Пікірлер

• 
  @pocketgools3194Күн бұрын

  Saw you at flite fest, and the mustache was awesome. I wanna get into bigger quads. I have the beta fpv Cetus pro, which is just the mini whoop, but I want to fly outdoors more. I also don’t want to break the bank. What are your suggestions, or a video I can watch?

• 
  @RCwithAdam121 сағат бұрын

  Hey thanks! Say hey next time and I'll give you a sticker! I don't have any specific models in mind, but I would say something in the 2.5-3.5" prop size range would be a good place to look. The smaller size usually means less weight, which means less likely to break, and the batteries will be smaller and cheaper than for a 5" size quad.

• 
  @norcal_voodooКүн бұрын

  Thank you for this awesome video. Super helpful 👌 👍

• 
  @userTJ397802 күн бұрын

  @4:18, that happened to me on Saturday afternoon; chasing the "chosen" plane, I got brutally smacked by another chaser and my Ugly Wonder went down hard!

• 
  @userTJ397802 күн бұрын

  Hi Adam, this was one of the only Flite Fests I had to miss in the last 5 years, but I was there as long as I could be this weekend (6/22-23, 2024). Thanks for posting!

• 
  @benjaminal-doory18172 күн бұрын

  I'm the guy in the thumbnail for this vid. I know because I was the only guy in 2023 using an FM radio. And I have that shirt.

• 
  @EMDRONES2 күн бұрын

  Does it fit in carry top shelf on planes ??

• 
  @RCwithAdam12 күн бұрын

  I haven't tried it, but I expect it will since I could still (just barely) fit the larger pyrodrone backpack into the overhead on smaller commuter jets.

• 
  @MeBoazz2 күн бұрын

  I want to get that bag so badly. The only bag I have is a 40L one from temu =(

• 
  @RCwithAdam12 күн бұрын

  It's worth it! I would email rotor riot or keep checking to see when it's back in stocks. Or maybe they'll just come out with a version 3.

• 
  @lesconseiles98782 күн бұрын

  Quiet fpv drone

• 
  @net69flix2 күн бұрын

  how can i increase the volume of the timer?

• 
  @net69flix2 күн бұрын

  awesome thanks, i will be setting that up on my tx

• 
  @amrv80643 күн бұрын

  I have ffollowing problems 1. Transmitter doent show output mode 2, i accidentally soldered i bus input to sbus pad in FC will it ruin my fc 3. Channel mappin in Beta flight isnt working Please help me out

• 
  @serenestateofbeing10623 күн бұрын

  The "low" one on the left in the thumbnail is as high as i can get mine 😂

• 
  @ajuwinfly82723 күн бұрын

  Hello this receiver suport F4 v3S flyit controller board ?

• 
  @superbadmofo13 күн бұрын

  Killer video man, Adam thanks alot for clarifying those concepts.

• 
  @user-vi6kk1sn1x4 күн бұрын

  ASMR 😀

• 
  @johndamascus26344 күн бұрын

  I'm looking over at my Phantom 4 now...

• 
  @heklik4 күн бұрын

  How many grams is the servo ?

• 
  @zakariyarahman23004 күн бұрын

  I just ordered the flysky i6x transmitter off of Ali Express. For $26.00

• 
  @vax_ta4 күн бұрын

  hay bro , please buy silent board for ur printer 😂😂which one is it? I have ender 3 pro and 1 week ago I replaced to silent mb and my ears stopped bleeding 😂😂

• 
  @copyandpastification5 күн бұрын

  nope, i tried everything with Fs-i6 and a fs-x6b receiver with INAV (f405 wing miny - speedybee).... any advise?

• 
  @sparrowww_6 күн бұрын

  when i uploaded the file and started printing, it was off centered?? i don’t know how to fix it. i have a bambu lab a1 mini and when i try to move the project it just says “off centered.” the project stays in the center for the file, but it’s off centered on the printer.

• 
  @Quad8ightMix6 күн бұрын

  Nice axii, can you also share what's the brand of the printed facial foam from your Dji goggles?

• 
  @streamylc6 күн бұрын

  Shout out to Flight Fest

• 
  @twindaddy82917 күн бұрын

  How do u have the goggle angle view..wjat do I need to get 4 my quad to look like this..please tell

• 
  @twindaddy82917 күн бұрын

  U need to put a cape on it😂👌🤟🤟🤘🤙👍👍.love ur vids..

• 
  @matty28087 күн бұрын

  Hey, how did you get rssi working on fly sky in this video?

• 
  @InfluxFPV7 күн бұрын

  If you fly 3D, you can still use the app, but do not use it to spin motors in ANY way, it doesnt understand and will full throttle your motors until the app is disconnnected, and not just closed, the full BT connection or usb

• 
  @RCwithAdam17 күн бұрын

  Thanks for the tip!

• 
  @richardlitt64167 күн бұрын

  Adam - my name is Richard Litt. My previous rc experience is 30-size fuel rc Helicopter - I flew many years - my flying background was mostly level, no 3D. I sold my helicopter to get into 5" 4s lipo battery drone. I am using Liftoff simulator to learn how to fly my drone. I plan on flying LOS (similiar to my RC Helicopter flying) so i modified my drone (Nazgul5v2) and removed the antenna and replaced it with a 50ohm load. The lessons on-line are very helpful (RCwithAdam). I appreciate the Rate descriptions. I have some comments regarding beginner pilot drone control: 1. I started to fly in Acro mode 2. At the end of Lesson 2 you commented on being in Acro mode require corrections - i detected right or left drift as soon as i gave throttle. I have to correct this drift. 3. Most of Lesson 2 is in Level mode which does not require to correct drift corrections. 4. What is your opinion on staying in Level mode or Horizon Mode until i can switch to Acro Mode? I do not know how long that will take. I will not give in - fun hobby - I am a retired Aerospace Electronics engineer so i can deal with learing how to fly a drone. I can be reached at [email protected]. Thanks

• 
  @bilyferrache7 күн бұрын

  Merci pour ta vidéo Ça m’a aidé

• 
  @goldsilverjunkie8 күн бұрын

  I went on the auto desk website and it doesn’t have fusion 360 a it haves is fusion

• 
  @charmontravel8 күн бұрын

  This. Is. AWESOME!

• 
  @oscillationandy69238 күн бұрын

  That's the Reptile Cloud 149 cinewhoop frame. One of the few frames Catalyst Machineworks sold that wasn't their design. It's the smoothest flying quad I have. Like butter floating on the wind. Check your PID tune....

• 
  @oscillationandy69238 күн бұрын

  Add get rid of those shitty emax motors. Solve some issues right there...

• 
  @americanindeon8 күн бұрын

  Thanks mon!

• 
  @dontbanmebrodontbanme54039 күн бұрын

  I just got my Bambu Labs P1S today. This video was very helpful!

• 
  @RCwithAdam17 күн бұрын

  Have fun!

• 
  @richardpendley34549 күн бұрын

  TO RCADAM: PLEASE READ !!! hey I've been looking for a video on KZread where someone upgrades the mini 2 se and others upgrades the mini 2 se motors with 2212 920kv brushless motors or just your regularly sold diy fpv drone motors please do a video where you take a dji drone leave everything the way it is except replace the motors I wanna know if it will work ok cause I want to do it to mine ! K thank you hope you see this !

• 
  @RCwithAdam18 күн бұрын

  Good Idea. I've been wondering the same.

• 
  @R.B_B9 күн бұрын

  Really nice

• 
  @Marvel_gaming_Tamil10 күн бұрын

  Bro create more cracy videos love from India

• 
  @NataralDeez10 күн бұрын

  is this for resin or fdm

• 
  @kjamison595110 күн бұрын

  Thank you for this. The UK site sucks and its way more difficult to find this download. EDIT: My OS no longer supports the latest version of Fusion and there's no way to upgrade the OS without buying a newer computer. I don't have the money for that.

• 
  @RyanCool111 күн бұрын

  Thankyou, this helped me a lot

• 
  @RCwithAdam18 күн бұрын

  Glad it helped!

• 
  @802Garage11 күн бұрын

  This seems like a pretty cool filament. A shame it's essentially unavailable currently.

• 
  @G3N0C1D3R11 күн бұрын

  How do you move the whole plane? I noticed u can add health to the parts and I want to make the whole aircraft invincible (still explodes on impact) but the thing is it’s all downloaded aircraft’s so I don’t want to piece by piece increase the health

• 
  @stewartabel11 күн бұрын

  Hey this was really useful as im building the Chimera7 V2 and it came supplied with the longer cable, was unsure how 'tight' the fitting of the cam wire to the unit was, i see you also were not too convinced of the connection but indeed the little cover presses it down nicely. Thanks again!

• 
  @steveengelmann851813 күн бұрын

  I feel like this is more stable against turbulences then a commercial airplane. Would like to see tests somehow.. but dont even know how you would test for that.

• 
  @demonhogo13 күн бұрын

  3 orders and you could buy a printer for the same price

• 
  @drowsygators14 күн бұрын

  like how the Transmitter has Labels but i cant find a transmitter with easy/quick labels within my budget

• 
  @theginypig270514 күн бұрын

  this is crazy looks like a game!

• 
  @lambo_drives14 күн бұрын

  3:36 race stance take off - sweet. 5:33 what a perfect leaning pole ✌🏻

• 
  @dannielsawulski122115 күн бұрын

  Is it safe to spray silicone on outside of electrical connector and on wire insulation? For automotive applications.

• 
  @bluecavemen15 күн бұрын

  This maybe off topic or not I’m not sure. So I’m using this remote and a 10ch receiver. Now what I’m trying to do is use a hoverboard to turn into a lawnmower. I saw a video how connect and add the firmware. The firmware is for AUX I have it connected to ch1/ppm. On the right stick. (Left and right ) It makes the wheels go forward and backwards I can see the wheels spinning. But I don’t see the wheels moving left or right. I try moving all the stick every direction. I’m starting to think I need to do something in the settings so the right stick goes up or down to move left or right or the left stick does that either way I’m lost and not sure what to do