One of the best information in KZread. Bro one doubt, Shogun reed valve petals too have different thickness?
@vijayam12 күн бұрын
Bro, is this tachometer reliable? How's it holding up till now?
@rxtuningpoint2270Күн бұрын
@@vijayam1 still work well.
@utkarshsinghpariharharsh319414 күн бұрын
Bro mujhe RX 100 ki Crank assembly chahiye aap arrange kara sakte ho kya?
@thenikhilkukreja21 күн бұрын
How is this grinder quality, performance and maintenance?
@raghujaggu2 ай бұрын
Sir how much Is the clearance ??comment pls
@vijayam12 ай бұрын
Bro is there any specific friction plate plate that must go first?
@allaboutnothing993 ай бұрын
Brother, please make a video on how to do it without the rpm meter. It would be helpful for 1000's of rx owners😊
@rxtuningpoint22703 ай бұрын
Rpm meter less cost approx 1500, using rpm meter only I can do the right tuning. Without RPM meter, same tuning based on engine sound.
@allaboutnothing993 ай бұрын
@@rxtuningpoint2270 Thank you. Could you please tell me the size of the bolt that goes under the silencer near brake pedal? My mechanuc forgot to put it back.
@VISHNUGAMER2 ай бұрын
@@allaboutnothing9913mm
@Kirankiran-bq7fn4 ай бұрын
How many turns air screw should be adjusted sir, bcoz I don’t have rpm meter.
@rxtuningpoint22704 ай бұрын
Near 1.5 turn, but it will vary each bike. 1.25 to 1.75 range, not more.
@Kirankiran-bq7fn3 ай бұрын
Thank you for the reply
@ab99eeАй бұрын
@@rxtuningpoint2270Yes...It varies. In this case I guess bike settled at 1 full round of air screw right?
@nandeibammarconison85734 ай бұрын
Please do tunning for rx100 also
@vijayendrahirwe5024 ай бұрын
Nice information sir. But is there a sound like gajan pin bearing sound or piston lapping sound??
@rxtuningpoint22704 ай бұрын
It piston noise, installed light used std i-series cylinder. That making some noice, sound will be reduced after 3 to 5k. Now bike running better.
@rxtuningpoint22704 ай бұрын
That is bit difficult, please refer the workshop manual
@sunilbks134 ай бұрын
Can you share the torque value for all parts in RX
@mjshaheed2 ай бұрын
Please refer to the manual, Bro. There is a list of torques specifications given there.
@sunilbks132 ай бұрын
@@mjshaheed which manual bro? I don't have manual For RX series bikes
@mjshaheed2 ай бұрын
Bro, looks like youtube is deleting my comments. Please refer to the comment in your own shorts video.
@mjshaheed5 ай бұрын
How much is the torque wrench, Bro? Is one wrench needed for rx or two torque wrenches?
@rxtuningpoint22705 ай бұрын
Two torque wrench required for rx. this one model 25lbt to 150 lbt is more enough for rx. Price approx 9k in amazon.
@mjshaheed5 ай бұрын
@@rxtuningpoint2270 Thank you, Bro.
@antonysadasivam3552 ай бұрын
Your primary gear has been fitted ulta.
@mjshaheed2 ай бұрын
@@antonysadasivam355How do you say, Bro?
@rajutarkhala66025 ай бұрын
Ye matter kha se milega,??
@PradeepRaj-wb9sq5 ай бұрын
How much mileage??
@rxtuningpoint22705 ай бұрын
Millage 35+, previously with g series cyliner. Now installed I series, need to test millage.
@josco755 ай бұрын
workshop location evideya?
@rxtuningpoint22705 ай бұрын
No workshop, own work for my rx in home. Nagercoil.
@kadurahmanpuzhakara70325 ай бұрын
Bro while use aroma connecting rod it shows more length
@KamleshpargiPargi-xc5tm5 ай бұрын
Suzuki Max 100 average Nahin de rahi aur 4 Gear Mein Dab rahi hai kya problem ho sakti hai
@chesty_meme5 ай бұрын
Tuning karao acche se
@user-mt2yt8ow4i6 ай бұрын
Bro contact numerous please
@brotherrider17187 ай бұрын
Good job bro nyc helpful 👏 video 📸
@naveenkumars85777 ай бұрын
Where are you from? Are you from Bangalore??
@rxtuningpoint22707 ай бұрын
Kanyakumari
@2wheelsoulbiker5268 ай бұрын
Bhai aap mere liye ek same tool mangawa sakate ho kya? Request hai bhai, agar ho sake to pls help me out.
@2wheelsoulbiker5268 ай бұрын
Pls share your mobile no if you are ok with it
@rxtuningpoint22708 ай бұрын
Brother, I am from Kanyakumari, it's far away from banglore. My brother help me to bought this tool. This tool not available in my place. Will check my place if I can.
@rxtuningpoint22708 ай бұрын
It's crank installation tool.
@2wheelsoulbiker5268 ай бұрын
Oh machan 💔 Thanks for repeatedly replying. You are a very nice person(nalla paiyan😍) I am in love with that tool and I didn't find anywhere sry for repeatedly disturbing you machan. If you got to get your hands on similar tool then pls info me. Thanks once again
@2wheelsoulbiker5266 ай бұрын
Thanks bro I have purchased one from GMT Chennai 1190 rupees. It's the same tool you mentioned but price is very high
@2wheelsoulbiker5268 ай бұрын
Pls orovide the nomenclature and part no of the tool, i searched alot but didnt find here in india. Pls share more info about this tool. Thank you bro
@rxtuningpoint22708 ай бұрын
I bought from banglore gb road. Crank separator tool.
@2wheelsoulbiker5268 ай бұрын
@@rxtuningpoint2270 thank you bro for prompt response. May I get any contact details of the shop? I need that tool badly bro.🙏
Did you rebuild the crank? Rebore done for cylinder?
@rxtuningpoint227010 ай бұрын
Not sale bro, my own bike
@TNRxSalesGarage..10 ай бұрын
It's sale...?
@all_over_biketechnician11 ай бұрын
Please contact number
@rxtuningpoint227011 ай бұрын
Looks some sound from piston, run the bike for next 1000km, it will reduce. One carbon build up, sound will reduce.
@allaboutnothing9911 ай бұрын
Hello Brother, Recently opened the engine and changed all bearings(as per mechanic recommendation) because there was some noise coming from the bike. Now, I feel there is different sound coming from the engine like crank or piston noise. Can you pls check the below video and let me know what the issue is? Mechanic says the sound will go after 1000kms, but I am not satisfied. kzread.infoxm91shZIFZY?feature=share
@joelraj954011 ай бұрын
Duplicate
@rxtuningpoint227011 ай бұрын
What is duplicate?
@joelraj954011 ай бұрын
Duplicate plate
@rxtuningpoint227011 ай бұрын
Yes, it's duplicate plate. Orginal not good.
@Ponnanakkal11 ай бұрын
Orignal rate....???
@rxtuningpoint22709 ай бұрын
Orginal cost 800 around
@rxtuningpoint22709 ай бұрын
@@Ponnanakkalorginal came with different part number
@Tararani247 ай бұрын
original me kya folt hai
@joelraj954011 ай бұрын
Lorry engine
@rxtuningpoint227011 ай бұрын
This video is for carb tuning, not showing lorry engine.
@arthasmenethil4 Жыл бұрын
Sir, how many turns for yamaha rs100?
@rxtuningpoint2270 Жыл бұрын
I am not sure about rs100, are you mean rx100? For rx100 company recommended 1.25 + or - .5 turn. The turn will vary each rx100, you have to find the right high rpm while tuning.
@arthasmenethil48 ай бұрын
@@rxtuningpoint2270do i need to retune my carburetor if i replace my stock exhaust into a chamber exhaust?
@rxtuningpoint22708 ай бұрын
@@arthasmenethil4 yes you have to do, the petrol flow will change. That is my understanding.
@all_over_biketechnician Жыл бұрын
bro clutch plate local😢😮😢original podunga bro
@Ponnanakkal11 ай бұрын
Original rate
@rxtuningpoint227011 ай бұрын
New Clutch plates are for 4 stroke yamaha only, not good for rx135. Till 2020, plates are not good for rx. The steel plate too worst. Old stock plate run last 100000km.
@allaboutnothing99 Жыл бұрын
Bro, some people do nikel plating or shiny chome plating. Which is best and cost effective?
@rxtuningpoint2270 Жыл бұрын
Chrome and nickel platting, both same process. Shine finish as like mudgaurd. I have done zinc platting, as per the original look.
@allaboutnothing99 Жыл бұрын
@@rxtuningpoint2270 Thank you. Nickel and Chrome plating same?
@allaboutnothing99 Жыл бұрын
@@rxtuningpoint2270 One last question. I have bought aftermarket nuts and bolts kit. Most of the parts are zinc coated. Should I zinc coat again to avoid rusting quickly? Please answer
@rxtuningpoint2270 Жыл бұрын
@@allaboutnothing99 Not required, use directly. I did zinc for used nut bolt also.
@allaboutnothing99 Жыл бұрын
@@rxtuningpoint2270 Thank you so much, Brother. Please upload more useful videos.
@Shriram_767 Жыл бұрын
Hi my mikuni carb jets got blocked where to buy a new one or how do I clean my existing mikuni jets?
@rxtuningpoint2270 Жыл бұрын
Use tank resuce cleaner, you can buy from Amazon. New not available.
@jyotishmansarma4179 Жыл бұрын
Avi apke dwe4119 angle grinder kese he?
@mjshaheed Жыл бұрын
Brother, I see many mechanics hit the crank weight plates with a hammer to install it. It will ruin the crank and make it imbalanced, right?
@rxtuningpoint2270 Жыл бұрын
Some mech use round pipe and hammer to install, that won't affect much. Direct hammer will affect crank and bearing too. But both are not recommended. Company recommended the crank installation tool. That we give better smooth in crank bearing.
@mkundaikar Жыл бұрын
From where you got that meter? I need one can you help?
Nice video. I need to run my android app and measure your idle RPM. Good job. RDD CDI is unbeatable when it comes to smooth idle.
@mjshaheed Жыл бұрын
Bro, Can we restore a bike with 35k budget?
@rxtuningpoint2270 Жыл бұрын
It depend on how many spare you are replacing. Without engine work, its possible.
@mjshaheed Жыл бұрын
@@rxtuningpoint2270 Ok, Brother. Thank you
@mjshaheed Жыл бұрын
Yevlo Bro, aagum plating panna?
@rxtuningpoint2270 Жыл бұрын
Approx 2000 for 1 bike.
@KK-cd7nu Жыл бұрын
bro, your workshop location n contact number?
@KK-cd7nu Жыл бұрын
In your 5 speed, can you fit the silencer's mounting bolt below the clutch case to the bikes frame? It's not aligning properly with 6 hole silencer. Think the mounting / anchoring bolt location in rx135 5 speed is different. But it's aligning if we use cat silencer.
@rxtuningpoint2270 Жыл бұрын
Both fitments are different
@rxtuningpoint2270 Жыл бұрын
It's 4 speed model, cannot fit the cat silencer properly.
@KK-cd7nu Жыл бұрын
@@rxtuningpoint2270 ok...I tried installing rx100 6 hole silencer in my 5 speed and the center mounting was an issue..
@rxtuningpoint2270 Жыл бұрын
@@KK-cd7nu both mounting is different brother. Rx100 and rx135 chrome model mounts are same. Cat silencer model are same.
@KK-cd7nu Жыл бұрын
@@rxtuningpoint2270 ok bro.. thanks for replying..👍
@dineshshetty21 Жыл бұрын
Wher will we get this in mumbai
@rxtuningpoint2270 Жыл бұрын
You can get this Nut and Bolt shop, as well hardware tools for automobiles shop have it.
Пікірлер
One of the best information in KZread. Bro one doubt, Shogun reed valve petals too have different thickness?
Bro, is this tachometer reliable? How's it holding up till now?
@@vijayam1 still work well.
Bro mujhe RX 100 ki Crank assembly chahiye aap arrange kara sakte ho kya?
How is this grinder quality, performance and maintenance?
Sir how much Is the clearance ??comment pls
Bro is there any specific friction plate plate that must go first?
Brother, please make a video on how to do it without the rpm meter. It would be helpful for 1000's of rx owners😊
Rpm meter less cost approx 1500, using rpm meter only I can do the right tuning. Without RPM meter, same tuning based on engine sound.
@@rxtuningpoint2270 Thank you. Could you please tell me the size of the bolt that goes under the silencer near brake pedal? My mechanuc forgot to put it back.
@@allaboutnothing9913mm
How many turns air screw should be adjusted sir, bcoz I don’t have rpm meter.
Near 1.5 turn, but it will vary each bike. 1.25 to 1.75 range, not more.
Thank you for the reply
@@rxtuningpoint2270Yes...It varies. In this case I guess bike settled at 1 full round of air screw right?
Please do tunning for rx100 also
Nice information sir. But is there a sound like gajan pin bearing sound or piston lapping sound??
It piston noise, installed light used std i-series cylinder. That making some noice, sound will be reduced after 3 to 5k. Now bike running better.
That is bit difficult, please refer the workshop manual
Can you share the torque value for all parts in RX
Please refer to the manual, Bro. There is a list of torques specifications given there.
@@mjshaheed which manual bro? I don't have manual For RX series bikes
Bro, looks like youtube is deleting my comments. Please refer to the comment in your own shorts video.
How much is the torque wrench, Bro? Is one wrench needed for rx or two torque wrenches?
Two torque wrench required for rx. this one model 25lbt to 150 lbt is more enough for rx. Price approx 9k in amazon.
@@rxtuningpoint2270 Thank you, Bro.
Your primary gear has been fitted ulta.
@@antonysadasivam355How do you say, Bro?
Ye matter kha se milega,??
How much mileage??
Millage 35+, previously with g series cyliner. Now installed I series, need to test millage.
workshop location evideya?
No workshop, own work for my rx in home. Nagercoil.
Bro while use aroma connecting rod it shows more length
Suzuki Max 100 average Nahin de rahi aur 4 Gear Mein Dab rahi hai kya problem ho sakti hai
Tuning karao acche se
Bro contact numerous please
Good job bro nyc helpful 👏 video 📸
Where are you from? Are you from Bangalore??
Kanyakumari
Bhai aap mere liye ek same tool mangawa sakate ho kya? Request hai bhai, agar ho sake to pls help me out.
Pls share your mobile no if you are ok with it
Brother, I am from Kanyakumari, it's far away from banglore. My brother help me to bought this tool. This tool not available in my place. Will check my place if I can.
It's crank installation tool.
Oh machan 💔 Thanks for repeatedly replying. You are a very nice person(nalla paiyan😍) I am in love with that tool and I didn't find anywhere sry for repeatedly disturbing you machan. If you got to get your hands on similar tool then pls info me. Thanks once again
Thanks bro I have purchased one from GMT Chennai 1190 rupees. It's the same tool you mentioned but price is very high
Pls orovide the nomenclature and part no of the tool, i searched alot but didnt find here in india. Pls share more info about this tool. Thank you bro
I bought from banglore gb road. Crank separator tool.
@@rxtuningpoint2270 thank you bro for prompt response. May I get any contact details of the shop? I need that tool badly bro.🙏
Hallo bro how can i contact you?
[email protected]
Share your number, will call you.
Hallo bro how can i contact you?
All the best ❤❤❤
Thanks brother.
Did you rebuild the crank? Rebore done for cylinder?
Not sale bro, my own bike
It's sale...?
Please contact number
Looks some sound from piston, run the bike for next 1000km, it will reduce. One carbon build up, sound will reduce.
Hello Brother, Recently opened the engine and changed all bearings(as per mechanic recommendation) because there was some noise coming from the bike. Now, I feel there is different sound coming from the engine like crank or piston noise. Can you pls check the below video and let me know what the issue is? Mechanic says the sound will go after 1000kms, but I am not satisfied. kzread.infoxm91shZIFZY?feature=share
Duplicate
What is duplicate?
Duplicate plate
Yes, it's duplicate plate. Orginal not good.
Orignal rate....???
Orginal cost 800 around
@@Ponnanakkalorginal came with different part number
original me kya folt hai
Lorry engine
This video is for carb tuning, not showing lorry engine.
Sir, how many turns for yamaha rs100?
I am not sure about rs100, are you mean rx100? For rx100 company recommended 1.25 + or - .5 turn. The turn will vary each rx100, you have to find the right high rpm while tuning.
@@rxtuningpoint2270do i need to retune my carburetor if i replace my stock exhaust into a chamber exhaust?
@@arthasmenethil4 yes you have to do, the petrol flow will change. That is my understanding.
bro clutch plate local😢😮😢original podunga bro
Original rate
New Clutch plates are for 4 stroke yamaha only, not good for rx135. Till 2020, plates are not good for rx. The steel plate too worst. Old stock plate run last 100000km.
Bro, some people do nikel plating or shiny chome plating. Which is best and cost effective?
Chrome and nickel platting, both same process. Shine finish as like mudgaurd. I have done zinc platting, as per the original look.
@@rxtuningpoint2270 Thank you. Nickel and Chrome plating same?
@@rxtuningpoint2270 One last question. I have bought aftermarket nuts and bolts kit. Most of the parts are zinc coated. Should I zinc coat again to avoid rusting quickly? Please answer
@@allaboutnothing99 Not required, use directly. I did zinc for used nut bolt also.
@@rxtuningpoint2270 Thank you so much, Brother. Please upload more useful videos.
Hi my mikuni carb jets got blocked where to buy a new one or how do I clean my existing mikuni jets?
Use tank resuce cleaner, you can buy from Amazon. New not available.
Avi apke dwe4119 angle grinder kese he?
Brother, I see many mechanics hit the crank weight plates with a hammer to install it. It will ruin the crank and make it imbalanced, right?
Some mech use round pipe and hammer to install, that won't affect much. Direct hammer will affect crank and bearing too. But both are not recommended. Company recommended the crank installation tool. That we give better smooth in crank bearing.
From where you got that meter? I need one can you help?
www.amazon.in/gp/aw/d/B01N6ZT1W6/ref=yo_ii_img?ie=UTF8&psc=1
Bhai number send kro
Original saund 👍♥️
Nice video. I need to run my android app and measure your idle RPM. Good job. RDD CDI is unbeatable when it comes to smooth idle.
Bro, Can we restore a bike with 35k budget?
It depend on how many spare you are replacing. Without engine work, its possible.
@@rxtuningpoint2270 Ok, Brother. Thank you
Yevlo Bro, aagum plating panna?
Approx 2000 for 1 bike.
bro, your workshop location n contact number?
In your 5 speed, can you fit the silencer's mounting bolt below the clutch case to the bikes frame? It's not aligning properly with 6 hole silencer. Think the mounting / anchoring bolt location in rx135 5 speed is different. But it's aligning if we use cat silencer.
Both fitments are different
It's 4 speed model, cannot fit the cat silencer properly.
@@rxtuningpoint2270 ok...I tried installing rx100 6 hole silencer in my 5 speed and the center mounting was an issue..
@@KK-cd7nu both mounting is different brother. Rx100 and rx135 chrome model mounts are same. Cat silencer model are same.
@@rxtuningpoint2270 ok bro.. thanks for replying..👍
Wher will we get this in mumbai
You can get this Nut and Bolt shop, as well hardware tools for automobiles shop have it.