From your lawnmower to your coffeemaker, we provide quality repair parts and how-to videos to make your repair quick and easy. We aim to empower you to do simple DIY repairs yourself in order to save time and money. With Fix.com, you're handier than you think!
Пікірлер
anyone figure out how to get the seal off the motor?
Thank You! Needed to really pull on it but I got it out. Thank you Amazon and Mr. Fix! Cheapest repair ever!
How do you know what new carburator to get?
Thank You very much for the great informative video my dryer is working again! YAHOO!
That's a stupid idea wiggling it back and forth that's how I broke me outlet line
Nice video...I've owned the exact same washer since 95'...
How do you take off the whole thing?
Thank you ❤
I installed a new part but as soon as i press the water dispenser button the water pump burns out. Happened twice so is not faulty piece. Ia the correct model
ARE YOU SERIOUS!!!! We don’t need a video on how to open it. I want a video that shows how to REPLACE THE MOTOR. 😩 UGH
This video makes it look very doable but I'd suggest looking at others as well. The bearing caps will usually be seized into position. These parts will need to be forced/broken off. I had my Maytag serviced many years ago. Not many will work these because of the difficulty. 😮
I am so grateful for this video! Thank you so much for the great tutorial. I did it several years ago and now I think I was remembering I was never gonna do it again. Ha ha! But you made it easy enough to follow. Thank you!
Your video made my replacement of the hot and cold water inlet valves easy and very quick. I especially appreciated your mention of the Phillips screwdriver and the slip-joint pliers. That was all I needed.🙂🙂 Normally, I would have brought half a toolbox. That isn't needed. All you instructions were perfect. Thank you. You helped me a lot.
I’m dissatisfied with mine. I’ve had it for 7 months. The front panel is cheap, one of the two brackets that secure it to countertop in front broke, the upper sprayer fell off and nothing in the Manuel to help me figure out how it was attached, no instruction on how to take the middle drawer off, got it off and now it isn’t level as it dips in the front and a plastic piece fell into the bottom and no idea where it came from. Very cheaply made.
What is the part number for the replacement drive belt?
Thank you so much, I have the exact same model and I thought I'd never be able to put the door back on !
Thank you for your tips...very useful since they were not indicated in the installation manual, even in official videos of the brand right here on YT. Ironically, manufacturers are increasingly making the installation of electronic devices more difficult and delicate, instead of the other way around. The only thing that was missing from your video is what was already indicated in other comments, and that is what would be the least complicated way to raise the washing machine to the pedestal. Keep up with the good content!
By the way, you don't necessarily need the Whirlpool replacement part. The only thing you need is 1/4 inch polyethylene tube that you can get from the pluming section of any hardware store.
There is another video without taking everything apart to put the belt on!
Very helpful! Thank you so much. 🙏🏼
Sweet thistle PIE!🤟
my controller and electrical elements are no where near the pus in pull out controller
Looks like tying it up didn't work so well!
For the rust inside the wheel barrow you can plug up the holes and purchase several containers of Evapo Rust from harbor freight, pour it in, and let it sit overnight. It will dissolve all the rust. That’s what I did. Worked great and ensured I removed all the rust inside the wheel barrow bucket. A grinder may not get all the deep seated rust inside the bottom of it.
Trash your fridge dont go down this rabbit hole. Appliance repair tech with 10+ years repaorting in
I was so proud of myself for replacing that crazy boot! But I had to save the spring wire for my husband!
Watch for bleach dispenser rubber pipe pull it out before lifting top
Why on earth did he takeoff the casing from the whole washing machine?
Good instructions. Very poor video. I couldn't see a thing you were doing. No reverse angle shots. No close-up views of your hands or the parts you talking about. Way too many steps. Why not remove the pump from underneath the machine, after you remove those screws in the front? s m h
Can’t put stove burner tops flat
How to put burner tops back on correctly? Won’t lay flat
Show how to put burner top back together
I see you dont reply but thank you
Loved that you got straight to the point! How to videos can be 10 minutes of dialogue before getting to the reason for watching ever starts!
How do you know that the timer is not working
Thank you!!!!! This was perfect!
helped a bunch, thank you
Thank you!
Thanks. Excellent and clear instruction video. There is no need to torque the cylinder screws down? Subscribed.
Aviation fuel...best fuel. Bought an airplane, been sitting in a hanger for 20 years. Had about 10 gals. in each tank. Added a fresh 5 gals. to both sides. No problems!😊
I love the internet. Saved me at leaat 20 min arguing with my father in law
Excellent video, thank you!
If that filter cover door falls off wld you smell a burnt smoke smell?
all of a sudden the lint trap doesn't fit snugly and falls out when the dryer is running
Hey man thanks for the pulley expalanation. Worked like a charm
Great video! I just bought one for my Dad. I sent him this vid :) Very good info for first timers, well presented. 😎
All of these videos on dryer noise repair are the same - they do NOT address EXACTLY what the rear bearing should look like. How do you know the bearing is bad if it hardly shows any wear? How much wear is too much? I bought a rear bearing kit that was supposed to be OEM and the dryer now is noisier than it was before. The "OEM" bearing in the kit is not as long as the original one, allowing the drum to scrape on the little metal brackets that hold the heating elements. I'm going to install a spacer washer under the bearing to push it further to the rear, hopefully pushing the drum more to the front of the dryer where it won't scrape on the heating elements support brackets. Other than not examining the old bearing and commenting on what was wrong with it the video is very helpful as far as taking the dryer apart.
Does it matter if the handle of the unit is in the latched or unlatched position when you’re installing it?
well deosn't matter if its a dishwasher that stands on your bench since it's already connected to the sink the bubbles that seep out will just go down the drain on its own,
Your thumbnail is ridiculous. Blocking your channel. Look at the stupidity of that facial expression. What, are you 12????
They design refrigerators like this to make it difficult for the homeowner to fix their own. What a world we are living in.
Thank you for posting. What is a that pill and stick coating and the second layer? Do you have links?