You rock. This worked perfectly!

@michielcornelissen2430

8 ай бұрын

good to hear! have fun!

@petesha5101

8 ай бұрын

Maybe you can do a video showing actually how the connections are made. The Michael guy just keeps saying follow the schematics, which is not clear enough for many of us. The bought the adapter and a 433mhz receiver. Have the wifi version of reolink but not understanding what's connecting the reolink doorbell to the adapter and so forth.

Nice work - thanks for sharing. I did this slightly differently, by fitting a 3A 12V transformer to run everything. I cut the wiring to the bell push and chime, then used the +12V to power the receiver and the Reolink doorbell. Once that was working I wired the chime between the receiver's "Common" and "Negative", and connected "Normally Open" to "Positive". It worked okay, but I have a "ding-dong" bell which only rings when power is connected or disconnected. To make it ring three times, I installed a timer relay between the receiver and the chime, and set it to On for half a second and off for a second. End result, I get a nice "ding-dong, ding-dong, ding-dong" when someone presses my doorbell :) Thanks for sharing the secret about the availability of the receiver relays! The one I used was a little different, but the key is to find one that's advertised as using the "Princeton" or "EV1527" protocol.

@thomasboeker1298

29 күн бұрын

Hi @electrickery. Which timer relay did you use? Do you have a link for me? Thanks

can you power reolink bell with same transformer

Does this also work with the new Eufy doorbell? I need extra chimes for my parents.

Hi! Great video. Looking for a solution like this. One question tho, i dont have the “ding-dong”-chime but the mechanical tring chime. What do you expect here. A very short ring? How long will the relay make contact? Thanks in advance!

@michielcornelissen2430

10 ай бұрын

Hi! The relay makes approx 1-2sec contact. Long enough for tring chime. !

Nice! Do you know if there is something similar with Zigbee protocol?

@michielcornelissen2430

Жыл бұрын

Hi Joey, the doorbell is sending a 433 signal, so you need a 433 receiver. Zigbee will not work.

Hi Great video, Is it possibel to us the DC power adapter that's is supplied with the Reolink doorbel, to power the doorbel and this 433 reciever?

@michielcornelissen2430

9 ай бұрын

Don't think there is a power adapter supplied with the Reoling POE doorbell. There is a power adapter supplied with the WIFI version, but this is 24V DC. You cannot use this directly with the wireless receiver, since this needs 12V DC.

It's a good solution but what I really wanna do is solder in a second or throw on top of the existing button a second GPIO button that somehow shorts the 2 AC wires from my existing 10W transformer, then I power and leverage video via POE. Reliability of analog but with the convenience and features of digital - haven't seen it done yet but I'm sure it's possible without a relay - just need to engineer a way to terminate the AC wires and short them while keeping the rest of the device intact

Danke für das Video. Würde es gerne auch so machen, habe aber keine Möglichkeit den Empfänger mit einem 12v DC Transformator zu verbinden. Ich denke eine MN 21 12V Batterie wird nicht ausreichen um den Impuls für den Gong zu generieren, oder?

How do I connect my Reolink wifi camera door bell to my Nicor tansformer/chime system? When I connect the 2 wires to the camera my house door bell chimes constantly. How do I turn off the house door bell chime? I have the Reolink chime door plugin chime.

@michielcornelissen2430

4 ай бұрын

If you want to connect the chime, follow the instructions in the video: You need an additional receiver.

I watched the video on that Ali express link and they had two button activating the switch. Does this mean I can have two reolink doorbells on the same 433mhz receiver?

@michielcornelissen2430

11 ай бұрын

Yes, with some of the receivers, you can do this

Can you go way more into detail on this? In the end you just have it set up on a piece of cardboard. Can you show it set up and used normally? Can you also show what 12v DC adapter you used with a link to where to buy it? Thank you.

@michielcornelissen2430

Жыл бұрын

The setup in the electrical meter cabinet is less clear than the example shown. You can use following 12v adapter: www.amazon.nl/dp/B01G0Q3RWU Hope it is clear!

Ran into 2 issues, 1. My doorbell chime wires had to be shorted to power the Reolink doorbell. So I needed a 2nd power source for the chime. I end up using the adapter from the reolink doorbell package. 2. The DieseRC 433Mhz Universal Wireless Remote Control that was linked did not want to learn the signal from my Reolink doorbell(wifi version), not sure if it is because Reolink changed it or something. However I then remember I had broadlink pro with RF remote. I end up using that through the home assistant integration. non-issue issues 3. There is no way to set the chime that was included with the Reolink doorbell on a schedule. Because of that, if I were to have succeeded in connecting the Reolink doorbell directly to the DieseRC 433Mhz Universal Wireless Remote Control, I would have no way to control when it snoozes without another smart switch.

Hi nice work... I have a question so my existing chime has a transformer and is connected to the electrical current and if i connect this adapter 433 mhz need to connect it too another 12v adapter?

@michielcornelissen2430

11 ай бұрын

Hi thanks for your question. The transformer of a chime is in most cases AC and higher voltage. The needed voltage for the receiver is 12V DC.

@user-zn8yb9gk2h

11 ай бұрын

@@michielcornelissen2430 in the video the red wire of the 433mhz adapter (common) and the black wire that comes out of the chime go to the button of the doorbell to give it power?

@michielcornelissen2430

11 ай бұрын

please have a look at the schematic. The 433 receiver needs power from 12V DC poweradapter. The other 2 wires from the receiver act as the doorbell switch.

How far can the 433 Mhz universal wireless switch be from the Reolink doorbell?

@michielcornelissen2430

9 ай бұрын

Quite far. 20m if not too obstructed. But you can test this before buying the wireless receiver. You can test it with the supplied Reolink chime.

In case I have the 900Mhz version, is there a receiver available somewhere for pairing? And are you sure it is 900 or 868 Mhz?

Do you have a link to a suitable 433Mhz receiver that would do this? Thank you.

@michielcornelissen2430

Жыл бұрын

sure: nl.aliexpress.com/item/1005005207698624.html

@GrayGlove

Жыл бұрын

@@michielcornelissen2430 thank you. I’ve ordered one now.

Thank you for the instruction. Will it work with both Reolink wireless chime and the existing one?

@michielcornelissen2430

11 ай бұрын

Yes, they both work simultaneously

@khoihvm

11 ай бұрын

@@michielcornelissen2430 Thank you. I appreciate it. Will work on mine

@EarlBalentine

4 ай бұрын

I can't get my wifi Reolink DB to work correctly. As soon as I attached the 2 wires to the Reolink the existing house chimes non-stop. What am I doing wrong? I'm replacing my Ring2 doorbell and it work fine.

@khoihvm

4 ай бұрын

@@EarlBalentine Have you checked the Normal Closed or Normal Open connection? I think it might be the case

I followed the schematics and it all works. The only thing is that the ding-dong sound of the chime is slower than before. Did you perhaps manage to solve this?

@michielcornelissen2430

11 ай бұрын

I do not have that issue with my electronic chime.

@harryw442

7 ай бұрын

It could be that your existing doorbell transformer isn't big enough (unable to provide enough electrical current). Usually the doorbell transformer is 5VA or 10VA. Try to use the 30VA (12 - 24V, 30VA).

What wires are used? Is the little remote attached to the home doorbell chime after the connection is made? I did purchased the adapter and little remote you suggested but I have no clue what to do next. Is it possible you could do a video actually putting this together? Sorry I am a 63 year woman who is non-savvy. Thanks for reading this.

@michielcornelissen2430

8 ай бұрын

the schematic how to connect the wireless receiver to the power source and doorbell is shown in the video. you might need a savvy-er person to connect it..

I use this method however the module is not being programmed to the RF signal coming from the reolink doorbell. I had to use another wireless doorbell and now it is connected to the old chime. The downside is that I have two doorbells connected outside by the way the boys can be powered by a battery 🔋

Excellent idea! Just ordered a similar 433MHz receiver (your links don't show results).

When you say "disconnect the doorbell switch" .. how will the Reolink be powered (wifi version) ? it still needs the 12V from the existing doorbell transformer..

@michielcornelissen2430

10 ай бұрын

You just need to connect the Reolink to the existing ac transformer according its instructions. The chime needs to be connected to the new wireless receiver that powered by a new 12v dc transformer.

@d2xfd2xf93

10 ай бұрын

thanks@@michielcornelissen2430 !

@nemon729

9 ай бұрын

?chime donot need to be connected to transformer just the 433mhz wireless receiver

i have 433mhz relay powered with ac/dc 12 v adapter to power it and a trivolt transformer 1) can i power reolink wifi bell directly to transformer 16v or 24 v ? 2)how do i power and connect chime to relay no and com port ? appreciate help

@michielcornelissen2430

9 ай бұрын

The 433MHz receiver needs to be powered with a 12V DC source. If the existing adapter for the chime is same, then no issue, but normally, the doorbell chime is powered by an AC adapter.

@nemon729

9 ай бұрын

thanks the doorbell chime donot have own transformer itis connected to old 10v transformer which change to trivolt transformer need help how to wire connection and power reolink bell@@michielcornelissen2430

@nemon729

9 ай бұрын

relay has power with ac/12v adapter and sync with reolink bell

@nemon729

9 ай бұрын

thanks

Sorry, PLEASE a questions... Video Doorbell Reolink is compatible with 12 volt DC, say DC not AC and no DC 24 volt????

@michielcornelissen2430

6 күн бұрын

@@raulc.s.7103 hi Raul, the wireless receiver needs 12V DC e.g. from a 12V DC transformer

can you link the amazon products id need

@michielcornelissen2430

5 ай бұрын

sure, for example: www.amazon.com/DieseRC-Universal-Wireless-Receiver-Transmitter/dp/B098WGK35L/?th=1

@Michiel Cornelissen - Link to Wireless Module is broken...

@michielcornelissen2430

Жыл бұрын

Yes, thank you for highlighting, receiver module for example: nl.aliexpress.com/item/1005005207698624.html

@martinoptilon9915

Жыл бұрын

You from Scandinavia with that last name? Svensk, Dansk eller Norsk? :-)

@michielcornelissen2430

Жыл бұрын

@@martinoptilon9915 No, Dutch ;), you?

@martinoptilon9915

Жыл бұрын

@@michielcornelissen2430 Zweden :-)

from the video, what powers the reolink doorbell?

@michielcornelissen2430

9 ай бұрын

There is a power adapter supplied with the WIFI version, this is 24V DC.

@winsorespadilla6257

9 ай бұрын

i have a wired connection doorbell and is planning installing these. will this work? i really wanna use the existing chime. thanks​@@michielcornelissen2430

Solution is for PoE version the same!

Where to buy this module?

@michielcornelissen2430

8 ай бұрын

see the links in comments

wheres the link to buy the module?

@michielcornelissen2430

4 ай бұрын

Examples links: Module: www.amazon.com/DieseRC-Universal-Wireless-Receiver-Transmitter/dp/B098WGK35L/?th=1 12V adapter: www.amazon.nl/dp/B01G0Q3RWU?ref_=cm_sw_r_cso_cp_apin_dp_Q612YFDR39EAHV9Z3YPQ12V

Is it possible to mute or lower the outside chime ?

@michielcornelissen2430

10 ай бұрын

Yes, in the doorbell audio settings, you can turn ringing volume off

@mikej2608

10 ай бұрын

@@michielcornelissen2430 thats only the inside chimes option … I need the actual door chime volume lower or off completely

@michielcornelissen2430

10 ай бұрын

No, that option disables the sound on the outside. The standard inside chime can be disabled by just not plugging it in.

@mikej2608

10 ай бұрын

@@michielcornelissen2430 I’ll have a look at then 🫡🤜🏻🤛🏻

Where can I buy the relay?

@michielcornelissen2430

4 ай бұрын

See links in the comments

Hi is this module have to conect on power all the time?

@michielcornelissen2430

Жыл бұрын

Yes, the module needs power to be able to look for the wireless signal

@manuelcardona1723

Жыл бұрын

@@michielcornelissen2430 and can be connected on any doorbell brand like swann, ring, blink? ect ect ect.

@michielcornelissen2430

Жыл бұрын

Sure, any chime that is activated by supplying power

@manuelcardona1723

Жыл бұрын

​@@michielcornelissen2430ok thanks for the help.. the last think to understand what about the wires to the doorbell becuse my is wired...or the diagram you show y with the doorbell baterry to get power on doorbell...

@michielcornelissen2430

Жыл бұрын

Just need to replace the old doorbell switch with the wireless receiver. This will activate your existing chime.

Examples links: Module: www.amazon.com/DieseRC-Universal-Wireless-Receiver-Transmitter/dp/B098WGK35L/?th=1 12V adapter: www.amazon.nl/dp/B01G0Q3RWU?ref_=cm_sw_r_cso_cp_apin_dp_Q612YFDR39EAHV9Z3YPQ12V

receiver link for example: nl.aliexpress.com/item/1005005207698624.html

I have the POE version and it won’t connect to the receiver. The remote control that came with the receiver will set it off though. Any ideas?

@michielcornelissen2430

Ай бұрын

The receiver needs to be compatible with and programmed for the Reolink. Might try the program the receiver again, also at other distances.

@jw9508

Ай бұрын

@@michielcornelissen2430 How would I do that? It’s just the button on the receiver correct?

@michielcornelissen2430

Ай бұрын

Yes, you need to put it in programmering mode

@eliset906

23 күн бұрын

This trick only works with the V1 of the chime/doorbell. Check the sticker on the chime to see what version you have. V1 works at 433Mhz, V2 was changed to 900Mhz.