Пікірлер

• 
  @Mytube-15 сағат бұрын

  how can i talk to you,i have almost same problem,bottom flash red but all my dash light turn on

• 
  @AbeVicious19 сағат бұрын

  Man, crazy that this trick goes unnoticed lol

• 
  @ImpanoBrice22 сағат бұрын

  You are intergent

• 
  @WilliamsonBrianКүн бұрын

  man i took mine apart probably wont be able to get it back together lol

• 
  @harryjones5159Күн бұрын

  Hey great vid, im currently doing up a 309 myself It was cranking and now I just get a clicking sound. Do you have any idea what the cause of this may be ? also I am trying to locate the fuel injectors in the engine could you point me in the right direction where they may be. Thanks

• 
  @fanueladebayor95532 күн бұрын

  Please can I have your WhatsApp number i have same fault the engine battery completely drain after a little ride i noticed the battery is not charging when you start the car and disconnect the battery terminal it goes off

• 
  @Henry-be6zg2 күн бұрын

  Great Instruction ! & Instructor ! Thank You Friend ! "😁👍"

• 
  @Max_Chooch2 күн бұрын

  So that's why my axle rattles down the dirt road. Spent ages trying to figure I out until one day I just grabbed the axle and wiggled it. It still works fine, but my guess is that brass bushing is fked.

• 
  @josephgumlaw26692 күн бұрын

  Would it be worth changing the clutch then to change the whole compressor?

• 
  @JDzAlive4 күн бұрын

  Alldata was virtually useless for my 1997 Nissan truck so it was canceled pretty quickly. Wasted money.

• 
  @eoghanhennessy4434 күн бұрын

  Thank you for making this video

• 
  @eoghanhennessy4434 күн бұрын

  This mad i have a golf r driving me mental hope this is my issue

• 
  @knockywigglesworth19095 күн бұрын

  Eco BOOM 1.5L a couple hours diag time exceeds the cars value. Quality is JoB NONE! Have you driven a Ford lately!

• 
  @antonioflores79975 күн бұрын

  I have an issue with my newly bought creader 3001 obd2 when plug to dlc port of my car nissan almera 2016 message appear Communication Error. Please advise what to do.

• 
  @edc94425 күн бұрын

  Just repaired my AC thanks to you!!! Thank you for a clear video. Appreciate the work you did

• 
  @BDI015 күн бұрын

  Worked like a charm on my 2005 2500 Duramax, thanks for tip!!!!!

• 
  @meblake73597 күн бұрын

  Do u have to have autoauth for chryslers 2018 and up or can u use a 12+8 connector?

• 
  @mikejr5508 күн бұрын

  Great video. Thank you for showing how to use these features.

• 
  @blazindragon2968 күн бұрын

  its funny every technician i know or have seen on KZread has that same hammer as I do. I just did my 03 Tacoma and my god it was in there i did everything possible. finally decided to cut the U-joint out with a cut off wheel and then hammered out the caps with heat.

• 
  @user-mh4rj4pg9t8 күн бұрын

  Bro I can’t believe what I’m watching there is no way you’re getting that thing running again. I don’t even know where to begin. No labeling, no proper diagnosis, what if the customer couldn’t afford extra work, dropped the timing guides. Unbelievable

• 
  @ThePracticalMechanic8 күн бұрын

  🤣 I’ve had dozens of these apart and often reassemble them after someone else has taken them apart. Vehicle was indeed reassembled and ran fine. Just because diagnostics wasn’t performed in this live stream doesn’t mean that diagnostics wasn’t performed.

• 
  @philradke58319 күн бұрын

  Still the most helpful explanation out there! Best Father's Day present 😂

• 
  @alandust21889 күн бұрын

  I've watched several videos on u joints....yours is by far the best. THANKS

• 
  @lukas______9 күн бұрын

  Would a generic j2534 cable that plugs into a laptop with pirated SSM4 software work to program keys on a 2015 outback you think?

• 
  @ThePracticalMechanic9 күн бұрын

  I’m not sure if that would work or not. It’s possible. I know that the newer push button start models require an online connection and server key so you would likely be limited on newer vehicles. With non-genuine software there is no guaranty of any function working properly.

• 
  @William511159 күн бұрын

  just take all the wafers out except 1 or 2. car will still work fine no one will ever know

• 
  @William511159 күн бұрын

  I ran into this problem before. most likely they had a really heavy keychain with lots of keychains. tumbler got worn out from all the weight

• 
  @francisconevarez878812 күн бұрын

  Great info, helped me out a lot, thank you

• 
  @lornafulsom2112 күн бұрын

  Im sitting in my car with it refusing to start - the ignition doesnt seem to connect + although it seems tohave power. We tried to jump it but my friend said you have power to everything so its wierd. Just random all of a sudden I ve only had the car a month and everything was good or recently done (beaides needing a new cluster which i new and found at a pick and pull to go maybe pock this weekend) so Before calling a tow truck i goggled the issue to see if it was related to cluster and found you. Im hoping it might start again if i leave it over night to get me to a shop tomorrow and im going to recommend to them yr video. Hopefully i can afford to fix it all now thst you sepent the investigation time. Thank you

• 
  @frederickwoof578513 күн бұрын

  You could put bearing cups into a freezer, if your quick to install them. Put a heat gun on diff. housing as well.

• 
  @cateyparr105416 күн бұрын

  Follow up video????

• 
  @rivkag466916 күн бұрын

  Thank you Joe and the Practical Mechanic!! I think this just might be a fix! Did this yesterday to 2018 Crosstrek Premium, code P00019 that came on with a delayed oil change. Spent lots of money having a mechanic change cam oil exhaust solenoid, then stated didn't know what else to do. Took it to a Subi private mechanic who scoped and state absolutely everything in the engine is working as it should be but could not get the code to re-set. Used a ThinkDiag2 with iPhone, have so far driven 3 times about 15 miles total, power in lower gears is restored and no CEL light!!! The Subaru XV forum has deets on this but, if anyone is wondering: use your 30 amp spare fuse (in the lid of the fuse box) and your grey fuse puller (middle of lower row in fuse box). The test fuse open spot is the far left lowest (closest to you) spot. Thank you, thank you, thank you Practical Mechanic!!!!!!

• 
  @rubenrojas593916 күн бұрын

  I from venezuela, gracias.

• 
  @rubenrojas593916 күн бұрын

  change this integrate and dont power.

• 
  @rubenrojas593916 күн бұрын

  Found 1 integrated bad, is cuadrate of 64 pines.

• 
  @rubenrojas593916 күн бұрын

  Hola, friend. My trouble is, no power my cluster,

• 
  @therealdeborarogers16 күн бұрын

  Thank you! You gave me all the info I was searching for.

• 
  @AriasElectronics17 күн бұрын

  Good job!

• 
  @starke666617 күн бұрын

  Thanks Broski. Awesome video. I just did mine.

• 
  @jasonroberts224918 күн бұрын

  This guy did it in four minutes; between ordering parts (including the hub blaster tool) and whacking with a sledgehammer after spraying with penetrating oil it took me a week.

• 
  @Ozarkwoods14 күн бұрын

  That’s horrible I am on 4 hrs and the hub is separated on my 17 Outback when I used the slide hammer. Now I have to take off the rest😢. Not a fun task I am looking for that miracle tool.

• 
  @billkerr170418 күн бұрын

  Hell yes good vid bro

• 
  @lst_lt_dann892318 күн бұрын

  Holt smokes, this fixed my issue too! 2017 Toyota 86 (brz) with a stuck p0018 code after a timing chain replacement. I used an Autel scan tool and I'm 100 miles in with no pending codes! Thanks a lot for making this video!

• 
  @ThePracticalMechanic18 күн бұрын

  Tell me more!!!! Several have reported that it doesn’t work on the BRZ. Did your BRZ have the inspection mode fuse slot? I don’t have easy access to a BRZ for testing.

• 
  @lst_lt_dann892318 күн бұрын

  @ThePracticalMechanic yes, mine had an inspection fuse spot. It's not labeled on the diagram... but as soon as I found the correct spot, the fans came on just like in your video. Then we followed the steps to a T and it changed my VVT's back to zero. The car is a 2017 86 (brz) 6m with a supercharger running an e85 tune with ecutek. I was worried about changing the ecm and losing tune. This solved the issue. Does the ecutek tune change anything? I don't know...

• 
  @CasperVsTheWorldGaming15 күн бұрын

  @@lst_lt_dann8923 Hey there LST, i have the same issue, are you able to let me know what inspection fuse spot you used, cause i am lost and have no idea where it is on our cars.

• 
  @CasperVsTheWorldGaming15 күн бұрын

  also can you let me know what autel scan tool you used?

• 
  @lst_lt_dann892315 күн бұрын

  @CasperVsTheWorldGaming it's right in front of the 30a DCC fuse. It's x'ed out on the diagram. The fans will run when you turn the key on, that's how you know it's the right one. As for the scanner, I'll have to get back to you on it. It was my cousin's scanner and I didn't see a model number on it.

• 
  @djtjsommer4218 күн бұрын

  Also I don't have no lights on the dash that are "out" but they are din. ??

• 
  @djtjsommer4218 күн бұрын

  Great video....I to own a doge 1500 STI Hemi. It runs fairly well with 237k miles om it! but I'm getting around 9-11 miles a gallon with no load on the high way!!!!. I also always use top grade full so just figuring out the best next step. Thanks, Tj

• 
  @master025519 күн бұрын

  I had the same issue before with my 2012 impreza. I got a good/used original soleniod from ebay for CAD$200. Bought the gaskets and o-rings from the dealer for another CAD$150 and its been working without issues ever since. A new valve body + install is CAD$2500 from the dealer.

• 
  @fisherguy19 күн бұрын

  What year was that truck? My 08 has had this problem, had the alcohol levels reset but I still get the code now and then and when I do I use my tuner to clear them. One symptom I've noticed is the tranny shifts hard when I have the code. What can I do to cure it permanently?

• 
  @ThePracticalMechanic19 күн бұрын

  Depending on the tuner you can turn off flex fuel entirely. Some have an option to turn it off and some require you to edit the maps from the ecm. You might be able to request a custom tune from the device manufacture. You may have something else causing the lean condition that is the root cause of the flex numbers rising. Check for Vacuum leaks when cold, clean mass air flow sensor and throttle body and see if the problem is resolved. Toyota has the same issue from the tundra and sequoia and it is caused by a weak fuel pump. The pump may deliver too little volume on cold starts which leads to falsely assuming the presence of flex fuel.

• 
  @fisherguy17 күн бұрын

  @@ThePracticalMechanic, interesting. I cleaned the MAF anf throttle body the 1st time I had the codes again, didn't help. I had the alcohol levels rested about 18 months ago and since then I've had them come back, first for 1 bank then if I leave it for both. I've just been clearing them with my 'superchips' which clears the code and fixes the hard shifts. Frustrating, hope it's not the fuel pump, PITA to change.

• 
  @inspectorlunge388719 күн бұрын

  Cars should not be this much for trouble to repair. Come on America! You can do better! Start using your brains and stand up to politicians and corporations trying to make your life harder! This is just going to keep getting worse and worse because people just let them get away with it.

• 
  @andrewweiss970020 күн бұрын

  I need to know how to do this with the autel on a 2017 BRZ, I hear it also can be done, I replaced the bank 2 intake sprocket. Letting RTV set up, Getting ready to start. Any help thanks!

• 
  @ThePracticalMechanic20 күн бұрын

  Brz cannot be done with scantool as far as I know. I do t have access to one for testing so I cannot confirm. I think the brz/FRS need to have the eeprom manually edited.

• 
  @Robertfixes20 күн бұрын

  Im working on a 58 Bel Air that i removed the blue flame inline 6 wondering if that 60 that your working measure as wide as the 58 ? Was planning on using the trunk manifolds ? Thanks for all the info !

• 
  @RalphMartinez-mz7ev21 күн бұрын

  2004 VW Passat GLX Sedan V6 these steps worked for me to add a second key, but how can I program out other lost key fobs or how can I add my 3rd? thank you in advance

• 
  @ebrd4422 күн бұрын

  Worked perfect! 2001 Tacoma. Not a single drop😮.

• 
  @Betta_Repairs-kz6rq23 күн бұрын

  Nice Video. Quick question about this subscription. Can I change vehicles. Can I do a vehicle this month and next month change it to another vehicle?

• 
  @ThePracticalMechanic23 күн бұрын

  You would have to buy a new subscription for the new vehicle. The only way to have all the vehicle available is to have a shop subscription which is around $200/mo and requires a business license.

• 
  @Betta_Repairs-kz6rq22 күн бұрын

  @@ThePracticalMechanic ok thanks.