thanks again I wired same on my Yamaha R1 work perfect I love it very good video 👌 Cheers Bro 🍻

@wyzedefr6549

8 жыл бұрын

No problem at all! glad I was able to help. Ride Safe.

Hello friend!, THX for your video, I have this controller in my Hyundai Accent 2015, but works just when I have the lights of the car off if I turn my lights (at night) on doesn't flash. How can I solve this?. Thx!

+Richard H. Ruiz don't use the red from the "in" side, instead use the blue as (+). In the "out" side, connect both black wires as one and connect that to the (-) on the lights.

@noyb9284

2 жыл бұрын

So the red wire on the unit does NOT go to the yellow bike wire? Please clarify if the video instructions are not to be followed as I'm a new bike owner

I bought the same GS-100A module as you, where would I need to connect it if I want the flashing to happen when I press the front brake lever as well as the foot lever? Any info will do, thanks!

@wyzedefr6549

8 жыл бұрын

If you have access to a multimeter, test which wire will give you 12v when you apply the front and rear brakes. In my case, the wire that was giving 12v was the "Yellow" wire. So Red (module) to Yellow (motorcycle), Black (module) to Black (motorcycle). Hope this helps you out.

thanks

Question ❓ so as long as your holding the brake it will continue the pattern ❓

I bought a strobe controller lights mod. GS-100A 1307, but This model has three wires, red, black and blue, the problem is that I can not install because i do not understand where I connect the blue wire.

@DrAlmurshidy

4 жыл бұрын

Were you able to figure it out?

hello I bought that same strobe but it only works with half up switch. when the car engine it does not work will be league that came defective ??

@wyzedefr6549

7 жыл бұрын

I think it maybe defective if it only works with the switch half way up.

Hello, i need only the GS-100A Box?? or i need the another box with blue light? thanks!!

@wyzedefr6549

8 жыл бұрын

+Gonzalo Zambra just the GS-100A.

@gonzalozambraable

8 жыл бұрын

Excelent! Thanks, great Video! Very helpful

@wyzedefr6549

8 жыл бұрын

No problem, good luck.

What does blinker and brake look like at the same time? I am installing this on a integrated tail light as well.

@wyzedefr6549

8 жыл бұрын

the amber will shine through the "brighter" red braking status light, while pulsing.

@WatchThisPlay

8 жыл бұрын

Thanks man.

@wyzedefr6549

8 жыл бұрын

No problem. The pulsing really helps get the attention of drivers or other bikes behind you.

@cornycor

7 жыл бұрын

Nice video, thanks. Does the unit have a g-force sensor, so the lights only flash when braking at full force? Or does the light flash every time you hit the brakes?

@wyzedefr6549

7 жыл бұрын

Only when brakes are applied.

i bought a cheap universal ebay intergrated taillight didnt come with instructions or lables i want to put it on my 91 gsxr 750 i got all lights working but signals stay solid and wont blink any ideas ?

@wyzedefr6549

7 жыл бұрын

If its not blinking, i'm guessing it could be a relay instead of the light. To test this, I would connect it to a circuit testers and turn on the signal. If the tester is blinking, then you know it's related to the relay instead of your ebay purchase. If you don't have a circuit tester, you can also use a multimeter.

@randyhobson6343

7 жыл бұрын

WyZedEf R6 thank you for the fast response

@wyzedefr6549

7 жыл бұрын

You are welcome. Also another note is to make sure you install the resistor that are usually provided with the integrated taillights.

is this same set up wiring on 06 yamaha R1 Integrated tailight? where can u buy the Module?

@wyzedefr6549

8 жыл бұрын

yes, the connection should be the same for an R1. You can buy this on ebay, the link is in my description.

What if mine don’t ground out?

@wyzedefr6549

6 жыл бұрын

That_lowered_Accord _ the existing brakes should have a negative (black). If not, try connecting to bike frame.

you should wire the LED signal with resistor hyper flash makes you look like a noob :)

@wyzedefr6549

8 жыл бұрын

I totally agree. I've installed a flasher relay since this video. Thanks for the good pointer for others viewing this though!

@cipher978

8 жыл бұрын

+WyZedEf R6 nice. Thanks for the video I'll be installing mine and I have got some good points from your video

Wait so after explaining all of that you didn't show us what the strobes look like on.........smh

@wyzedefr6549

7 жыл бұрын

2:05 is how strobe looks like. 4 quick pulse, followed by 4 slower pulse.

@AlvlUpSavedMyLife

4 жыл бұрын

Lol.... uhhhh watch the video fool