ZX10r Clutch fix. Finally sorting the Kawasaki's rattle. Slipper clutch explained
Автокөліктер мен көлік құралдары
Dave finished his 2004 zx10r road bike ages ago, but the clutch rattle was always annoying, so finally he's got the parts to fix it.
See how he strips and rebuilds the clutch, and how the slipper works and can be adjusted.
obsessionengineering.co.uk/shop
Пікірлер: 76
Very interesting to watch as somebody who is trying to learn and understand more about the mechanical side of motorbikes 👍
@obsession_engineering
8 ай бұрын
I try to keep it simple, or at least understandable!
Very good video! Very well explained.
This is a brilliant video. Thanks Dave !
There is a bodge method of stopping the clutch spring rattle (recently had to do it to my CB500) which works but is at your own risk. Simply insert one washer of the correct diameter under one end of each spring (thick enough to be a relatively tight fit) and then tack weld the washer in place. It worked for me and I believe some of the CB500 racers do it too so it can’t be all that bad. 🤞
Great information & thorough work Dave! Busy man prior with BSB & now you’ll have heaps of time to work on your own bikes in winter 😉 Champion spannerman🤙
Love the in depth videos Davie 👌
Excellent! interesting to watch with handy tips.
Excellent technical video! Cheers
Morning Dave……top notch work….great video,👍👌🇮🇲
KEEP UP THE GOOD WORK
Great video, very informative, I like that you can change the slipper action by the plate gap & springs.
Thanks Dave, enjoyable start to a Sunday. Off out for a ride in a while, think I might head to Dartmoor 🤔
Another very interesting video 👍 love all your work I see you around the BSB paddock and a few times at Scarborough after watching your videos I all most feel I know you it’s a strange thing 😂 keep them coming 👍👍
@obsession_engineering
8 ай бұрын
Come and say hi next time 👍🏼
That was a good watch, and very interesting. Especially the bit about the ‘kit’ clutch, and tuning the slipper clutch.
Very informative, thank you.
Very interesting, great explanation 👍😎
I have a gen 1 zx10r, got it with about 15k miles give or take. I have 70k miles or so of hard riding lol love the gen 1 !!!!!! I had a issue with clutch kits burning up, I read about the muzzy zx12 clutch basket and hub mod to give the clutches more oil, did it to my gen 1. A complete difference and never had a burnt clutch again.
@obsession_engineering
8 ай бұрын
Very useful to know, thanks
Great video as always . I just put ear plugs in when I had mine as after 3 years I still hadn't found a new basket.
Hi Dave, really gets my Sunday started 😂 love all your videos and these technical ones are super pleasing and interesting to watch. But I have one question... when are you making a video about you're Aprilia Tuono v4??😅 grtz from the Netherlands 🇳🇱 and keep up the good work!!🎉
@obsession_engineering
8 ай бұрын
Eventually, once I get time... I may go riding this afternoon, to remind myself how ace it us 😁
Love this video's. Thank you.
Great informative video,,I prefer the older analogue bikes,, plenty of power and a lot less wires and pumps 🙂,, I've an 06 Gsxr 1000 aswell as an SV 1000 which has a rattling clutch 😢 thanks for posting this video ☘️☘️☘️☘️☘️☘️☘️☘️ from northern Ireland
The 1st steel, anti-judder plate, also fits the GSXR 1000 K1, K2's which helps the GSXR get off the line, by solving the snatchy clutch issue.
@JameseyB555
8 ай бұрын
Had same problem with my k4 works like a dream with the zx10 steel in
@youmisterrob
8 ай бұрын
Very interesting
@Herringfish101
8 ай бұрын
I throw the jutter spring in the trash. APE track king clutch. APE basket. Works like a champ.
@apieceofreese48
5 ай бұрын
i’m having this snatchy clutch issue on my k7… any idea?
I had awful trouble with my gen 1 clutch until I fitted a sigma slipper clutch system from a 2008 zx10r. You have to die grind out the clutch cover 1mm. Result is 🤯
I spy with my little eye, something beginning with ZXR. My all time favourite bike, well apart from an old school CB 9.
Good video, but I expected that you will fix "the old" clutch basket (springs) and show us how to. But you replaced for another part. Not all of us has possibility to change clutch basket. We need to repair original part somehow. Can you do another video specially how to repair this rattle basket please?🙏
Nice informative video Dave i guess you had already taken it apart to get the number from the basket..🤣
@obsession_engineering
8 ай бұрын
Yes, although it was 18 months ago!
man i wish there was a sound sample in this video. i have a zx600p and i have a suspicion that it maybe has the same problem.
@obsession_engineering
Ай бұрын
The 600 motors tended to be a bit mechanical (some say noisy) and weren't unknown for cam chain tensioner issues. Not know clutches to be an issue though
I am about to pull my clutch out of my 05 zx10r for the same reason.
Nice job!! Do certain clutch baskets just not rattle, or will the one you sourced also start rattling eventually?
@obsession_engineering
8 ай бұрын
Eventually they all wear, guessing the previous owner didn't blip much on down changes which wears them faster
love the videos but on this one i noticed the footrest hero blob is missing 😂
Does the 636 also have this problem? I have a B1H 636 2003
🤔 after the montage AND refilling oil "why raving the engine/rpm?" neither the clutch-leaver at "basic" rpm (1200min^-1) i spot at a repair like here that the owner let the engine run and move the clutch-plate by the leaver ~5min. , clean-up the workspace and again he told me that should be the oil-viskosität ...powertrain was "hand warm" not hot !
I don't think the springs actually wear down on the ends. I think they just collapse from age and use.
so were do we get 95 zx6r ignition box
Hi can I ask a question I have a 2006 zx6 636 put a new 3 rd gear in putting clutch plates back and noticed the plates slide back and forth quite a bit never noticed before is that normal cheers bob
I would not give my 04 zx10 up for any other boke on the plannet 🤙
What sort of mileage would you expect from the springs if only used on the road on the 04 and 05 bikes
@obsession_engineering
8 ай бұрын
Very much depends on how it's been ridden, dumping the clutch on down shifts, especially on track causes more problems. On the road I've seen 40k mile bikes with no issues
You’ll b in the same position in no time if that’s a standard basket maybe an APE clutch woulda been better ?
Can the springs in the basket be replaced
@obsession_engineering
5 ай бұрын
Not easily, and the basket would need material replacing too
I’m thinking my 05 Zx10r is Needing a Clutch. I pull the clutch in in Neutral and the Rear Continues to spin. It doesn’t physically Slip I can’t feel it that is. Any Recommendations For Clutches?
@obsession_engineering
6 ай бұрын
Common to get clutch drag if the hub or basket are wearing where the plates run on them. Might be worth having a look at that first. The oil will cause a little drag too. I'd stick with oem parts as far as possible, they work well when there's no wear issues
How do you know all the little tips and tricks to get everything done on this specific bike? I thought racers just ... raced?
@obsession_engineering
7 ай бұрын
Went I raced one of these I found most of the issues, it was a while ago but some things you never forget 😂
I have a 2006 z750 and when it's cold or warming up I often get clutch honk,,any idea what the problem might be?
@obsession_engineering
8 ай бұрын
I've never looked at z750's so not sure if there's any regular issues.
@johnskarvelis6936
6 ай бұрын
2006 Z750 95K km, I had similar noises when cold in neutral. I checked /replaced the ball bearing that sits on center of pressure plate. Very easy DIY job. The bearing type is SKF 6001.
7:53 when bike is running is that rattle noise gone when u pull the clutch in and than when u let the clutch it starts rattling again?
@obsession_engineering
4 ай бұрын
When the back of the basket wears, they rattle all the time
@chevchelios7342
4 ай бұрын
@@obsession_engineering in my question i explained the rattling on my triumph.. its not that bad.. its more noticeable on a cold engine.. 😁
Where did u get the clutch cage washer ? I can’t find it anywhere
@obsession_engineering
8 күн бұрын
Lucky ebay find after lots of searching!
@Truthsearcherforever777
8 күн бұрын
@@obsession_engineering I think ima start making parts my self
@Truthsearcherforever777
8 күн бұрын
@@obsession_engineering when u had the spring loose, what did u experience mechanically ? Did u had a hard time going from neutral to 1st gear on a stop light on the street? My ZX10R 04 does have that problem some times on the street that’s why I stay holding clutch on stop light n never putting it on neutral.
Why is the replacement basket better than yours spring wise but the other parts were worse than yours
@obsession_engineering
8 ай бұрын
It's a mystery!
Does a 07 ZX10R have a slipper clutch?
@obsession_engineering
2 ай бұрын
Yes, all zx10r have a slipper clutch
It's a shame those springs can't be replaced.
@obsession_engineering
8 ай бұрын
It's more about the backing plate which also wears
@markbteeps
8 ай бұрын
@@obsession_engineering ah, yes, that makes sense
Alternatively, convince yourself it's just a weird Ducati and the clutch clatter is normal... 😁
Thanks for the upload. I really enjoy your informative style of video and seem to be able to take in so much of the detail, even though I'm unlikely to get my hands this dirty in my advancing years. Ever thought of becoming a lecturer in engineering? Back in my youth we had such dull lecturers. Can't remember a thing they taught me!! 🥱
@obsession_engineering
8 ай бұрын
They'd soon realise I was winging it 😂