Пікірлер

• 
  @CityVlogs673 күн бұрын

  Great editing 👌

• 
  @windfpv3 күн бұрын

  Much appreciated ☺️

• 
  @nguyenvanhai77287 күн бұрын

  Very nice. A vectored bellysiter VTOL is so much cooler that a tailsitter VTOL. Likely easier to control on decent too. Look forward to seeing more detail of this project as able to share.

• 
  @ErichFGS8 күн бұрын

  Love ur edition, nice flight!

• 
  @windfpv6 күн бұрын

  Thanks a lot!

• 
  @minirccreators35168 күн бұрын

  saraaaap

• 
  @rkelley847515 күн бұрын

  Just bought mine 5/20/24 and it has the old heatsink

• 
  @windfpv15 күн бұрын

  And does it overheat or not? Mine didn't come with shorter heatsink but didn't have any issues on overheating. Tested under 49C summer temperature here, didn't have any issues.

• 
  @meareAaron16 күн бұрын

  epic vtol build! would love to see more info on the wiring and internals for this build

• 
  @windfpv10 күн бұрын

  Thanks! Will do!

• 
  @wampelt18 күн бұрын

  Very clear and beautiful setup. How is your cg with 6s3p 21700 battery? My talon pro has pitching problem :(

• 
  @windfpv15 күн бұрын

  Launches just fine. What's your power plant on your talon pro?

• 
  @wampelt15 күн бұрын

  @@windfpv sunnysky x2820 v2 800kv motor, 9x6 propeller, 6s3p 21700 sony vtc6a batteries. İt flies very good. But has pitching problem at rth and cruise mode. But not pitching at angel, acro or manual mode

• 
  @windfpv14 күн бұрын

  seems like you just need to redo the tune

• 
  @AngelFernandez-je4uz19 күн бұрын

  Felicidades por la construcción y por el vuelo!!! Puedes compartir la configuración de Ardupilot???

• 
  @krishverma227020 күн бұрын

  if I want to add tilt function to rate motor is there any way to do that ?

• 
  @windfpv15 күн бұрын

  Yes, you define on the parameters which of those motors tilt

• 
  @krishverma227014 күн бұрын

  @@windfpv can you specify the perimeter .. as after the tilt the rear motor will provide thrust in backward direction to reduce the speed of drone while transpiration between flight modes. please 🥲

• 
  @krishverma227012 күн бұрын

  @@windfpv can you specify the perimeter cause it will give thrust in negative direction to decrease the drone momentum ... will it work that way

• 
  @windfpv10 күн бұрын

  actually during the back transition from fixed wing to VTOL, it should be able to cut the speed/momentum when the tilt motors move from horizontal to transition angle. No need to put a negative thrust on it. That would only make the system a lot more complex which isnt necessary

• 
  @krishverma22709 күн бұрын

  @@windfpv i got it but i have this project task to complete so actually need to make it work that way .. that's why i really need help !

• 
  @bradyboy12322 күн бұрын

  Yeeeew!

• 
  @Urko7622 күн бұрын

  Nice job!!!

• 
  @beefybeef132622 күн бұрын

  Just brilliant!

• 
  @minirccreators351622 күн бұрын

  wow galing

• 
  @GhostRyderFPV22 күн бұрын

  It _Is_ real, And it is _Really Heavy_ and _Finnicky as Hell!_ lol Want EIS? You can only use 2.7k VTx recording, Want to record in anything above 1080p on the VTx? You're limited to Standard Frame Rate sent to the VRx. Just weird stuff, man.

• 
  @TA-td9gd24 күн бұрын

  In your description you wrote you can add the Bluetooth Module to Taranis QX 7 board (should be true ..other videos showing this also ) .. do you know if this is also working on Taranis QX 7 Access ? (I flashed my R9M on Taranis QX 7 Access with ELRS and had a BT Module over S.Port working well ) but now I need to find a other solution to get the Telemetry Viwer App connected.

• 
  @windfpv24 күн бұрын

  Qx7s access already got built-in BT as far as I recall. im not sure if there's a spare uart on the Qx7s radio. but should there be one, then you can add an external bt module

• 
  @TA-td9gd24 күн бұрын

  @@windfpv I got the QX 7 Access (without the S) so I have no BT Module inside and no UART .. never saw anyone tried it with QX 7 Access but many ppl in forums had asking to that (incl myself) :-) thx anyway

• 
  @Migueldeservantes26 күн бұрын

  Thank you very much... this is way better than anything else I have seen.

• 
  @donjohnson774628 күн бұрын

  Do you have a the same video for inav 7.0.1

• 
  @donjohnson7746Ай бұрын

  The best vid of on this I've found so far, thank you for the detailed walkthrough.

• 
  @windfpvАй бұрын

  Glad it was helpful!

• 
  @nguyenvanhai7728Ай бұрын

  Chào bạn mình đã cài đặt giống như bạn mà mấy bay của mình vẫn khokng cất cánh được bạn có video lào chi tiết hơn cho mình sin để mình hoàn thành chiếc máy bay của mình mình sin cảm ơn

• 
  @windfpvАй бұрын

  can you provide some details? what mode are you trying to do the take off?

• 
  @DFEUERMANАй бұрын

  (5:29) Can data on serial monitor be decoded in arduino?

• 
  @windfpvАй бұрын

  Possibly if there's a proper CRSF translator

• 
  @JBWhiteАй бұрын

  Noob here with Goggles X and an Avatar HD Pro Kit (dual antenna)... what antennas (if any) do you recommend for both the VTX and/or the Goggles? Thank you!

• 
  @windfpvАй бұрын

  Vtx antenna are not that bad. What you would want to replace are those on the goggles. Put a good patch on it (e.g. truerc x-air/x2-air/x-ray), and some good omnis on the top ports (e.g. truerc singularity, lumenier axii2 long)

• 
  @cacador2009Ай бұрын

  friend, can you help me? My assembly looked similar to this video and I don't know what to do m.kzread.info/dash/bejne/k2mJtcWBeKXVd7Q.html&pp=ygUUVDEgcmFuZ2VyIHZ0b2wgYnVpbGQ%3D

• 
  @rccosplay3249Ай бұрын

  I thought the improved version of the Walksnail goggles X is coming out in August 2024???

• 
  @windfpvАй бұрын

  Yes the major upgrade still to come out by August yet. That's promised to have newer rf board.

• 
  @beyondfossilАй бұрын

  I recently purchased a Walksnail Moonlight kit but I only have 1080p60 as maximum in VTX REC. I guess I need to do my first firmware update but I'm surprised it doesn't come stock out of the box with 2.7k and 4k options.

• 
  @windfpvАй бұрын

  You need to setup the goggles to use standard instead of high bitrates

• 
  @beyondfossilАй бұрын

  @@windfpv Thanks for the quick reply. I have checked the bitrate is standard but still don't have 4k VTX REC options. I think another problem is my Fatshark Recon HD goggle's firmware is really old at 29.33.12 and the latest is showing 37.42.7

• 
  @windfpvАй бұрын

  @@beyondfossil hmmm, perhaps try updating goggles first to newer fw :).

• 
  @mateuszpachulski6211Ай бұрын

  @@windfpv it is not bitrate, it can be set to high, you need to set the frame rate to standard instead

• 
  @windfpvАй бұрын

  @@mateuszpachulski6211 oh right, thanks for the correction 💪

• 
  @tubamanandy2Ай бұрын

  Thank you - SUPER useful

• 
  @windfpvАй бұрын

  Glad it was helpful!

• 
  @istaykede1340Ай бұрын

  Thanks for everything. What is the wing type of the drone?

• 
  @Bill-NMАй бұрын

  Is trhe EIS "real time"? Do you see a stabilized image in the goggles while flying? I have a friend who gets nauseated using FPV with a non-gimbal-stabilized camera, and I'm wondering if this might be a solution.

• 
  @windfpvАй бұрын

  No...

• 
  @endremurtiАй бұрын

  Is it can be applied to pixhawk fc?

• 
  @windfpvАй бұрын

  You can

• 
  @LordFpv2 ай бұрын

  Yes,i need this...where i can download this font?THANKS

• 
  @windfpv2 ай бұрын

  gyroflow.xyz/

• 
  @LordFpv2 ай бұрын

  @@windfpv I need font,not gyroflow :)

• 
  @windfpv2 ай бұрын

  sites.google.com/view/sneaky-fpv/home It's under the Walksnail Moonlight folder :)

• 
  @endliberalism43052 ай бұрын

  Quick question bro. I hooked up a 5v system completely separate from the FC, strangely enough it feeds power back to the FC through the wing plugs …. It seems the manufacturer has some sort of power loop running through the wing and back to the LED plug. Have you looked into this issue ?

• 
  @windfpv2 ай бұрын

  Hmmm...im not really sure about how that flight controller is wired up, I'm actually using a different FC, basically everything on mine was DIY as I bought a t1 kit and converted it to VTOL. So I am using a different hardware...

• 
  @endliberalism43052 ай бұрын

  @@windfpv thank you

• 
  @redsharkss2 ай бұрын

  Do I need to use inverter module from Radiomaster t16s external UART? can you please share the like to inverter module

• 
  @yashass44052 ай бұрын

  i have only two rotors can i still use the same code if yes what changes should i make?

• 
  @stevietee102 ай бұрын

  OSDx_TXT_RES = 3 and placing elements on 60x22 works well also, gives a neat less crowded screen 👍

• 
  @windfpv2 ай бұрын

  Yeah, that would work on DJI wtfos. :) but It won't work with Walksnail, as it natively uses 53x20

• 
  @stevietee102 ай бұрын

  @@windfpv Yes, my apologies, I got that wrong 🤦‍♂

• 
  @patricehonvault26122 ай бұрын

  great, this is exactly the video I needed, thank you 😊

• 
  @windfpv2 ай бұрын

  Glad it was helpful!

• 
  @steinne2 ай бұрын

  excellent tutorial.... thank you!

• 
  @windfpv2 ай бұрын

  You are welcome!

• 
  @rscarawa2 ай бұрын

  Any good instructions on how to get these files put in the proper place on the X 20? I took a stab at it and my X 20 goes into emergency mode after a few minutes of running and also it gets stuck in a loop where it just keeps repeating the same thing over and over, any help would be appreciated

• 
  @windfpv2 ай бұрын

  You need to disable the Lua title (in the Lua page config)

• 
  @rscarawa2 ай бұрын

  Is that a file in need to update or a switch I can throw from within Ethos? I see the Lua menu where I can select the telemetry to display but nothing regarding title. Thank you for the help

• 
  @rscarawa2 ай бұрын

  I found the setting where you can disable the title. The only problem was it was already disabled and it’s still saying Yaapu Telemetry Ready, every second.

• 
  @windfpv2 ай бұрын

  Try the latest version of yaapu script for Ethos

• 
  @rscarawa2 ай бұрын

  Big improvement. Looping stopped. Any way to show airspeed instead of gps speed? Does the altitude zero out for the take off alt? Thx

• 
  @kielalcantara92332 ай бұрын

  Mag kano kaya ganitong setup 🤔

• 
  @windfpv2 ай бұрын

  invest about 30k excluding radio and FPV. Shipping cost for such big boxed model planes is insane!!!! :(

• 
  @lightningfpv90122 ай бұрын

  OSD still flickering?, and how can you do the GPS cords in that format on ardupilot?

• 
  @windfpv2 ай бұрын

  Yes, when vtx is recording I still find some flickering. But it is way better than before. If I don't record on vtx then OSD doesn't flicker (almost) unless it is flying on the lowest bitrate already/limit of range. Gps format can be changed thru parameters

• 
  @lightningfpv90122 ай бұрын

  @@windfpv which params, please

• 
  @g36pilot922 ай бұрын

  That Nano camera performs well!

• 
  @windfpv2 ай бұрын

  yeah :D

• 
  @schwarzflieger2 ай бұрын

  what's the max distance with goggle x?

• 
  @windfpv2 ай бұрын

  I have tried 22km, my max yet. Pretty sure it can do more

• 
  @bivirs652 ай бұрын

  22 km analog?@@windfpv

• 
  @windfpv2 ай бұрын

  Goggles X + Walksnail vtx, so digital not analog

• 
  @arnolddelosangeles26762 ай бұрын

  Good job

• 
  @zawisza__czarny2 ай бұрын

  NICE

• 
  @windfpv2 ай бұрын

  thanks!

• 
  @pilotlawaran2 ай бұрын

  jumper t pro can connected to this bluetooth module?

• 
  @windfpv2 ай бұрын

  I'm not sure if jumper T pro has uart port for the bluetooth module..

• 
  @kwaaaa2 ай бұрын

  Wow its been a while since I ran my walksnail, that looks excellent with all the OSD telemetry. What settings are you using on your walksnail? Looks like 25 Mbps looks solid

• 
  @windfpv2 ай бұрын

  That's 1080p, 25mbps. I recorded both on VTX and goggles,, but I overlayed the OSD on the vtx recording instead 😊

• 
  @JDDupuy2 ай бұрын

  Enjoyed the flight. Cool music track! I have 2 Crosswinds!

• 
  @windfpv2 ай бұрын

  Thanks buddy

• 
  @mgrxerx2 ай бұрын

  Can you share stl camera mount with pan and titl?

• 
  @asswift6773 ай бұрын

  Can it be used with inav or betaflight?

• 
  @windfpv3 ай бұрын

  i think so, as long as radio fetches gps telemetry

• 
  @I77AGIC3 ай бұрын

  definitely wouldn't cut off part of your heat sink since overheating has been an issue. also wtf is up with the fast forwarding??? how can anyone read what it says??? why???

• 
  @windfpv3 ай бұрын

  Nope, no issues on my goggles even with the stock Tin heat spreader, even before I installed the big heatsink. The reduced heatsink also went well, tested under 37C outdoors without overheating on Led1 and Led2, summer here goes 40C, peaks at 42 to 43C sometimes, i am confident it will hold perfectly.

• 
  @zawisza__czarny3 ай бұрын

  NICE