that's actually a great idea.... now I need to tripod mount it so I can shoot handgun
@kelshotss29 күн бұрын
No words spoken and easily the best instructed video I’ve seen on this
@nateez3898Ай бұрын
Best video I’ve seen on this 👍🏻👍🏻👍🏻 very helpful!
@TargetTimeАй бұрын
Glad it was helpful!
@leadpilled5567Ай бұрын
The lee bullet feeder dies work great. Not sure with an auto bullet feeder but with the tubes similar to the mini mr bullet feeder set up. I just ordered the silver layer bullet and brass feeder. We’ll see how well they work but the pics and videos I could find the fit and finish look really good. $400 for the set with disks for 9 40 45 223 included. Veteran owned company that’s making them which is always a plus in my book
@codyjenn87852 ай бұрын
I built my panther arms AR-9 from a build kit SDI sent me and I have a big wrench for tighting the barrel nut but I don't have a vise so I got it as tight as I could without breaking the aluminium receiver.
@deeeeeeps2 ай бұрын
No way is everything getting clean without pins. If I want shiny brass I decap use pins then switch to 3/16 stainless balls.
@TargetTime2 ай бұрын
7:26 looks pretty shiny
@deeeeeeps2 ай бұрын
@@TargetTime inside the pockets
@Lidt._noah2 ай бұрын
ALERT 🚨 do not I repeat do not! add a whole quart of oil when doing your own oil change on your trail master .. I just did mines earlier I have 150cc engine and i over flowed it & went up the road and it was running real sluggish so I drained it back out again and put just a little over half the bottle got back on the road & it ran a whole lot faster and better
@Lidt._noah2 ай бұрын
Do me Maintenance vids on trail master plz!!👍
@angelscomputers3 ай бұрын
Yeah, I can’t find the single stage kits he used to make, they were the best. Looks like he went out of business. Sucks, I will regret my entire life that I sold mine
@ericwerick2393 ай бұрын
Very useful thank you man I did touch it and you solved my problem of dead trigger
@LowProOperator3 ай бұрын
Just got my first colt mag block because I’m doing another AR nine build. For the past two years I have been using a Palmetto State Armory AR nine set up with the Glock mag dedicated lower and I honestly have not had a single malfunction thousands of rounds later surprisingly. I don’t have the bolt hold open, but it works fine. Now with my second GEN Pro mag block I’m using Colt mags and so far so good no jams or anything like that but I noticed with a full mag using my PSA upper I cannot see the mag. It is nearly impossible to the point where I am indenting the casings. Is that normal or is it just maybe my BCG isn’t really set up for Colma? It seems to function and shoot OK ejecting well I haven’t had to tweak anything everything works right out of the box. I just have to open the bolt before inserting a mag, or it just will not go in.
@Goesinya693 ай бұрын
Hello, coversions fit the same for 650 and 750??
@nvkulk4 ай бұрын
Works for large primers too!
@OleStanman4 ай бұрын
***JUST A WORD OF CAUTION ON OIL CHANGING***. I have a new 2022 Trailmaster Challenger 200EX and just did the first oil change at 24 miles. I put in 30 oz of 10-W-40 synthetic and it was over full. Ran engine a little to see if that made any difference and it didn't. Had to suck out about 4 oz to get it back to the correct level. I suspect engine design changes over time may require different capacities. Not much info on these Chinese engines so just adding my personal data. By the way thanks for the video and useful info.
@edlor49354 ай бұрын
Are you still selling brass
@wemcal5 ай бұрын
Great video and great looking brass
@devinvalentine57805 ай бұрын
Question… so are you saying to try and cycle your brass with no bullet from clip to chamber and see if the brass cycles?
@jonm23815 ай бұрын
Are you still selling brass? Thanks
@jonm23815 ай бұрын
This is the first video of yours that I’ve seen, I would like to get the plans for the bullet feeder that you talked about. Thanks
@rexjustis42875 ай бұрын
Thank you for a great video and the links.
@tj2726 ай бұрын
Thanks Mark, easy fix after your vid. Now into the real issue I’m having. My takedown lever is stuck in position after reinserting the cylinder in place so can not get slide back on…? Any help with this ? Thanks in advance for any guidance.
@TargetTime6 ай бұрын
Update on the trialmaster . Had to put a new engine in it. Simple gy6 150-200cc replacement. Went with the one that already has the challenger transmission attached. About 750. New motor SUCKS. 3rd carburetor replacement last week. Gets about 2 weeks . 3hours runtime maybe. 1st motor failed due to my fault. Not checking the oil
@DisclosureTvNews7 ай бұрын
I was unaware that the bullet seater/crimp die got rid of bulges or shaped the case. i was always told and thought that the resizer dies took care of all that.
@TargetTime6 ай бұрын
The bullet seat crimp die does not The factory crimp die does on the already completed round
@nanalisa9627 ай бұрын
I have the 200 challenger and it is wheel hooping on take off? At dead stop take off . It like there is something binding do you have any idea on what wrong.
@user-bv1qo7ip2z8 ай бұрын
You are awesome
@TargetTime8 ай бұрын
Thanks
@jerrywiese97229 ай бұрын
They make optical switches to replace those mechanical ones on your bullet and case feeders.
@TargetTime9 ай бұрын
Yeah in the beginning they used ardruino boards and pi I'm sure you can get a simple on off signal Switch now and wire it into the power
@hash461769 ай бұрын
How much for 9mm ,45 acp and 223and556
@aminhakimi52649 ай бұрын
What is the blue part name ?
@-CBA-9 ай бұрын
its not 50 dollars anymore lol
@hash461769 ай бұрын
Is this printable on an ender3
@TargetTime9 ай бұрын
Yes
@TargetTime9 ай бұрын
Check bucket size. But I had a red one printed on an ender 3 and I don't think it needed resized for height. Remember full infill for durability
@justanotheryoutuber52289 ай бұрын
I like it just not the idea of how it snaps on. Feel like it can come off easy
@kylereynolds899110 ай бұрын
I put mint together without that spring back in I didn’t know it was out and now the slide is stuck half way froward and I can’t get it unstuck like it locked but it won’t go anywhere because it’s not right I’m afraid to force it. It was my first time takeoff all this apart and tried to do it on my lunch 😅
@TargetTime10 ай бұрын
Ouch. I hate when that happens. I think I done that on this, a cannik, and a skyy 9mm 😄 I remember being scared on an sr9 also with it jammed halfway
@jhnstuhlmiller11 ай бұрын
I think the guy stopped working
@karlbibb241111 ай бұрын
I am no longer selling anything. Just an FYI.
@user-sd3jh5jw7z11 ай бұрын
intrested in brass....thanks
@TheonlythingIcanthinkofisthatt Жыл бұрын
Dude thank you so much
@ellenj8896 Жыл бұрын
COOL!
@redfoot69 Жыл бұрын
My portable Lee loader kit just did same thing 10 minutes aga on 1st round probably cheap pot metal from Asia since free trade started years ago
@dennisfuchs8984 Жыл бұрын
I bout one last yr !! Ive put everything threw it !! Never had Ive got any blow back in the face !! Good gun and Ill use it forever!!
@justlooking2183 Жыл бұрын
Dude thanks so much what a great idea. I looked up saw horses Vs target stands $22.99 for a Bauer harbor freight vs $80 to $100 bucks 😮
@CorneliusFahey Жыл бұрын
Bad audio. Can’t even hear what you’re saying…
@mobilesolutionsfl Жыл бұрын
Say that were a 300AAC, what spring and weight works with the brace?
@chrisorourke7697 Жыл бұрын
Do you have problems with your pistol brass sticking in your dies? Do you need to lube your pistol brass because the brass is almost too clean? I’ve followed the same procedure (lemmie shine carnuba car soap) but with the pins and I found the 9mm cases sticking in the sizing die. Spoke to Dillon about it and first question they asked was am I using pin to clean my brass? They are seeing this problem a lot and they believe the pins were cleaning the cases too thoroughly so now lubing the cases was recommended. Instead I stopped cleaning them with pins in a tumbler and went back to the walnut media method which eliminated the problem. Was wondering if I cleaned without the pins whether it would still creating a sticking condition now that I’ve seen your video?
@deganni2688 Жыл бұрын
very good idea with the saw horses - thanks for sharing
@dylanyeager5760 Жыл бұрын
So the brace comes with that special buffer tube?
@TargetTime Жыл бұрын
Correct
@fearrogue Жыл бұрын
nice
@troy9er Жыл бұрын
Been there thinking about one of these for a while now. My state sucks for us Gun owners. Illinois just sucks!
Пікірлер
What about on the 19x?
that's actually a great idea.... now I need to tripod mount it so I can shoot handgun
No words spoken and easily the best instructed video I’ve seen on this
Best video I’ve seen on this 👍🏻👍🏻👍🏻 very helpful!
Glad it was helpful!
The lee bullet feeder dies work great. Not sure with an auto bullet feeder but with the tubes similar to the mini mr bullet feeder set up. I just ordered the silver layer bullet and brass feeder. We’ll see how well they work but the pics and videos I could find the fit and finish look really good. $400 for the set with disks for 9 40 45 223 included. Veteran owned company that’s making them which is always a plus in my book
I built my panther arms AR-9 from a build kit SDI sent me and I have a big wrench for tighting the barrel nut but I don't have a vise so I got it as tight as I could without breaking the aluminium receiver.
No way is everything getting clean without pins. If I want shiny brass I decap use pins then switch to 3/16 stainless balls.
7:26 looks pretty shiny
@@TargetTime inside the pockets
ALERT 🚨 do not I repeat do not! add a whole quart of oil when doing your own oil change on your trail master .. I just did mines earlier I have 150cc engine and i over flowed it & went up the road and it was running real sluggish so I drained it back out again and put just a little over half the bottle got back on the road & it ran a whole lot faster and better
Do me Maintenance vids on trail master plz!!👍
Yeah, I can’t find the single stage kits he used to make, they were the best. Looks like he went out of business. Sucks, I will regret my entire life that I sold mine
Very useful thank you man I did touch it and you solved my problem of dead trigger
Just got my first colt mag block because I’m doing another AR nine build. For the past two years I have been using a Palmetto State Armory AR nine set up with the Glock mag dedicated lower and I honestly have not had a single malfunction thousands of rounds later surprisingly. I don’t have the bolt hold open, but it works fine. Now with my second GEN Pro mag block I’m using Colt mags and so far so good no jams or anything like that but I noticed with a full mag using my PSA upper I cannot see the mag. It is nearly impossible to the point where I am indenting the casings. Is that normal or is it just maybe my BCG isn’t really set up for Colma? It seems to function and shoot OK ejecting well I haven’t had to tweak anything everything works right out of the box. I just have to open the bolt before inserting a mag, or it just will not go in.
Hello, coversions fit the same for 650 and 750??
Works for large primers too!
***JUST A WORD OF CAUTION ON OIL CHANGING***. I have a new 2022 Trailmaster Challenger 200EX and just did the first oil change at 24 miles. I put in 30 oz of 10-W-40 synthetic and it was over full. Ran engine a little to see if that made any difference and it didn't. Had to suck out about 4 oz to get it back to the correct level. I suspect engine design changes over time may require different capacities. Not much info on these Chinese engines so just adding my personal data. By the way thanks for the video and useful info.
Are you still selling brass
Great video and great looking brass
Question… so are you saying to try and cycle your brass with no bullet from clip to chamber and see if the brass cycles?
Are you still selling brass? Thanks
This is the first video of yours that I’ve seen, I would like to get the plans for the bullet feeder that you talked about. Thanks
Thank you for a great video and the links.
Thanks Mark, easy fix after your vid. Now into the real issue I’m having. My takedown lever is stuck in position after reinserting the cylinder in place so can not get slide back on…? Any help with this ? Thanks in advance for any guidance.
Update on the trialmaster . Had to put a new engine in it. Simple gy6 150-200cc replacement. Went with the one that already has the challenger transmission attached. About 750. New motor SUCKS. 3rd carburetor replacement last week. Gets about 2 weeks . 3hours runtime maybe. 1st motor failed due to my fault. Not checking the oil
I was unaware that the bullet seater/crimp die got rid of bulges or shaped the case. i was always told and thought that the resizer dies took care of all that.
The bullet seat crimp die does not The factory crimp die does on the already completed round
I have the 200 challenger and it is wheel hooping on take off? At dead stop take off . It like there is something binding do you have any idea on what wrong.
You are awesome
Thanks
They make optical switches to replace those mechanical ones on your bullet and case feeders.
Yeah in the beginning they used ardruino boards and pi I'm sure you can get a simple on off signal Switch now and wire it into the power
How much for 9mm ,45 acp and 223and556
What is the blue part name ?
its not 50 dollars anymore lol
Is this printable on an ender3
Yes
Check bucket size. But I had a red one printed on an ender 3 and I don't think it needed resized for height. Remember full infill for durability
I like it just not the idea of how it snaps on. Feel like it can come off easy
I put mint together without that spring back in I didn’t know it was out and now the slide is stuck half way froward and I can’t get it unstuck like it locked but it won’t go anywhere because it’s not right I’m afraid to force it. It was my first time takeoff all this apart and tried to do it on my lunch 😅
Ouch. I hate when that happens. I think I done that on this, a cannik, and a skyy 9mm 😄 I remember being scared on an sr9 also with it jammed halfway
I think the guy stopped working
I am no longer selling anything. Just an FYI.
intrested in brass....thanks
Dude thank you so much
COOL!
My portable Lee loader kit just did same thing 10 minutes aga on 1st round probably cheap pot metal from Asia since free trade started years ago
I bout one last yr !! Ive put everything threw it !! Never had Ive got any blow back in the face !! Good gun and Ill use it forever!!
Dude thanks so much what a great idea. I looked up saw horses Vs target stands $22.99 for a Bauer harbor freight vs $80 to $100 bucks 😮
Bad audio. Can’t even hear what you’re saying…
Say that were a 300AAC, what spring and weight works with the brace?
Do you have problems with your pistol brass sticking in your dies? Do you need to lube your pistol brass because the brass is almost too clean? I’ve followed the same procedure (lemmie shine carnuba car soap) but with the pins and I found the 9mm cases sticking in the sizing die. Spoke to Dillon about it and first question they asked was am I using pin to clean my brass? They are seeing this problem a lot and they believe the pins were cleaning the cases too thoroughly so now lubing the cases was recommended. Instead I stopped cleaning them with pins in a tumbler and went back to the walnut media method which eliminated the problem. Was wondering if I cleaned without the pins whether it would still creating a sticking condition now that I’ve seen your video?
very good idea with the saw horses - thanks for sharing
So the brace comes with that special buffer tube?
Correct
nice
Been there thinking about one of these for a while now. My state sucks for us Gun owners. Illinois just sucks!
nice
Would it fit on a 19x?