Sorry, another long one but this isn't a quick process. That said, I think that I have found the cause of the problem!
Жүктеу.....
Пікірлер: 25
@sd8499 Жыл бұрын
Nice work, Nat! Hope you figured it out by now. And remember, there’s a Dutch saying: “ better go in a bit wonky, then missing ik straight “ 😂
@NatsNackersYard
Жыл бұрын
I am sure that there is some 'lost in translation' going on there!
@derekdingwall Жыл бұрын
Yes Nat theres something missing by the looks of things👍
@NatsNackersYard
Жыл бұрын
Definitely!
@grahamhider3754 Жыл бұрын
Brave man Nat ❤🔧🏍
@NatsNackersYard
Жыл бұрын
Or stupid!
@damiondavid536 Жыл бұрын
If I am reading the parts diagram correctly, a hex bolt, a lock washer and a stopper plate, hold the pin in the idler gear, which holds the idler gear inside the crankcase
@NatsNackersYard
Жыл бұрын
Yep. I appear to have two out of five!
@damiondavid536
Жыл бұрын
@@NatsNackersYard The lock washer and stopper plate look like they have been used on a few models, I put the part numbers into CMSNL to get a decent image of each part, they look easy enough to source used as well
@timparker9235 Жыл бұрын
fascinating watching you do that Nat - saw 40 minutes and thought it might drag but it flew by - nice!
@NatsNackersYard
Жыл бұрын
Thanks mate. The day was much longer!
@keithriley3159 Жыл бұрын
Screaming at the screen Pull the fcukin pin out 😂😂😂 That pin should be flush, passing thru the housing, gear and into the other side
@NatsNackersYard
Жыл бұрын
I tried but it didn't want to come out. A bit of a shove and I now have it flush!
@keithriley3159
Жыл бұрын
@@NatsNackersYard maybe not being installed properly has caused a burr on the pin and/or the engine case. At least it’s in now
@NatsNackersYard
Жыл бұрын
My thinking exactly
@callandy100 Жыл бұрын
Fascinating and well executed. I'm intrigued to see what is missing to hold the gear in place (sorry, my terminology is worse than yours!). Cheers, Andy.
@NatsNackersYard
Жыл бұрын
I have worked it out
@stephenwalsh8184 Жыл бұрын
🏍👍
@NatsNackersYard
Жыл бұрын
🏍️💪😜
@rickconstant6106 Жыл бұрын
I don't know that engine, but I find it hard to believe that the idler gear shaft is not supposed to pass through and be supported on the inside as well. I suspect a burr may have formed on the shaft, or the inner mounting point, as a result of the gear running out of line, and this is stopping the shaft either going fully home, or pulling out.
Пікірлер: 25
Nice work, Nat! Hope you figured it out by now. And remember, there’s a Dutch saying: “ better go in a bit wonky, then missing ik straight “ 😂
@NatsNackersYard
Жыл бұрын
I am sure that there is some 'lost in translation' going on there!
Yes Nat theres something missing by the looks of things👍
@NatsNackersYard
Жыл бұрын
Definitely!
Brave man Nat ❤🔧🏍
@NatsNackersYard
Жыл бұрын
Or stupid!
If I am reading the parts diagram correctly, a hex bolt, a lock washer and a stopper plate, hold the pin in the idler gear, which holds the idler gear inside the crankcase
@NatsNackersYard
Жыл бұрын
Yep. I appear to have two out of five!
@damiondavid536
Жыл бұрын
@@NatsNackersYard The lock washer and stopper plate look like they have been used on a few models, I put the part numbers into CMSNL to get a decent image of each part, they look easy enough to source used as well
fascinating watching you do that Nat - saw 40 minutes and thought it might drag but it flew by - nice!
@NatsNackersYard
Жыл бұрын
Thanks mate. The day was much longer!
Screaming at the screen Pull the fcukin pin out 😂😂😂 That pin should be flush, passing thru the housing, gear and into the other side
@NatsNackersYard
Жыл бұрын
I tried but it didn't want to come out. A bit of a shove and I now have it flush!
@keithriley3159
Жыл бұрын
@@NatsNackersYard maybe not being installed properly has caused a burr on the pin and/or the engine case. At least it’s in now
@NatsNackersYard
Жыл бұрын
My thinking exactly
Fascinating and well executed. I'm intrigued to see what is missing to hold the gear in place (sorry, my terminology is worse than yours!). Cheers, Andy.
@NatsNackersYard
Жыл бұрын
I have worked it out
🏍👍
@NatsNackersYard
Жыл бұрын
🏍️💪😜
I don't know that engine, but I find it hard to believe that the idler gear shaft is not supposed to pass through and be supported on the inside as well. I suspect a burr may have formed on the shaft, or the inner mounting point, as a result of the gear running out of line, and this is stopping the shaft either going fully home, or pulling out.
@NatsNackersYard
Жыл бұрын
I think that you are dead right mate.
👍
@NatsNackersYard
Жыл бұрын
🏍️💪
FIRST
@NatsNackersYard
Жыл бұрын
Back on top