X-UAV Talon Pro Long Range Build
Ойын-сауық
Here's my build of the XUAV Talon Pro (aka Mini Talon V2). I have used some 3D printed parts for this build. I also opted to use a Pixhawk lite flight controller rather than a regular all-in-one FC like Matek Wing F405, as I intend to use this as a small mapper. Also, I have covered the entire plane with 3mil laminating film, and added two layers of 5mil laminating film for the belly of the fuselage to make it tough.
Specs of my build:
X-UAV Talon Pro 1350mm
Pixhawk lite flight controller
Ublox M8N GPS
MFD Nimbus x2814 510KV motor
Emax es09md servos for the Vtail
Hitec HS-5085mg for the wings
Runcam Phoenix nano Bardwell ed. FPV camera
Runcam HD
Caddx Turtle V2
3-way camera switcher
Digital airspeed sensor (i2c) with pitot tube
Matek 5in1 pdb
Hobbywing flyfun v5 40A esc
Aeronaut CAM carbon folding propeller 10x7
Matek 1.3ghz
Singularity RHCP sidefeed 1.3gHz antenna
Dragonlink nano rx with dragonlink antenna
mpx connectors
0.96" OLED
3D printed parts
6s2p 9600mAh 21700cell custom battery pack
6s3p 15000mAh 21700cell custom battery pack
AUW: 2260g
-------------
check out BUILD UPDATE on the talon pro :.
• X-UAV Talon Pro Long R...
-------------
***PLEASE LIKE AND SUBSCRIBE TO MY CHANNEL FOR MORE VIDEOS***
------------------------------
Reflexion by Props / propsmusic
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/3feOCNc
Music promoted by Audio Library • Reflexion - Props (No ...
------------------------------
Пікірлер: 57
Fantastic work bravo
A clever and streamlined build!
@windfpv
2 жыл бұрын
thanks mate!
as always, your work remains excellent.
@windfpv
3 жыл бұрын
Thanks mate!
sweet setup! The way you modified the nose has given me some good ideas on what to do with mine... I have glued mine and I am waiting for the servos and matek f405 fc to arrive
@windfpv
3 жыл бұрын
You may want to print a front skid if you have access to 3d printer, I have posted it on Thingiverse 👌
@giorgiontanas8618
3 жыл бұрын
@@windfpv thanks you so much for sharing the designs! yes I use a 3D printer for many of my rc builds, I will look you up on thingiverse!
@windfpv
3 жыл бұрын
Print the front and rear kids, the battery tray if you are using big packs, the wing spar support too.👌
You did an excellent job upgrading this plane. My students would like to do what you have done to get practice 3d printing and re-engineering.
@windfpv
Жыл бұрын
thanks for appreciating it! :-)
Very nice build :)
@windfpv
2 жыл бұрын
There's an update on this build, link on the description 😁
Nice master..ganda
@windfpv
3 жыл бұрын
Thanks boss
Nice I just got my Talon Pro in today
@windfpv
Жыл бұрын
Awesome!!!t
👏🏻👏🏻👏🏻👏🏻looks good. Now that I’ve seen all your videos and all your different planes, what’s your very best or favorite long range plane and why?
@windfpv
3 жыл бұрын
I haven't tried the new talon pro (V2) for long range yet. But a smoothened mini talon v1 is still my long range favorite, but maybe until I'm able to test the talon pro for long range flying. Hopefully within the month, of weather permits. My favorite mapping plane, on the other hand is the mfd crosswind mini, as this allows quick assembly/disassembly.
You have done a really good job with your Talon,I have the larger version and i can only hope my plane will be half as good as yours. All those 3d printed bit and pieces you should make a sell them they look great, if you ever do let me know i would pay for them and so would alot of other people.
@windfpv
Жыл бұрын
I also have the full-sized talon 😁 flies really well too. I use it for mapping jobs and for fpv flying. I have posted a couple of videos of the big talon in my channel 😁
@windfpv
Жыл бұрын
kzread.info/dash/bejne/npx2r6N7odLOj6g.html
Nice build! I like your Dragon Link Rx antenna arrangement which allows it to fold flat against the wing for transport packing. What li-ion 21700 brand do you use?
@windfpv
3 жыл бұрын
Panasonic ncr21700 4800mah
@joremontelibano352
3 жыл бұрын
@@windfpv thanks.
Awesome build mate. The cutout spaces for the VTX and RX in the wings look nice, did you use a foam cutter for that?
@windfpv
2 жыл бұрын
Just sharp blade and long nose pliers to pull the foam out
@tianzheng2570
2 жыл бұрын
@@windfpv Cheers!
Nice build. Could you please tell me where to find that airspeed sensor pitot tube mount?
@windfpv
2 жыл бұрын
I got it from Thingiverse, you have a lot of pitot tube mount to select from, which ever matches your pitot tube
Very clear and beautiful setup. How is your cg with 6s3p 21700 battery? My talon pro has pitching problem :(
@windfpv
Ай бұрын
Launches just fine. What's your power plant on your talon pro?
@wampelt
Ай бұрын
@@windfpv sunnysky x2820 v2 800kv motor, 9x6 propeller, 6s3p 21700 sony vtc6a batteries. İt flies very good. But has pitching problem at rth and cruise mode. But not pitching at angel, acro or manual mode
@windfpv
Ай бұрын
seems like you just need to redo the tune
Nice clean build. I just gotten mine and was wondering which nose to print. Can I have a link to the nose that you used on your plane?
@windfpv
3 жыл бұрын
I'll post the link asap
@windfpv
3 жыл бұрын
www.thingiverse.com/thing:4706516
@AreaKruzer
3 жыл бұрын
@@windfpv Thank you!
Did you thought of reinforcing the area under the wing where it connects with fuselage as it's just foam. I took a flight with this craft.. it flew beautifully. But after few hard turns the wing seperated from the fuselage in the air and whole thing just came crashing to the ground.
@windfpv
3 жыл бұрын
I have been thinking about that too..perhaps a piece of balsa would do.
@RaviSingh-wk7qk
3 жыл бұрын
I suppose.. but the curvy design of this craft makes it difficult. Talon and mini talon are very well reinforced. But they somehow did not do it in this model.
@windfpv
3 жыл бұрын
I have made a simple spar reinforcement, meant to be glued on the side of the fuse that joins the wing root. It provides more support. Apparently, it's for preventive action. In the case of your talon, this might not help though..but still you may want to check it out. I'll post it on Thingiverse.
@RaviSingh-wk7qk
3 жыл бұрын
Okay... Can you please share the link of thingiverse ?
@windfpv
3 жыл бұрын
@@RaviSingh-wk7qk www.thingiverse.com/thing:4867590
Hi can you post a link for the rear stabiliser 3d printed skid. I can't seem to find it
@windfpv
2 жыл бұрын
I'll get back to you with the file 😁
@windfpv
2 жыл бұрын
www.thingiverse.com/thing:4671891
hi, where can i get airspeed mount stl ? Thank you
@windfpv
Жыл бұрын
this one: www.thingiverse.com/thing:739578
@levik91111
Жыл бұрын
@@windfpv thank you!
brod san ka nag purchase ng 21700 cells mo?
@windfpv
3 жыл бұрын
May supplier ako dito boss, ncr21700 4800mah
@nickrcph3284
3 жыл бұрын
@@windfpv wow! guaranteed bang legit yan?
@windfpv
3 жыл бұрын
@@nickrcph3284 true rated naman na 4800mah yung cells
@nickrcph3284
3 жыл бұрын
@@windfpv nagbebenta ka ba?
@windfpv
3 жыл бұрын
Meron ako dito ilang piraso pa, pwede ko iassemble yung pack using my spot welding machine. San ba location mo?