Just had my starter tilt trim motor rebuilt for 84$ at a starter shop marina wanted 1400$ dollars to do it ! great video ! You watch these and it gives you the confidence to do it yourself ! Thanks

THANK YOU for posting this video! The trim on my motor was really struggling on the upper end and was getting progressively worse. After iterating through several YT vids, I found yours. Adding fluid fixed the issue. Note that I am NOT a mechanic -- your vid gives a great overview! I ordered parts on Amazon and had my trim/tilt issue fixed in

Great info here Captain. I appreciate the time and effort you have put into this clear and informative video. Thumbs up!

Thank you so much! I have a 90hp Yamaha on a pontoon boat. That did it... with the screwdriver! Dropped it down with ease. I will later try the hydraulic fluid part. Super video!

THANK YOU! Just just saved me a trip to the shop, a wad of cash and being without my boat till "my turn" came around to get it worked on. Mine is working with just some added fluid and bleeding.

dude you just saved our lives in the middle of the lake on a hot busy day. thumbs up.

@GadgetMan777

5 жыл бұрын

You filled it up in the middle of the lake?

Great tutorial Captain. The soap dispenser idea is brilliant!

Now I know you can fill/replace the fluid in the 50hp. Mine is a 2014 but looks the same. Enjoy your new boat, looks great.

Tanks for the many tips for Yamaha 50. I have an 1999 model. 👍 Jan

Excellent tutorial and “common sense approach” they don’t make them like that anymore “thumbs up”

Well done Cap !!! Thank you so much for sharing. Tight lines.

Thank you Captain for taking the time to post this. Saved me a lot of money and downtime for my boat.

@Cavanaugh68

5 жыл бұрын

Thank you for watching!

I appreciate your video. Good job Capt.

This was exactly what I was looking for. Thanks! Solid video!

Great video! Straight to the point!

thanks for the video, very helpful.

Just watched this video, very plain and informative! Thanks Captain!

@Cavanaugh68

7 ай бұрын

Very welcome

Thank you captain drew! Got stuck up! Added fluid and tapped! Worked!

@Cavanaugh68

Жыл бұрын

Excellent!

Awesome explanations thanks guy

Drew, if the relay is bad it won’t work period. So if the motor works but is struggling it’s the pump. Also, just put the trailer on ramps and lower the front so it’s level. It needs to be level to fill correctly. Just my suggestions. Glad you got it fixed though! Good luck

@redboyize

5 жыл бұрын

Adam Hartless hey I have a Evinrude xp 150 and my tilt won’t work not even make a sound so I manually lift the motor and I’m able to let it down if I put the green wire to a battery and ground the blue ..... any idea why it’s not working when I use the switch it has 2 switches one at the back of the boat and one on the throttle handle neither one works

@zash008

4 жыл бұрын

@@redboyize like relay or fuses

Flipping the trim wires on the relays is great when you only have one side not working. I like using a test light and checking the outputs on the relays, because it also rules out the switch being the culprit. My motor has both the throttle control trim switch, plus one on the side of the engine. To rule out both switches form the problem solving, I use a test light and check the relay outputs to see if the relay is putting out power. If you hear the click on the relay and the test light does not light up, you more than likely just found your problem, bad relays. For filling the trim pump, I found that the same filler kit for the seastar hydraulic steering systems have a great little hose and fluid bottle adapter for topping off a trim pump. Thanks for the hand soap container tip, not a bad idea. I had used an old rain-x container with the flip top nozzle for filling as well.

@stevenstocker2131

2 жыл бұрын

So I just put in a new relay and the motor will go down but not up. If I flip the wires then it will go up! So the relay is good. When the motor is up is slowly comes down. Could there me a fail safe button causing my relay to not go up?

Worked like a charm.

Thank for the helpful video

Great show and very well explained thank you very much from Sydney Australia

@Cavanaugh68

Жыл бұрын

Glad you enjoyed it

Thanks Captain. Going to have to try that on mine's.

Man! Thanks what a good video

Thanks for the info. I'm in Satellite Beach and just suffered the same thing with the same motor in the banana river. Hopefully it's just low fluid...

hi thanks its help more to me i want to ask if the green wire for the down can be also put on the negative terminal of the battery..thanks

Thanks for the detailed information, our brand new Yamaha has the trim stuck.

@Cavanaugh68

3 жыл бұрын

Glad it helped

Great video, helped me solve my problem

Great help - thanks!

I had a second person hold the trim motor up while I added fluid. It didn’t take very long to fill it up and began working within minutes

Great video

Great Video! Thank you very much!

@Cavanaugh68

3 жыл бұрын

Glad you liked it!

Great job, thank you

You are amazing thanks

Thank you for the video.

@Cavanaugh68

8 жыл бұрын

Thx

Thank You! This saved my bacon:) !!!!

Thank you!

My trim ran up for a few seconds than stopped. Won't move at all. You are saying the fluid is the issue for my problem? Is there a sensor that tells the trim motor not to run if fluid is low?

Question. I have just replaced by tilt motor on my Yamaha 40. Motor runs great, but nothing happens. I have fluid. I opened the hydraulic relief, lowered drive, and closed the relief. I checked the small coupler between the motor and the pump, I guess that could have come off. Anything else to try?

You need to have your transom perpendicular to the ground as best you can, lower your jack down as far as possible helps when adding fluid, the guy who replaced the motor you have to make sure you got the motor shaft connected back to the pump shaft, the motor is humming because the motor shaft is in a bind with the pump shaft or it's free to turn and running but not turning the pump shaft.

Great video! Quick question. What goes out in an electric-drive hydraulic motor that leaks fluid, or has not fluid in it? Does the motor just burn out, or is does something happen to the cylinder?

@jerry6613

5 жыл бұрын

my motor went out. i could tap the motor and it would kick in for a second or two. when i took the old motor off, some of the trim fluid that was under the motor came out. i replaced the motor and topped off the fluid and now i am all good.

Awesome. Thanks Cap.

Captain, do you know any good places to buy these replacement assy's?

Both of mine started acting up on my 2013 dual 200's. All I get is a clicking noise out of both solenoids. Will try this when I get home.

@Cavanaugh68

Жыл бұрын

Let us know if you got it fixed and what was the issues.

Thanks well explained

@Cavanaugh68

3 жыл бұрын

You're welcome

Yup! Always lightly strike the side of your electrical motors to make sure you don't crack those large magnets on the inside to make spots of random polarity or create permanent contact with the inner coil! 👍 guy knows his DC motors lmao

@Cavanaugh68

7 ай бұрын

Great point!

Nice job, thanks. So, my Yamaha 200 was on the trailer all winter, and when I took it out of the water months ago, the tilt was fine. But now, I hear the motor whining, but the motor won't move, and it's in the up position for trailering. Same thing, correct? Just try adding the fluid? Perhaps it's an obvious question/answer, but I want to check because I'm very non mechanical and the obvious sometimes isn't so obvious to me.

@Cavanaugh68

7 жыл бұрын

You can try to add fluid.

hello dirty switch by throttle can be opened and cleaned very easy job and low voltage can be a problem , I have lowrence and have a voltage display and low voltage alarm on my depth finder ,, good video .. I had my engine come out of water because switch got saltwater in it and I had to unplug it and use the motor trim to lower the engine

@Cavanaugh68

8 жыл бұрын

+boashna I use corrosion block on the switches. It helps prevent this.

Will any type of hydraulic fluid work or is there a certain kind recommended? Thx

No, no, no! That’s a great way to crush your hand when the engine comes down. If you blow a seal, you’ll crush your hand. At the very least you need to block the drive up so if you lose your fluid or the relay fuses (Burned contacts) it can’t continue down to crush your hand. Putting your hand in that position is stupid and dangerous.

Thank You ,Thank You

Just saved my life

Hey, just noted. If you positive the blue wire to a battery, and hope to get ground through the motor and bracket assembly it did not work in my test. I had to ground the green wire directly. Then to reverse polarity, to push the motor down, I went Green to positive, and Blue to negative.

@jimc108

3 жыл бұрын

I could not test my 2 wire new trim motor by grounding the trim motor to the engine block or directly to the battery. I had to do what you described. If you have a two wire trim motor and you want to test it power the blue and green leads.

could you hear air in the system when it was low? My yamaha trim just started doing this.

@Cavanaugh68

7 жыл бұрын

No. Mine I drained, realized it was no longer working. Then replaced it. The seals may be leaking in yours. They do sell rebuild kits. Sometimes cheaper and better to just replace it.

Fantastic! I tried this the first time, but didn’t do a good job of getting trapped air out. Knocking that cylinder a little and using the soap bottle with the hose from an old brake bleeding kit seems to have done the trick. Thanks for the tip!

@MrWhiteboi604

2 жыл бұрын

I knocked mine and the magnet inside came loose and started knocking back and fourth.

Do you happen to remember the fluid capacity in this unit? Couldn't find the info in my manual.

How do you replace the piston seal on this single piston PTT assembly, I was able to remove the cover nut (the one with the 4 holes that hold the seal) But I can not remove the piston or disassemble the interior of unit.

@Cavanaugh68

8 жыл бұрын

+Justin Joseph By calling your Yamaha Mechanic. That is beyond my scope of doing things. Too much involved there that needs to be precise.

Is that a SHO? Mine doesn't have an 18mm nut... I have a cap that unscrews (250 sho). I was told to raise it all the way up.... fill it.... then put the cap back on. Didn't fix my issue and mine is doing the same thing as yours. Sounds like it get very weak when almost max up.... or almost max down. Help!

@Cavanaugh68

6 жыл бұрын

No mine is the 115 LB

Where do you hook up your ground wire to??? Some where on the engine and the other end hooks up positive side of battery?

@justindavis1727

3 жыл бұрын

black ground on battery to bolt on engine, red on positive battery to green or blue on trim motor

Thank you!!!

@Cavanaugh68

Жыл бұрын

You're welcome!

I can't get my trim tab up/down dash instrument gauge to indicate. Changed gauge and I'm getting voltage but but no signal coming from engine. Any ideas what the problem?

@zash008

4 жыл бұрын

Signal coming from pink wire? I thing it indicates with ohms (resistance) doesnt it?

I have a tilt motor that is stuck in the up position. Constantly runs unless I press the downward button or turn the battery off . But it will not go down. Any ideas?

The trim motor will lift my 2014 fx250 Yamaha motor about 15% degrees , motor still will run but not lift engine any higher.we lifted the engine manually and set the pin to hold it up in order to add fluid hoping that was the issue. After unscrewing the #18 nut, fluid started leaking out so it’s apparently full of fluid?I could lover the motor now if I physically lifted the engine enough to disengage the pin, so the motor appears to be working so what now? Wesley

@Cavanaugh68

7 ай бұрын

Sounds like the pump itself has gone bad.

Mine clicks but doesn’t move. Gonna try this tmrw and see what happens

Why not use a Lower Unit refill pump - goes directly into the bottle of trim/tilt fluid and has a nice flex tube.

@brucewilliams2106

Жыл бұрын

cuz there's no air vent

Trim gauge not working on my boat.

Mine is stuck and won’t go up and I’m afraid to drive it to get it fixed what do I do

I just replaced the trim motor on my 150hp Yamaha. To do that I removed the hydrolic piston pin to tilt out the assembly to access the rear bolt. the motor humms but the piston won't go up or down now. What gives.

@michaelwhitley2569

4 жыл бұрын

What was your diagnoses ? Same problem here with 150

@JamesWhite-tg4kw

4 жыл бұрын

Sounds like it needs fluid

I am having the same issue on my Evinude 93 engine it doesn't wanna go up or down I added fluid to my Trim & Tilt and still won't go up or down.

@redboyize

5 жыл бұрын

Juan Dtrinidad I’m having the same problem did you find out the problem, mine won’t even make a sound no noise at all

The screw that's on the side of the trim and tilt that u can turn and manually pull up ur motor! Does that screw need to be tighten back up, before adding trim and tilt fluid?

@Cavanaugh68

Жыл бұрын

I am not sure, see if someone else can answer this

Captain C, my current position it all the way down and won’t tilt forward. Shows continuity on blue and green when switch is tried and getting 12.4 ( motor off ) Relay replaced but still clicks. Could it be as simple as fluid ?

@daveperson1722

10 ай бұрын

Also motor spins when I dismantled it off the mount

@Cavanaugh68

9 ай бұрын

Does not sound like fluid. try the fluid and see what happens.

So hook the blue wire to positive, then ground which wire ? Green or a different one ?

@Cavanaugh68

7 жыл бұрын

Not sure about that one. Maybe someone will chime in. I will say that the blue usually means up(sky) and green usually means down(grass)

@ASMR_sounds_for_kids

7 жыл бұрын

To go up run the blue cable to posits on battery but first add a second new wire too the negative on battery then connect that to the frame of the engine as a ground.

The motor switch works on my boat but the gear shift and bow switches don’t work. Any idea what could be going on?

@Cavanaugh68

5 жыл бұрын

Do you mean the switch on your engine itself works? But the throttle one does not?

@kenawtry5056

5 жыл бұрын

Yes. The motor switch works but not the gear shift or the bow switch

My motor is in the down position and I can not get it go up. I can hear it whining like it wants to move. You it just need trim oil

Never knew that little screw was on the side of the motor to lower it. Had I known, it would have saved me a ton of time on the water. Can't get home with the motor up. Thanks for the info.

I got a 1984 115 hp evinrude trim powers up fine then slowly goes down like you let off a hydraulic jack is it a seal or something else

@Cavanaugh68

4 жыл бұрын

Could be the bushings. Is it the original trim motor?

@samtate1260

4 жыл бұрын

Drew Cavanaugh yeah as far as I know I bought it in April then that pandemic hit Got a good deal because it was overheating on one side I put water pump and thermostats on it boat and motor 700 clean title on both trailer an boat

Hi my one will not go down what you think might be thanks

@Cavanaugh68

Жыл бұрын

Hard to say without more details.

My problem is the hydraulic lines the old ones are dry rote and leaking.

@Cavanaugh68

5 жыл бұрын

Replace them.

Will this fix leak down, mine slowly goes down?

@Cavanaugh68

5 жыл бұрын

No. If it is leaking most likely needs seals or to be replaced.

@peterhazelwood9325

2 жыл бұрын

If you cannot see evidence of oil leaking ,maybe the down screw is not tight and allowing it to leak down internally.

Take the blue wire, And ground out the green wire on the - of the battery. Its the direction of the current that makes the motor go left or right. Engine goes down: BLUE - GREEN + Engine goes up Green + Blue -

@risin-

3 жыл бұрын

you got the same thing for both..that can't be right

Thanks for the video.. ez-pz

How do you flush out the old fluid? Siphon??

@Cavanaugh68

5 жыл бұрын

Yes or drain plug.

@cyrusdavirus007

5 жыл бұрын

Drew Cavanaugh the Fluid in my trim is grey I don’t know what if it’s Yamaha hydraulic/power steering or DEX 2. Service manual calls for dex 2. I want to do a fluid exchange but I’m worried about using dex 2 and having a little bit of the power steering or whatever it is that is in there now. What do you think?

@Cavanaugh68

4 жыл бұрын

Just cal Yamaha Dealer and ask them. I am not sure.

@zash008

4 жыл бұрын

@@cyrusdavirus007 i took a snap shot of a document but cant find it now on my phone but i think i remember thats all that fluid is (Dex 2) half price at autozone or double for the yamaha labelled bottle

just park your boat on an incline bow down?

Is this 80hp 4 stroke

@Cavanaugh68

2 жыл бұрын

50 hp

Brushes stuck NOT bushings!

😊😊🎉😊😊😢

Did you ever find where fluid leaked out from? There should be evidence of a leak somewhere don't you think? Is changing fluid periodically a recommended maintanace?

@Cavanaugh68

8 жыл бұрын

+Stuart Kidder I do not think it was leaking, or much. Over the years just wear and tear causes so small of a leak that eventually you need to replace the fluid. If your motor is working and you have no issues with up or down or both, then you are fine.

@matthewable2975

19 күн бұрын

@@Cavanaugh68 Normally its a bad seal or seals that need to be replaced due to they are dry rotted.

Why not name every city and state ? In your introduction?

@Cavanaugh68

8 ай бұрын

I can do that. Thanks for the suggestion...

@Cavanaugh68

8 ай бұрын

Because where I guide at is east of Orlando near Cocoa Daytona and New Smyrna Beach. The Body of water that covers this 60 mile stretch is called the Mosquito Lagoon. I know the area but not every else does, so for a tourist you want to tell them where you are located near Disney. every one on earth knows Disney. From Orlando it is about 45 minutes to Daytona, Cocoa or New Smyrna. We as guides daily use each of these ramps in each of this cities. So some days I launch in Cocoa, the next day I may be fishing in Daytona. So it varies.