My name is Kayvan and on this channel, I am going to cover my projects which mostly are crafting, making, woodworking, fabrication, repairs, maintenance, welding, and also tools review and recommendation. Since I was a kid I always enjoyed playing with tools and tearing stuff apart, now I am trying to fix and create new things.
Disclaimer
The material covered on this video channel is for entertainment purposes only. We take no responsibility for what you do with this knowledge. We cannot be held responsible for any property or medical damages caused by items you see or learn about on this channel. We would advise you to check your local laws. Some of the items we refer to are illegal in some areas, and we would highly advise you against building these in said areas. All opinions expressed here are our own. Every link is posted on this channel may contain affiliate links, meaning we would financially benefit from your purchase if you buy through these links at no extra cost for you.
Пікірлер
That is amazing keep on making
V8 from wish💀☠️☠️
I got an instant 100% when I made this
Are we all gearheads?
It seems like it!😃
lol ❤
❤❤
better learn to sharpen a drill by hand.. way simpler and way better than this abomination..
Amazing bro ❤
How
So good it can be use in mini car
It can’t be supercharged without valves lol
lol
How is your air compressor so silent?! or are the audio levels adjusted? Thanks for the video!
I love it very much ❤
Puedes subir un tutorial de como hacerlo
I love to know how it done
Water engine
Ha,ha,ha,..😂 that handle is never gonna hold!
I mean, I didn't say it is the toughest handle in the world, but it's been a few years, and so far, it is doing alright.
Very helpful, both Part 1 and Part 2. Thanks for posting this.
GOAT! Thank you. No need to get a vacuum pump! 🖤✊🏻
grat video.....bravo
I like it,keep it up
Obviously you are listening to experienced folk. So I am looking forward to version 3 of your idea. I have kept the address of your videos as a future reference asyou develope further. Thankyou for toning down the music too as well as showing us your idea.
Can you attach a vacuum gauge to measure the pressure of the vacuum. How much vacuum are you able to develop with this vacuum pump?
Possible, but unfortunately I don't have one.
Very cool, but I got a question: If the coupling is gonna damage the compressor when it is not connected (no air went through) then will it also damage the compressor when it pull out all the air inside the plastic bottle as well?
TBH, I had never checked it, neither for the connector nor with the bottle, to see what is going to happen, and this is just my prediction. You are correct at some point when the air inside the bottle is all sucked it is exactly the same situation and I don't think it is healthy for the compressor to keep it running like this.
Pls
Great video dude. So simple lol just connect to the intake port. Dunno why I didn’t think of this. Do you run any risk of damaging anything here?
Thank you, my man. So obviously, this device is not designed for such an application, and I can not recommend anyone to use this method because I did not test it long-term. So please "do at your own risk" this video is just for satisfying my curiosity.
Wow
Lol that bottle is not going to work a 5 gallon bucket wont work i imploded 1 u need glass to use as vacuum!!
So, technically, it works, but you will need a huge container or a lot of small containers. To give you some idea, to fill a normal 15" tire with 30 PSI, I think I have to empty the tank 6 or 7 times! My thought, if you want to do a quick and cheap paint job, just use a spray can.
So the pressure stays at zero?
I'm not sure what you meant, but I managed to reach up to 30 PSI, as you can see in the video.
@@KayvanCrafted I was referring to the pressure on the large water container
@@Breal191 OK, so in the short video there no pressure left in the tank because I used it all to fill in the tire. Please check the link for the full version it starts .It starts at the point it shows the 30 PSI in the tank. kzread.info/dash/bejne/aWmBmdmxo8XSgtI.htmlsi=lrhiZ_bexrDYSzh0&t=184
@@KayvanCrafted Right on! I want to use it to paint instead of using pipe and zig zagging them up and down my garage wall to get dry paint. I figure if i string a few of these containers plus a water filter I might get decent results when i paint my car bumper. Looking for a quick and dirty set up.
@@Breal191 So, while technically it's possible I don't recommend it. Just to give you some idea to fill in a normal 15" tire with 30 PSI I had to empty my 20 litre water tank 5 or 6 times! My recommendation, if you want to do a cheap paint job just use a a few spray can.
HOW!!????? PLEASE TUTORIAL!!
The next one would be with maps and stuff, but this does not have, sorry.
Is that dom's dodger v8?
Haha 😂 good one. Missed The Fast and the Furious...
which size of Angel Grinder you have?
it's a 115mm equal to 4.5" inch.
@@KayvanCrafted can we Place it For 5 inches angle Grinder or we Can't ?
@@houseconstructionwork2817 Technically, you can do this with any size of angle grinder with a suitable chuck. Just make sure to measure your angle grinder shaft's thread with a thread gauge and use the same size tap on the chuck. You can watch the full video here: kzread.info/dash/bejne/g4psu8qaks7SY5c.html&ab_channel=KayvanCrafted
Agg to nikal
Are you a vampire?
😂 OMG why?
Bro that's amazing ❤❤❤
What liquid did you put in before the piercing?
So my go to is engine oil, you can even use the used engine oil it's ok. A lot of people may not agree with me on this though. I don't like thin liquid like WD40.
@@KayvanCrafted thank you
Gracias por tu suoer tutorial... muchas gracias!!!
Bro please do it with turbo
🤣 You're a turbo guy...Ok, I will try that. TBH, the whole thing was supposed to look like an American V8 from a muscle car, and turbo is not really a thing they are known for.
Yes i love turbo if you can make with this engine a turbocompressed engine:)
😊
Why do people insist on having music in a video that distracts from hearing what is being said?
You are completely correct, my early videos; on a side note you can activate the subtitle if it helps.
Can this hurt the compressor at all? And how close to a perfect vacuum can you get compared to a dedicated vacuum pump?
It is possible to destroy your air compressor, so do it at your own risk. I never had a vacuum pump, so I cannot compare, but obviously, a vacuum pump would be far superior to a converted compressor.
How much Lpm or cfm it can provide
Depends on the compressor, my friend.
Goodnight! Beautiful work, congratulations for sharing your project. Would it be possible for you to measure the materials you used?
Thank you. I'm so happy to see you liked this project. Unfortunately, I don't have any measurements and maps for this project available, but I will keep that in mind for my next projects.
Same problem hii
Bhai ye kaha se kharede
How much time I took you to make this
Well, it depends, if you have everything available and you know what you are doing, maybe even 4 hours. It could be more than a day. I did it in two days. Crankshaft is the tricky part!
Is there a template?
Unfortunately, there is not.
Do you sell the 3d files? I am interested
I appreciate your interest but unfortunately don't have any CAD file for this project.
Solid 9 out of 10! Great job well done.
Thanks mate.