I used your videos to rebuild my X5 transmission.

As always , amazing Garry. Thanks for teaching.

Thanks for these videos, they're really helpful. I'd love if you gave a rebuild/reassembly video for this same transmission. *LIKED*

@GaryFerraro

5 ай бұрын

will keep that in mind

Oh shit, this is the one I have been waiting for. 8HP70 and a 90 is what I want to see.

@GaryFerraro

Жыл бұрын

Not a bad unit to work on just parts are hard to ge

Thank you for your video and knowledge.

Muchas gracias por tus video 👍

Pretty tricky one there

One acre of parts for a f. gearbox.

A Nag1 to 8 speed swap would be nice!!!

nice

Longest pan I've ever seen.

No matter how many times we change the atf fluid.If there's wear on the internal components of the automatic transmission,changing the atf fluid will not resolve it and the car may not even drive anymore.Do you agree?

@FishFind3000

Жыл бұрын

I guess that depends on what’s worn and how bad. If you have no more friction material left then when you flush it you won’t have the gritty fluid to help and it could make it worse. You should change the fluid before you have problems. But changing fluid can resolve issues, I had a transfer case in a f25 bmw x3 that would shutter when turning and doing a fluid swap fixed the issue.

@Dernie1000

Жыл бұрын

Great video Gary! Do you have a favorite ZF transmission?

Great video Gary! Do you have a favorite ZF transmission?

@GaryFerraro

Жыл бұрын

I like the ZF6HP26 units

@johnramsey6604

2 ай бұрын

Isn't that the transmission that came with the 2012 ram?

Can't believe they have that chain in there.

@GaryFerraro

11 ай бұрын

off axis pump, a lot of Transmission have that now

What was the total cost in this rebuild for the parts? Great video too 👍

My zf850re @ 60k will pop out of reverse when backing out of my garage? Any ideas?

What pick are you using for the snap ring? Looks much stronger than mine

@GaryFerraro

Ай бұрын

what time in the video am i using it?

You probably seen both the 8hp70 and 8hp75 for the V8 Ram 1500, do the housings have the same dimensions and mounting patterns ? I want to swap my 70 for a 75 and use the 8hp70's electronics so everything is plug n play.

Hello Gary, thanks for this very interesting video. Nice to see how skillfully you work with these complex gears. I also have a ZF automatic, I think the 45 (BMW F36) I also have a problem with my zf automatic transmission. As I roll the car towards the stoplight, I hear a grinding noise until I come to a stop. When I let the car roll towards a traffic light and I hear the noise and put it in neutral, the noise is gone. So it must be gearbox i think. It still shifts well, a little harsh at times, but they all have that in the long run. What do you think, when you read my story? regards.

@GaryFerraro

5 ай бұрын

Ok, Question, while standing still foot on the brake car in drive or reverse, do you hear the noise? if you do, when you put it in Neutral or park does the noise go away?

@Tinnntin

5 ай бұрын

@@GaryFerraro no, I really only hear the noise when slowly coming to a stop at the traffic light

Great videos like always. Which zf transmission are best .

@GaryFerraro

Жыл бұрын

I like the 6 speeds, they have common issues like they all do but the units don't really blow up, rarely have hard part damage

@harvrindrsingh

Жыл бұрын

@@GaryFerraro thanks for quick reply. What like common issues they all have.

@GaryFerraro

Жыл бұрын

@@harvrindrsingh The 6 Speeds have rear stator bushing wear and solenoid problems

Do you rebuild transfer cases that have clutch’s in them?

@GaryFerraro

Жыл бұрын

Not anymore, shop is way to busy so now i just purchase rebuilt ones

Any idea where i can get a spare clutch D hub shell from? Building an 8HP70 currently.

@zach9373

4 ай бұрын

Never mind, Erikksons hooked me up!

In the original bmw workplace manual for 8hp45/70 they diddnt say to replace the bolts only the sealant ring arount them how do u feel to use them again? I work on the same transmission for a project. And indeed some parts are difficult to find. Thanx in advance ur videos help me alot

@GaryFerraro

Жыл бұрын

I think you will be fine

Hey gary i got a 8hp45 bmw f30 320d it was stuck in park stripped down the box and found p2 carrier spinning on input shaft replaced that now when changing to 6th it hesitates and goes back to 5th and then limp mode gear ratio error 5> x any advise will be greatly appreciated

On assembly if you have the torque info this would help out a lot.

@GaryFerraro

8 күн бұрын

do you need any torque spec

@danrazumovsky

8 күн бұрын

@@GaryFerraro yes, what is the oil pump bolts screw in for the final bolts.

@GaryFerraro

8 күн бұрын

@@danrazumovsky The bolts that hold the pump to case?

@danrazumovsky

8 күн бұрын

@@GaryFerraro yes.

@GaryFerraro

8 күн бұрын

@@danrazumovsky ok, I dont have the info in front of me, but i believe it's about 50 Inch pounds then an extra 90 Degree turn. It's either 45 or 90 degree turn

Question for anybody knowledgeable here....sometimes my 8HP95 will shift from 2 to 1 while creeping forward after coming to a stop. The engagement from 2 to 1 is a very hard engagement. Speedometer reads around 1-2 mph when then happens. Is this normal?

@snowsaysahhh3037

9 ай бұрын

hi, that's bad programming on the transmissions part had that aswell and chose to just remove 1st gear all together in software so it doesnt do that anymore.

Great video, question for you. Where did you get that test plate?

@GaryFerraro

Жыл бұрын

The guy i was rebuilding them for had, i would think you could probably get them from the dealer

@josemiranda9626

Жыл бұрын

@@GaryFerraro thanks

What is the proper name for the rear seal connecting to the shaft

@GaryFerraro

Жыл бұрын

That is the Name, Rear Seal

I have a 3-4 flare sometimes.. wondering if my D clutch is failing?

@snowsaysahhh3037

9 ай бұрын

probably but also could be just that the clutch pressure adaptives are maxed and cant command more pressure a quick transmission readout software wise could help if the clutch fails the trans will throw a code since its super smart and knows if something is wrong

Gary, I just used your video to tear down and rebuild my hp70. When I installed it my dash cluster says its not in park and is in limp mode. Any ideas you could offer would be greater appreciated. Great video btw. Thanks

@GaryFerraro

Жыл бұрын

Did you hook up the park piston to the linkage inside the trans?

@ronswartz3695

Жыл бұрын

@@GaryFerraro yes sir

@ronswartz3695

Жыл бұрын

I also ohmed the solenoids and they are in range.

@GaryFerraro

Жыл бұрын

@@ronswartz3695 scan it for codes, if any clear them and see if it's ok

Ever had an 8HP70 with a harsh at times 2-3 shift?

@GaryFerraro

Жыл бұрын

I have had some with harsh downshifts, i reset the shift adapts and it fixed it

@snowsaysahhh3037

9 ай бұрын

yup bad adaptives do that for you. reset, if its still happening a tune up on the transmisson will most likely fix that.

Gary, quite recently we brought my 2016 1500 ram, with this transmission, into the shop because of a card in bike stokes sound when I hit the 30-40 mph range. It would go away upon manually shifting or putting it into neutral. To me, everything pointed to the MDS, even found a video that sounded exactly like the problem I had and it was the MDS.. So, they brought it in and said no, its the transmission pump.. its chain driven and when we put it up on the lift we can feel the pump shaking. But watching this video leads me to believe how could they feel the pump shaking especially where the transmission is on the dodges... they said when on the lift they replicated the speed and could see it shaking, could feel it shaking... nevertheless they diagnosed the problem as being the oil pump is shot. Is there any way that the chain can slack and cause a card in bike stokes kind of noise??

@GaryFerraro

Жыл бұрын

If it were pump you would hear it all the time, the pump is always turning. So you hear a noise in drive and reverse and goes away in park and neutral?

@allainiegoad4836

Жыл бұрын

@@GaryFerraro So I only hear the "ticking noise" when I am decelerating and enter into the 40- 30 mph range... the sound will come and go. But if I use the manual shifters on the wheel the sound goes away.

@allainiegoad4836

Жыл бұрын

No sound in reverse or in park.

So was it a 70 or 90?

@GaryFerraro

7 ай бұрын

This was a 70

@240sxandcivic

7 ай бұрын

@@GaryFerraro is the 8hp90 more different or almost the same?

@GaryFerraro

7 ай бұрын

almost the same@@240sxandcivic

Have you use nokia 3310 to film this ?

@vladthegladiator

27 күн бұрын

😂