“Mistry MakeTool” Is A KZread Channel For Homemade Tools Project, Woodworking Projects, Tools Hack, Workshop Tricks And Tips And Power Tools And Hand Tools Review Run By Sandip Kumar And Vijay Kumar.
Subscribe My Channel For All you need to know about the Proper Use and Guidelines of Power Tools/ Hand Tools / Machinery Tools.
Mistry MakeTool TO HELP YOU WORK BETTER...
For Business Inquiries Contact Us On :- [email protected]
THANK YOU...
Пікірлер
Вот это да, ну прямо золотые руки и главное всё понятно можно повторить и сделать себе такой же и какой же молодчина !
Good Job idol
Super 👍
What is the total cost?
Size of the PVC pipe?
Sir ji aap hi apna bala cooler bech do mere ko
Конструкция понравилась, лайк. Только резать нужно в противоположную сторону. Делая рез "на зуб", диск стачивается в разы быстрее.
Bom mesmo viu, vou fazer um😂
STUPID....
Quá tuyệt vời❤
Conceptually it is good, in the real world it would be damm near impossible to get a good fit on the track unless both rollers on one side had some form of adjustment and pay attn. to the parts that are just magically done like the bolt holes under the grinder.
congratulations 🎉
Wow, one of the few videos where no welding is involved AND its super simple?! Brilliant!!
Very Smart :o) I am planning to build one this weekend. Thank You!
Time to learn hindi i suppose...
Кто нибудь отберите у этого и….. ота клеевой пистолет…..
Magnets looses their capability if you hit them. so the first one will not last long.
Just curious .wat stops it from coming up of the railing tube? any chance
Super
Not bad
Please don't stoop/lower yourself to 5minutecraft's level
Muito bom 👏👏👏🇧🇷
Our agar wood ko center se cut karna raha to kese honga sir
U mums has been torn an her puss got a show stuck init an there's SPK coming out ger smelly mouth
Bravo...😊😊😊
Very nice 👌👍
What. Is the cable that u are using for your drill when it on?
Все конечно замечательно, только диск в метал должен заходить сверху, короче ехать надо не слева направо как в видео а наоборот. Не благодарите.
Can I use the heating element wire from a 220V electric heater with 12V?
ماشاء الله تبارك الله ❤
Well that was a long winded waste of time, a little over the top.
I found 2 mdf boards in the disposal, 24.5 cm x 24.5 cm, 20 mm thick and made one with the two identical boards! On the base plate I placed 2 rectangular feet measuring 14 cm long and 15 mm high made of solid wood, and on one side of these feet I screwed 2 pine bases, drilled the holes and placed a solid wood slat as a lever! I joined the 2 plates together and placed a thin plastic layer between the 2 plates to mark the hinges! When I tested with 40-gram balls of dough, even though I pressed the lever a lot, the dough was barely crushed and expanded, it didn't exceed 8-9 cm in diameter! Looking in detail at the open press, I noticed that the upper (movable) plate is an absurd 4 mm below the level of the lower (fixed) plate. Could this be the reason for the problem? Friend, analyzing the situation again I saw that the tortillas that had a small diameter of 8-9cm were thick, exactly with this difference reported above 4 mm! Could this be the cause of the problem?
कितने में बनाकर दे सकते भैय्या! काॅल करना इच्छा हो तो!
Super very nice 👍
Which size use side leg square tube
Super, very nice how money kgs support this pressing
Sir please send me material length size and details please 🙏🙏
Nice project, but in my opinion you should run a few passes over the surface rather than what you did. The cutting disc will last longer!
Wah... nampak kemas dan x makan ruang selepas dilipat kembali kedinding
Another person who made this much more difficult than it needs to be.
I don't see anything good coming out of this device. The instrument cannot be secured in this way. A situation may arise when the disk suddenly stops, the tool breaks out and an accident occurs. This is my personal opinion. Sorry.
This DIY Sliding Angle Grinder Cutting Jig is an absolute game-changer! Your clear instructions and detailed explanations made it so easy to follow along. Thank you for sharing such an innovative and practical solution!
Kya ap ye mobile stand sale bhi karty hen
Great stuff
if there is a vertical drilling machine in the workshop, then most likely, there is any other special tool there and there is no need to "reinvent the wheel" 😅
what is the name of the bearing ?
Genial amigo puedes compartir las medidas de cada pieza? Tks
Teşekkür ediyorum 🙏🙏🙏🙏🙏🙏
Man, you're my savior!! thank you so much for all those tips and tricks!!! 10/10!!!
Excelentes tus proyectos de gran calidad, pura ingeniería, Felicitaciones, Éxitos!!!