screw to beam.

• 
  @NEWTechCreative3 ай бұрын

  Thanks for sharing! Yes this is definitely an easier option 😂😂 I often reinvent the wheel 👍👍

• 
  @mattivirta3 ай бұрын

  RGB leds have totally waste only time and money, not sure need anywere, have nice if have many colour leds but not need newer whit cnc machine. waste lot time stupid.