In this channel, I will show you how I went from one free broken generator to buying my dream motorcycle. Here you can find tutorials on common issues as well as help on diagnostics and more complex repairs, vlogs, motovlogs and epic rides on the beautiful Sierra Nevada and Lake Tahoe.
Пікірлер
I got a DBholders subframe and mine is a 2006, the holes for the subframe are different sizes and from looking at the oem diagrams theres just a washer and a bolt that goes in there for the 2017 one. did they change bolt sizes or does the washer fill the wider hole or how does it mount? Because as it is right now i would need to get something to fill up that bigger hole unless it goes into the subframe and the sides of the bolt holds it in.
this is a GREAT video, but for anyone reading this that does their oil changes you should know that the type of oil used is temperature sensitive. Refer to your owners manual for which grade of oil to use - 15w-40 is the appropriate grade for the summer. If you're in a colder environment where it freezes during the winter you'll need a lighter oil for the winter. I travel a LOT in my RV so I carry all 3 grades of oil with me so no matter what I have the appropriate oil on hand.
Hello, a few months ago I bought the predator 3500, and I only used it a few times and I kept it for about a month and now that I turned it on it does not remain stable, I hope you answer me what you think is the problem.
Glad you’re doing well. Be safe and happy. ✌️
Nice!
How much did this cost to do ? Also where did you get the 2017-2020 fairings from ?
All of that is on a video at the end of the playlist
The plastic screw on the side of the carb is a idle screw, not a throttle stop. You tighten it all the way and then loosen it slowly until the idle doesnt change. If this screw is in too far, the idle won't come down in eco mode.
Why didn't you change the gauge cluster for the new one? Is it even possible? Im interested
Not worth the hassle. I look at the road not my cluster when I ride.
Could you please confim me the rpms of these generators runs at full throttle? And how much CC engine is in the kipor KGE7000 TC model?
Tengo un generador modelo IK 2600 h soy tecn y estuvo 1 año parado fui a entenderlo y nada procedí a limpiar el carburador y probar los swichs y la bujía no funcionaba la cambie y nada procedí a probarla y resulta que pasa la tension una vez y después no funciona la volví a cambiar y me hizo lo mismo pregunta será la tarjeta ?
tiene aceite al nivel correcto? el aceite tiene un sensor que corta la chispa a la bujia si esta bajo. la computadora nunca corta el funcionar del motor. otras cosas por probar son el boton de "Run" si no cierra el circuito puede que corte la chispa. ultimo me fijaria en la igniccion que genera la chispa con el tiempo del motor. aveces se dañan por estar paradas
En español podrías dar uno videos xfa
en que te puedo ayudar?
where can i buy the bodykit from?
Yamaha or a used original set from another rider
Спасибо! Это лучшее видео по обслуживанию этого генератора!
do you think i can bypass the CO sensor of my champ 4500 gen so it wont shot off if im using on my semi chasis frame? if yes how to by pass it?
You should make an exhaust extension instead. I'm not familiar with the Co sensor on these. And if i was it probably wouldn't be a good idea to show people how to disconnect them.
This is my go to refresher video for my Champion generator carb cleaning. 👍
Happy to hear!
Bro it has abs and another power mods a b c ? İs it possible abs on this bike?
nothing is impossible it might be possible to retrofit an ABS system but a lot of parts would be needed for that one to work. in my case the bike doesn't have ABS
Thank you sir, this helped me out tremendously. I was struggling to get mine started and changed out the ignition coil due to no spark. Then still wouldn’t start only to find those jets plugged up pretty bad. Cleaned them and she started right up. Hoping to come across how to adjust the valves on it though just to make sure it is good.
ignition coils rarely go bad. how did you diagnose and conclude that it needed a new one?
Can you give me the inverter board number to order and the cost of the board
it's literally in the video right at 2 mins
good job, liked your video if ever do video on how to install lowering kit on r6.Thanks
Thank you. you will prob never see me lower my R6 tho.
Great video n bike. God bless.
My 1100 is very picky with fuel. If it sits for a cpl months it’s a carb disassemble and clean
The manual says the intake and exhaust should be 0.002" to 0.003". In your video you say .007" why the disparity?
can use an oxy acetylene tip cleaner too for the jets
Johnathan, appreciate your video so much! I'm in Montana, and my predator 3500 has been running just crappy. After watching your video a couple times, I purchased a jet assortment with a 75 jet in it. Just put that in, the original factory install was a 77. I'd previously changed the spark plug, no change, it would still chug and oscillate rpms. The new 75 jet did the trick, and it's running like a dream! Thank you. Hope to see more videos soon.
Why would you even do that !? The newer model is not better looking than the older one😢 smh
because I can :)
@@immortalengines1605 lmao
I cringed at the fact that you didn't have any jack stands to save your butt if any of that moved... If you ever decide to do anything like that again invest in some jack stands it's a very cheap form of life insurance! You're way too young to end your life for lack of a jack stand or two!
I cringe at the fact that you failed to realize I had a whole crossmember still in the truck preventing anything falling on me.
Can you ride a passenger after the swap? I know the 2010 r1 -->2015 r1 tail conversion guys cant anymore.
Yes you can. I have been for the last 3 year with no issues.
Hello, I want to swap in a Champion module into my Yamaha 3000, do you know what the ac voltage requirement is from the Sub Coil on the KIPOR or Champion? The Yamaha is around 15 to 22 vac. The Yamaha has a 5 wire stepper motor so I will need to swap to a 4 wire. Thanks
Sorry I do not remember off of the tip of my head. But if you wire it correctly it will prob work
@@immortalengines1605 No problem; thanks.
Cleaning the carb didn’t help. Still runs only with open choke. What else should I look for?
prob clean it again. if not you can buy a replacement carb on amazon for not that much.
How can I find the 240v part number equivalent of this?
Enjoy your video's, learning a lot about my small engine generator. And yes, would definitely be interested to see a vid of what you do for your actual job. Since it takes you traveling a lot, curiousity is piqued - are you into personal security? CIA? Something more intriguing? Looking forward to your next video.
Great Video! I have a 3500, 2, maybe 3 yrs old, with very few hours on it, running rough. Your video's (the carb clean, and this with the bent push rods) really helped. I'm in NW Montana, so am also going to clean the carb, and check the jet size. If it's a #76, going to look for a #75 for this guy. Appreciate your putting these vids together.
Nice job man. Thanks for
Hello...my Honda EU 3000 generator is leaking gas...could you help me?....thank you again...regards from Argentina
Hola, yo tambien soy Argentino! enviame un email a [email protected] con fotos de donde pierde nafta y de ahi vemos... -Jonathan
New sub here. but it's difficult to watch coz camera angle
My generator wasnt running at all. I did all that you teach us here and now the generator runs perfectly in Choke position but when I turned the dial to Run position the generator turn off. I don’t know what could cause this malfunction.
Thanks for the great video! Helped me get my generator running again!
hey i know this is old video, but i wanted to ask if a digital dash from newer yamahas would work on older ones ? , i have 2010 yamaha r6 and i plan to do the conversion also, but the old dash triggers me a little bit and i couldnt find any forums and info about it anywhere else, mybe you would know.
I'm not sure it would work and I don't think it's worth it to be honest. what might also happen if it works is that it will be lit up like a Christmas tree with ABS and traction control light's since the bike I'snt equipped with those.
@@immortalengines1605 thank you for responding, might better look at at zx10r dash, found someone who did it and it looks just amazing
Relax. Live your life. Posting regularly on KZread can become a time-eater that becomes like a second job. If you're going to do it, only do it when you feel like it. Your fan-base will survive. You asked, that's my opinion.
Disassembling my Champion 3400 Duel Fuel today to see why propane was flowing through the carb when the generator was not running I noticed the Inverter panel showed signs of overheating and I wondered if that was why it stopped running on gasoline yesterday and refuses to start except for a few seconds with starter fluid. Tomorrow I'm going to try unplugging like you did and see what I learn. Watching you remove the carb gives me the confidence to pull it in my quest regarding the propane-flow problem. Can't thank you enough.
Does someone know if you can do this to a 2003 r6?
the lowest year i have seen possible is 2008 r6.
Hey man, I haven’t even started my generator up yet but with your very easy video I’m very great video I think I got my CarPlay and so I’m gonna get some brand new gas for the car and I feel like it’s gonna work so thanks so much
thank u my friend I have fixed my generator, I cleaned the carburetor and now is working like a rolex 😂
Gd day sir, I also have this same generator with a leaking petcock, any idea where to get a replacement pet cock? Thank you
Thank you. I own this Champion generator, use it once and now I believe I can bring it back to life after nonuse.
Thanks bro, now I have power for my family if the power goes out during a storm that we’re currently having. I appreciate it 🤙🏼
that makes me happy! make sure to run it out of gas and drain the carb then give it some pulls to make sure next time you fuel it up it runs 10/10
What happens if the propane part runs but the gas part doesn't work on the duel fuel generator
bad gas clean or replace carburetor
isnt this a problem when police stops you? or how do you manage legal paperwork?
No problems at all they have no clue it's been swapped. Vin number is the same
I love those colours. I was looking everywhere in Uk but no luck so it will be black but as mint as possible. I am not expecting miracles about finding many in top cosmetic since they 20 years old or more but will look any way.
I watched the vids when I don’t have an r6 lol, nice bike