As a retired stage rigger, I think it should be emphasized that these ideas are for decorative use and should NEVER be used in a "life safety critical" situation or where something might fall on someone. Drilling a bolt seriously weakens it and welding on it would further weaken its temper and strength. Welds on equipment that must be safe should be xrayed or magna-fluxed to check the bond of the weld, or load tested to at least 5 times the expected loadFor side ways loads, only forged eyebolts should be used with flange bases.

@E-rigging

2 жыл бұрын

Agreed! These are super creative ideas. Should come with some sort of disclaimer, though. Relying on something like that trellis system to support any amount of load or force could cause serious injury or worse.

@GTrainRx7

2 жыл бұрын

Pretty sure that is a given, although if you don't know welding you may not realise the welds are ... average, at best.

@comesthru

Жыл бұрын

Good comment. I do not trust any untested trick such as this.

not sure what the cool idea's were but this guy is sure good at drilling a straight hole through a bolt.

@mihailpetrovici5044

4 жыл бұрын

😂😂😂yeaa

@johndobbie528

3 жыл бұрын

If I was counter drilling a bolt just held by the thread in the lathe it wouldn't be much more accurate!

@marcelsincere9933

2 жыл бұрын

i know Im asking randomly but does anyone know a trick to log back into an instagram account?? I was dumb forgot my account password. I appreciate any tips you can offer me!

@jaxenkarter4038

2 жыл бұрын

@Marcel Sincere Instablaster =)

Muy buenisimas ideas,gracias mil.

I really enjoyed the technique of jamming the rough cut frayed end through the small hole with camera cuts.

Buenos trucos

Absolutely you are right.before this video we don't know about your extraordinary knowledge.keep all in your mind.

Loved them. Especially #3 Keep them coming!

Excellent congratulations Muito obrigado Thanks

Super.... Good job 💐👏😂

Wow so amazing videos

Great ideas . . Thank you very much Sir

Awasome Brother

Good 👍👍👌👌

You're right, I hadn't seen these until now, but I'm certainly keeping them in-mind now! I'll use real crimpers, though...

Thank!

Good 👍👍👍👍👍

Thanks

Harika ...

GENIAL

Perfect 👍😍👌❤️💯🌹

Amazing creativity. Superb 👍

Looks great. Hope it hold high tension. :) thanks

Когда в мире коронавирус и нечем заняться дома 😁

Good

Nice

THIS IS A BOLT ?? MAKE A SPIN ?? 🤣👍🏻

Top!

Доктор Дью оценил

Nice idea i like it too much,,i can make with my home,thanks for your idea bro

@mrsunyofficial

4 жыл бұрын

Hallo Bro!

Zaberdust

i need steel cable for something. let me secure it to drywall.

@ndoil515

2 жыл бұрын

....it's concrete.

@bobtahoma

Жыл бұрын

I don’t think you should be doing anything with a drill!

El cable no está bien sujeto ...dé nngun modo confiaria colgar algo

Great video

Nice video! Direct like 👍

I'm at 4:19 and I just realised I've probably seen at least 1 idea fully realised, and I couldn't tell you what it was supposed to be

Show us wire rope ideas without the power tool please. Thanks.

круть!!!

@user-te4qw4nu2u

4 жыл бұрын

아주좋아 정말좋아최고

Very good 👍

I came for the bolts... i stayed for the beats.

Good nice mr suny

Mega work

Only if making those length wise holes this easy

This should be labeled, "What me drill holes through bolts."

Cable specialist are charging us a fortune 👍👍👌

👍👍👍👍👍👍👍👍👍👍👍👍

Некоторые идеи далеко сомнительны...

Nice😀😀😀

And absolutely never want to see them again.

You're wrong. IKEA had a product like this about 8-10 years ago. I have a couple of them in my house.

What brands of drill bits are you using ?

@krushnamohansahoo5633

4 жыл бұрын

Mitsubishi

Очень сильно круто 👍

@pedropedrito7280

4 жыл бұрын

Buenas ideas grasias

Go to all that effort using mild steel parts that will rust out near in the salt air instead of using 316 stainless steel.

These strike me as a good solution only if you have $45,000 worth of machining equipment, but not a $0.45 steel cable eyelet.

All of this is easier using ferrules and turnbuckles.

Last one: just drill the hole smaller in that metal?!?

Bikin alat buat bending U aluminium

Да не мучайте вы тросик! Заплетите, сделайте красивую, прочную и главное быстро, петлю и цепляйте куда хочется. Нет, если хочется посверлить .... Чужое хочу, я уважаю. Спасибо.

👍

SUNIFICATION YOUR LIFE MY FRIENDS !! 😆👍🏻

crimping the end of the wire was the weakest part of the process. but as ideas go that was good

Здраааасьте)

@mrsunyofficial

4 жыл бұрын

Hi Bro!

@demoralizator4102

4 жыл бұрын

@@mrsunyofficial Доктор Дью ждёт Вас на "прием" с такими самоделками.(Ютюб).

💋❤ Zürich Albisrieden dä rosche 😉🤠

these can be useful for clothes lines arthur linden

Hi

hey i need a simpler way to connect a cut wire than this on 4:08

Самоделки ни чем так как это 1трудоемкость,в магазине все эти крепления и растяжки есть

Зачем ты это снимаешь?🤦‍♂️🤣

@user-pk5xb5mh7p

4 жыл бұрын

Для доктора дию

عينخبش ز

Я так и не понял нах это надо

@yurasa1

4 жыл бұрын

А чтоб просмотры ему были и счастье! 😄

01:09 06:25 03:19

First two. Pointless. Why not loop through an eyelet if you have crimps then just tight eyelet down. Going away it will tighten and going down the wall it will wrap and tighten. Just drill a hole then put wire through the bolt, tighten bolt. Can even drill it through close to the head and tighten down with a nut. Doesn't even need a hole drilled Pull tight, tighten nut then really tighten by screwing in the bolt. I would place a washer next to the bolt head. Loads of quicker better, easier ways, with none of the tools. nut crimp; it's ok but why not just splice the small easy stuff. If you saw this video you can watch one on splicing. Not sure what the last one even served a purpose for besides looks. This video shows you how to achieve something using more material, more tools, more time, and more effort to achieve one common goal. Good ideas in general just not good ways of doing them

Ого, сколько дерьмовых идей! Процветания Вашему каналу! 👍

@Texno_Login

4 жыл бұрын

дАрмовых?😃😃😉😉

@Alexander_Semenov_1986

4 жыл бұрын

@@Texno_Login нет-нет! Я не описАлся)

Why so much work? Easier to buy a talrem and a pair of cable clamps. Cheaper and faster.

👍👍👍👍👍👏👏👏👏❤❤

Boludez

The

About the third one...just buy a gripple.

dude, you're drilling into a ciment wall with an ordinairy spiral drill (that will be blunt after) in stead of a stone drill, poor example

I had a feeling this was gonna be dumb and sketchy

These are really bad ways to terminate wire rope. None of them would pass any form of industrial inspection, and - as JP says - none of them should be trusted to hold any kind of load. It went wrong when he started to weld threaded rod to a nut, and just became nastier from there.

You titel is wrong i have seen them before

@kharikrishna2937

3 жыл бұрын

Hi

@kharikrishna2937

3 жыл бұрын

Super video

No

Poor

time waist

what a bodger.

This is not good idea man

😂😂😂👎👎

Bad ideas

😂 Please, don’t waste your time with any of this nonsense!!

@mrsunyofficial

6 ай бұрын

Ok Bro

Good

Nice