Пікірлер

• 
  @CD313376 күн бұрын

  12:18 scuffcore

• 
  @Voltermort5 күн бұрын

  I can't seem to figure out what you're pinpointing?

• 
  @rcfreakamit13 күн бұрын

  Cool build and very helpful. I'm doing a Trek Marlin 7 (brand new) conversion here. Pulling the cranks out here was a hassle, too. A 50cm cheater bar finally did it. What size tires do you have on now?

• 
  @Voltermort13 күн бұрын

  @@rcfreakamit nice! I'll be curious to see when you're done. Which voltage battery? I've heard 48v has way less controller failures ling term. I have 2.25 * 27.5 tires. My previous has 26*1.75" and it was brutal to ride on anything not perfectly flat

• 
  @jessiestar415716 күн бұрын

  Why 02b & not the 02 ???

• 
  @zantesh16 күн бұрын

  The BBS02 is an amazing motor really, my 1500w rear hub with a 960wh battery gives 32 miles with heavy pedaling, Whilst offering significantly less torque only 40nm, whilst your getting 3x that with half the power.

• 
  @Voltermort16 күн бұрын

  @@zantesh oh wow. That's some good perspective because I have been really curious about hub motors lately. I actually purchased a BBSHD for 208US on an eBay auction rectently. 424CAD in total. Should check out the used eBay auctions.. I believe the account name was "mossen"

• 
  @zantesh16 күн бұрын

  @Voltermort Did you find that the bbs02b wasn't enough in the end? Since you are considering hubs. That price for a used bbshd is amazing, I'd buy one in a heartbeat for that much.

• 
  @ryanmontisnlp18 күн бұрын

  3328 mAh ---- dang

• 
  @benspokes604418 күн бұрын

  Where can I find 3d print files?

• 
  @Voltermort18 күн бұрын

  @@benspokes6044 www.thingiverse.com/thing:6632273

• 
  @ziaearthquake19 күн бұрын

  Nice! Or should I say, cellular!

• 
  @Voltermort18 күн бұрын

  @@ziaearthquake watt does that mean?!

• 
  @aski152919 күн бұрын

  Do you still recommend this kit ? Someone offered me a brand new bbso2 kit for 300€ and im really thinking about buying it

• 
  @Voltermort19 күн бұрын

  @@aski1529 I totally recommend it. I've got over 2,000km on mine and going strong. I would personally be more interested in the bbsHD these days

• 
  @lauchlanmenegon591620 күн бұрын

  do you need to pedal to make it go ?

• 
  @Voltermort20 күн бұрын

  you don't have to, there's a throttle, can take you without pedalling no problem but this BBS02B is more intended to assist you while pedalling in my opinion. The assist is very strong, even at best, i would say i'm contributing only 10% to the momentum. The bbshd can go throttle only all day without overheating i think. BBS02B heats up a bit easier i think

• 
  @XXHellBig125XX22 күн бұрын

  where are the cad files?

• 
  @Voltermort22 күн бұрын

  www.thingiverse.com/thing:6632273

• 
  @seltzerkid841923 күн бұрын

  will the battery be removable? aka, after a ride or before a ride i can take it off, charge it, and then put it back on the bike?

• 
  @Voltermort18 күн бұрын

  Yes of course. Charger connector is on the battery itself. Can be charged separately

• 
  @flavionobin-pr5rw23 күн бұрын

  amazing video thanks volt seen oher also use 2b strong so strong powerful and batteri is massive ;)

• 
  @Voltermort18 күн бұрын

  Thanks for watching :) yes, enjoying it quite a bit

• 
  @droidking61425 күн бұрын

  great fucking build bro

• 
  @Voltermort25 күн бұрын

  @@droidking614 thank you brother! 💪

• 
  @skilledcamman475225 күн бұрын

  13:00 I had a similar experience with a blue chinesium iron with a potentiometer. But I bought genuine Hakko tips to go with it and it works great.

• 
  @waynekaczmarek94626 күн бұрын

  Hey fella I don't know if you'd be interested in building a couple of battery packs for me, I'm not sure I could without burning down or blowing up my place,and just want someone to help me because of that, would you consider doing something like that??

• 
  @Voltermort26 күн бұрын

  @@waynekaczmarek946 hey wayne, I would be interested! I've actually just purchased a couple tools to improve on things I could have done better in my first battery build video. Where abouts are you located?

• 
  @waynekaczmarek94626 күн бұрын

  @@Voltermort I'm like 70 miles west of Chicago, are you very farr away?

• 
  @waynekaczmarek94626 күн бұрын

  @@Voltermort I'm wanting to build out a mountain bike with an dependable motor, I've been looking all over and don't want something cheaper because I think things are going to be pretty rough in the coming months and some of these places that sell motors and such may have a hard time getting supplies, I'm just guessing

• 
  @waynekaczmarek94626 күн бұрын

  @@Voltermort so are you really far from me?

• 
  @Voltermort26 күн бұрын

  @@waynekaczmarek946 I'm over in Toronto Ontario Canada. Might be a bit of a hassle dealing with the border. Prices on amazon are pretty competitive to what materials would cost. Admittedly I could likely build with a higher build quality

• 
  @joeberginc7415Ай бұрын

  Soldering any solder is easy with a good iron. The world is flooded with crap irons...and people that think that they are bad at soldering because of it.

• 
  @Voltermort18 күн бұрын

  That's one thing I haven't tried is a quality iron.. good solder made a giant difference. I wonder if it would be the same with a better iron

• 
  @johnstather5815Ай бұрын

  pizzatime iptv 10 days free trial Brilliant service / monster iptv 24 hours free trial Both services ARE great😀😀😀😀

• 
  @miningking70Ай бұрын

  Well done! Nice video build! Go 💚 DIY

• 
  @VoltermortАй бұрын

  Appreciate it 🙂

• 
  @42.JАй бұрын

  Will this work on a bike without gears

• 
  @VoltermortАй бұрын

  Yes for sure. But I'd recommend a hub motor personally for a single speed bike

• 
  @davidvoros2498Ай бұрын

  Hello! Approximately how many kilometers can the battery last using only the throttle. Thank you in advance for your answer!

• 
  @VoltermortАй бұрын

  I have never tested but with pedal assist contributing quite a lot of assistance, i can get about 75-80km

• 
  @ziaearthquakeАй бұрын

  Dang that new build looks sweet!

• 
  @ziaearthquakeАй бұрын

  Sweet! Hit me up with that link!

• 
  @AbdulrahmanJАй бұрын

  What disign program you used ?

• 
  @VoltermortАй бұрын

  That's fusion 360

• 
  @AbdulrahmanJАй бұрын

  @@Voltermort thanks ❤️

• 
  @LiPowerONАй бұрын

  Super build. If any one is looking for a battery for there diy build make sure to check out my bio in my channel!

• 
  @CranaАй бұрын

  I converted my GT Aggressor XC2 last year, seems similiar to yours except mine has hydraulic brakes. It was my first ever conversion and it went perfectly considering the bike is over 14 years old. I've done about 700km and not had any issues. I use brake sensors and a shift sensor too which took a lot of time to get right. 20Ah battery and range is about 65KM on level 2 assist. I have the programming cable which I need to look into, level 1 is too low and level 2 is slightly too much assistance for my needs.

• 
  @VoltermortАй бұрын

  Right on that's awesome. This was my second build and should have gone smoothly until I had to start drilling the crank arm apart lol

• 
  @ryanmontisnlpАй бұрын

  I want to do a similar build but I'm pretty sure I'd want to add a train horn to the build. Do you think the main battery would be ok to power the compressor? Or do you think It would be better to add a dedicated battery for the train horn compressor? I'm looking specifically at the "HornBlasters Conductor's Special 228H Train Horn Kit" if you're curious to see what I plan to add.

• 
  @VoltermortАй бұрын

  Adding a train horn to your build will certainly be interesting :p Have you considered having a cannister of compressed air to power it? Maybe add a digital clock and some loose blue / red wires for aesthetic to the tank :p

• 
  @plavonicaАй бұрын

  You would need to convert 48vdc to 12vdc @25amps. That's going to need a hard-wired connection, larger wiring, and an inverter that can handle that. Each time you start the air compressor you'll drain the battery by a certain amount, which will reduce range.

• 
  @huskylord123Ай бұрын

  Awesome video.

• 
  @VoltermortАй бұрын

  Thanks! Appreciate it 💪🙂

• 
  @huskylord123Ай бұрын

  Thanks for the video. As a fellow Torontonian, I'm also contemplating this DIY given the insane traffic. Do you mind sharing where you purchased your BBS02B? I'm debating purchasing via Ali Express versus trying to find a good e-bike store here in the GTA that might be a good source for parts. Cheers!

• 
  @VoltermortАй бұрын

  So you feel the pain that I feel everyday. Honestly this plus a bike rack has saved me hours every single day. I actually bought from amazon.ca . I can let you know the seller when I get home. Pretty sure it's the only one. No complaints!

• 
  @VoltermortАй бұрын

  Hey so i checked and the seller was Accolmile. on amazong. No complaints. They were helpful when i had to message them after the initial order as welll. I think you should go for it if it saves you from being stuck in traffic and gas. So far i've taken $140 off the total price in gas savings

• 
  @michasliwicki58492 ай бұрын

  Hi! Very important and usefull video, thank you! May you share 3d files for battery pack and case?

• 
  @Voltermort2 ай бұрын

  Thanks for the comment! sorry i've been procrastinating on creating a thingicerse. just made one but now have to wait 24 hours before uploading unfortunately.

• 
  @michasliwicki58492 ай бұрын

  How can we find you at Thingsverse?

• 
  @Voltermort2 ай бұрын

  @@michasliwicki5849 I created an account called "voltermort"

• 
  @dr.mikeybee2 ай бұрын

  Those brakes are way underpowered for that engine. Please be careful.

• 
  @noelbondad74232 ай бұрын

  Thank you for your videos. I dont know ANYTHING about 3D printing. Wheres the best place to start? What should I buy to START off?

• 
  @Voltermort18 күн бұрын

  Sorry for my late response. What I did before I ever got one was downloaded the software, fusion 360, and saw how I liked 3D modeling first

• 
  @davidlegard98143 ай бұрын

  Watt-hours per mile is a good indicator of economy. Another, simpler, metric is kilometers per volt used. Generally you can get a range of 8 or 9 volts from full charge to full discharge, so you can estimate cycling range without any power calculations.

• 
  @brianbassett437922 күн бұрын

  Get a Grin Satiator and start thinking in Amp Hours.

• 
  @Voltermort18 күн бұрын

  Sorry late response. I really like that idea. Much simpler

• 
  @TriLaserArt3 ай бұрын

  Hi, great vid. I see you have very similar break/gear shifters as i have. I was wondering did you add the motor cut off switch to the breaks, i cant quite see. It also says the recomended cassette is a 9 speed and i see you have 7 like mine. Does it make much of a difference? Thanks

• 
  @Voltermort3 ай бұрын

  Hey, thanks for that. I didn't add the shift sensor, instead I use the brake sensors. it is a little bit tedious as you have to remember to do it though. Something I have been meaning to get around to... I also never knew that about the 9-speed. It hasn't been an issue at all. Although I think the reason that they want you to have a 9 speed is to reduce the scenario that the motor is spinning slowly yet applying lots of current which would generate lots of heat. My guess. I just make sure to be conscious about not applying the motor at extremely low rpm and high torque scenarios

• 
  @ElectricBikeLaboratory3 ай бұрын

  Nicely done !!!

• 
  @Voltermort3 ай бұрын

  Thanks man! Your slim pack 2.0 build was awesome. I believe I sent you a message on marketplace once if i'm not mistaken. Cheers

• 
  @ElectricBikeLaboratory3 ай бұрын

  @@Voltermort Haha nice, yeah small world I see you're in the Toronto area. Very cool to see the DIYers strong in the ebike scene. We're in Hamilton. After doing a lot of 3D printing on our end I can see how much thought / effort / design went into your pack, very cool indeed. Looks really good on the bike btw

• 
  @Voltermort3 ай бұрын

  @@ElectricBikeLaboratory appreciate it it man! Yes, always cool to see local DIY'ers. Nice I'm just over in Burlington.

• 
  @Voltermort3 ай бұрын

  Oh yeah, so much work. Lots of prototypes. Honestly this project took years. I attempted it years ago but didn't have the stability/ time. Gave it a second attempt now and glad that I got it completed and can move onto something else lol.

• 
  @mashvids10183 ай бұрын

  Great work 👍

• 
  @Voltermort3 ай бұрын

  Thanks for the support!

• 
  @koparkakopie45803 ай бұрын

  What is the max speed on 26 wheels? I have got gt arrowhead and i bought bbs02 500watt and 20ah 48v. Not yet converted. Are U satisfied with results? Any problems with chain line?

• 
  @Voltermort3 ай бұрын

  It has been great. With a 48T chainring, i could hit 50kph if pedalling hard. Most of the time around 40kph. I'm very satisfied however sometimes when you have to come to an abrupt stop, and are still in a low gear, its very hard to get the bike moving from a standstill in low gear with the extra weight to shift up to a higher gear and get moving again. Takes a bit of planning. Shift up before stopping. One more thing to think about though. Makes me curious about a hub motor.

• 
  @bigmakdaddy3 ай бұрын

  Good video, very informative. If you need more 18650 cells for your next project, you can contact me. I am based in Brampton, Ontario.

• 
  @Voltermort3 ай бұрын

  Thanks, appreciate it! I'd be curious to hear what you've got

• 
  @brianbassett43793 ай бұрын

  Why do you need a bigger battery when you don't seem to ride?

• 
  @Dan-ip6je3 ай бұрын

  The dude has 3 videos on his channel...all about building and modifying his ebike. How could you possibly infer that he doesn't 'seem to ride'?

• 
  @Voltermort4 ай бұрын

  Thanks. My pleasure. Just give me a minute to post on thingiverse and I'll add to the description

• 
  @claverton4 ай бұрын

  Looks like a real goody! Would love to receive the file thnx

• 
  @shannongoulden89414 ай бұрын

  Good video, thanks for the inspiration!

• 
  @shannongoulden89414 ай бұрын

  Wow great project! I’m going to give it a try

• 
  @tylerallison86814 ай бұрын

  I always check this channel out for my self battery needs

• 
  @tylerallison86814 ай бұрын

  You're so right thanks for your information

• 
  @shannongoulden89414 ай бұрын

  Yea it's the best

• 
  @Voltermort4 ай бұрын

  Hehe thank-you 😅🙏​@@shannongoulden8941

• 
  @user-jt5vm3mi1w6 ай бұрын

  Crazy it's legal

• 
  @Voltermort3 ай бұрын

  Not legal where you're at?

• 
  @ItsFixable7 ай бұрын

  I love your custom band clamp idea for battery attachment and have made use of it. I gave you credits in my video comments of my custom ebike build video (to be released on 12/15/23).

• 
  @Voltermort7 ай бұрын

  Thanks for saying so! Glad you found it useful. Many months later and that mount has been rock solid.

• 
  @Voltermort7 ай бұрын

  I'll keep an eye out 😉

• 
  @claverton9 ай бұрын

  Your DIY bike stand looks good, I might copy that. Also how you used the ladder as a bike work stand a good idea. Good vid thanks.

• 
  @Voltermort9 ай бұрын

  Thanks, appreciate it 🙏

• 
  @mysticlll9 ай бұрын

  thank you for giving the battery specs, volts and Ah. You would not believe how many people miss that!

• 
  @Voltermort9 ай бұрын

  Thanks for watching :)

• 
  @ziaearthquake11 ай бұрын

  Voltermort 😂

• 
  @ryanmontisnlp11 ай бұрын

  Love this. Im gonna build my own just so I can make a competing YT channel and destroy you. 💜

• 
  @Voltermort10 ай бұрын

  hahaha <3

• 
  @puappo11 ай бұрын

  Phenomenal video. Great build! Looking forward to more content 😃

• 
  @Voltermort11 ай бұрын

  Thanks! 🙂