Worst Engines of All Time: Ford Y Block V8

Автокөліктер мен көлік құралдары

Learn more about the Ford Y block engine used from 1954-64 and what issues it had. Unfortunately, it had a tough task to fill the flathead's shoes as its replacement, and despite having more power, it wasn't quite up to the task.

Пікірлер: 1 400

  • @m.j.mateyka7350
    @m.j.mateyka73502 жыл бұрын

    My dad was a mechanic in the 30's to the 60's. He had his own shop, so when I was 10 or so I started going over and helping him. (Child labor.) Just about every engine that came in had oil problems, because of the lack of oil changes, non-detergent oils, and lack of oil filters. My dad tried to convince people to change their oil more often, but few listened to him. (Remember the Fram ads that had "Pay me now or pay me later."?) One of my jobs was disassembling rocker arm assemblies, cleaning them and laying them out for my dad to put back together and put back on the car. Some times the entire rocker arm cover would be full of sludge. I would have to use a putty knives to get most of it off just to get to the bolts. He worked on a lot of Chevys (because there were a lot of Chevys), and they were as bad as the Fords. By the way, I change my oil and filters at 3,000 mile, because I was so traumatized by the image of those rocker arms.

  • @muffs55mercury61

    @muffs55mercury61

    2 жыл бұрын

    Great memories.

  • @m.j.mateyka7350

    @m.j.mateyka7350

    2 жыл бұрын

    @@muffs55mercury61 My dad's friend had a '55 Merc Montclair with a white top and the "Sun Glaze" bottom. We called it the Creamsicle. There were also Biltmore Blue and Springdale Green ones in town at the time. The pastels era for cars.

  • @otm646

    @otm646

    2 жыл бұрын

    I slapped heads on a sludgy (but not putty knife sludgy) mid '70s small block Chevy that'd sat since the early '80s. Owner switched to a modern synthetic oil. Car came back to me 6 months and maybe 4,000 miles later for a defective rocker arm. I'm telling you those rocker covers were spotless. That modern oil cleaned up that motor like a hot tank.

  • @cammontreuil7509

    @cammontreuil7509

    2 жыл бұрын

    Best comment on here. That old grade of oils was not that good.

  • @MarkBlackburnWPG

    @MarkBlackburnWPG

    2 жыл бұрын

    @@cammontreuil7509 Agreed -- "best comment" on here. Really, is there anything better than people who know what they're talking about? Rhetorical question. Thanks to Donald Johnson, and M.J. Mateyka for eliciting the great, anecdotal comments here.

  • @FlaWebmaster
    @FlaWebmaster Жыл бұрын

    I have been a Ford guy for over 60 years. Calling the Y-Block the worst engine of all time is an exaggeration. They had their problems, but they weren't that bad. As far as bad oil is concerned, that wasn't a Y-Block only issue. Sure the rear seals leaked and the rocker shafts wore out. I disassembled many a Chevy small block that had 3 inches of sludge in the lifter valley. Some early Chevy V8s didn't even have oil filters. My first hot rod experience was with Y-Block engines. In the mid sixties, they were cheap and plentiful. A Y-Block engine with a manual transmission would fry the tires to the ground. Back then, you could buy a decent car for $200. In the today's times, the Y-block seems prehistoric. Back then they were pretty cool.

  • @stout7668

    @stout7668

    3 ай бұрын

    It’s all on opinion. The Chevy engines were even worse

  • @walterhammond290

    @walterhammond290

    3 ай бұрын

    Check out the Dearborn Marine interceptor V8 from the 50s and 60s. Other than the bad transmission installed on the first generation of Marine engines, they were excellent. Very powerful and reliable. The y-block Ford had its problems but overall was an excellent engine.

  • @misterhipster9509

    @misterhipster9509

    2 ай бұрын

    Y-blocks held up well due to the fact they didn't make a lot power.

  • @133dave133
    @133dave1332 жыл бұрын

    We have two 1959 F-600 wheat trucks with 292's. We still haul wheat every year with them. We've owned these trucks for about thirty years now. I'm not a big fan of Y blocks, but they have been durable engines for us. Excellent maintenance, and not over revving, this is why I think that we have had such good luck. These 292's love being lugged around the farm hauling wheat, but once you get on the highway, everything is out the window. Ford, was asking a lot by putting these small engines in these trucks, but they do surprisingly well paired with super low axle gearing. Life was slower and happier back then, even the trucks.

  • @jimmy_olds

    @jimmy_olds

    2 жыл бұрын

    Not a farmer but used to sell grain body trucks, so I truly appreciate your comment:) your last sentence is spot on, I have a 67 C10 with 3 on the tree (w/un synchronized 1st gear), 250 inline 6, and at least a 4 something rear gear. Her happy speed is 45mph, like you said, life was slower and happier back then.

  • @paisleyprince5280

    @paisleyprince5280

    2 жыл бұрын

    @@jimmy_olds We still have a c20 with a 292, 4 speed, and almost asinine deep gears. It likes 50 mph lol

  • @1SqueakyWheel

    @1SqueakyWheel

    2 жыл бұрын

    It really was happier, I think! When I was little, my dad had a 64 or 65 (I can't remember which) C60 dump truck. A big hulking truck with a little 292 straight six in it, a 4 speed and a gigantic split differential. It would pull anything, but it wouldn't do it fast. It was slow in the highway, but hey.. it was a dump truck. It suited him just fine, and I loved riding shotgun with him in it. Great memories! He let that old Chevy sit unused for many years, eventually selling it to somebody else who only wanted the dual linear ram dumper off of it. I sure wish we still had that dumper to put on our LWB 7.3 F550... It would dump a lot more weight than the scissor dump we currently have on its 16 ft bed.

  • @133dave133

    @133dave133

    2 жыл бұрын

    @@1SqueakyWheel Both our trucks have the telescoping dual ram setup. It's amazing how strong those hydraulics are. We just have to make sure that we are not on a side hill is all. Three pumps on the vacuum assisted brakes, and they will stop on a dime loaded.

  • @1SqueakyWheel

    @1SqueakyWheel

    2 жыл бұрын

    @@133dave133 Yeah that's just common dumptruck policy. The real dumptrucks, capable of dumping 18 or more tons, are very careful when it comes to lateral listing across an incline.... bad juju for sure! The problem with the cantilever dumper on our 01 16' f550 is that it's a conversion for a truck of that class, but only an 8 to 10 foot bed at max. We bought it already converted, as it was one of the three biggest selling points. Tips great when fully loaded with wood or scrap metal, but it can't handle the density of a 6-8 ton load of crushed rock that the truck is otherwise fully capable of hauling. Gotta shovel half the load out by hand before letting the tipper do the rest. Really makes us miss that slow old Chevy, or at least her dumper. And you're right, our chevy had a 2-stage duo also. We weren't capable of overloading that old truck! Both the c60 and f550 have/had wooden stakebed sides, btw, as I'm assuming yours do too.

  • @midnightgambler3718
    @midnightgambler37182 жыл бұрын

    According to my dad, these motors weren't *that* bad. They needed maintenance and fresh oil on time, but they were never designed for racing without modifications. He had 3 1957 Fords that he enjoyed and used for years

  • @67marlins

    @67marlins

    2 жыл бұрын

    Midnight- Your Dad was right. The Y block was kind of on-the-edge of "treat it right, and you'll be fine".

  • @mchl8

    @mchl8

    2 жыл бұрын

    That's why it was no good

  • @larryhutchens7593

    @larryhutchens7593

    2 жыл бұрын

    I was working on cars back then. Saw a lot of those Y blocks with the add on rocker shaft oiler systems installed. They had a good basic engine design, Y block & forged crank but failed with the little stuff. The over/ under intake ports were a bad idea.

  • @wallbanger3

    @wallbanger3

    2 жыл бұрын

    I worked on those , the big problem was the intake seal it was a long seal The sealing tech wasn’t good with cork gaskets Right Stuff fixes them it’s a new sealing agent

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@mchl8 If you groove the center camshaft journal, or replace it with a later one that was made with a groove, it was fine. Easy fix.

  • @michaelnault5905
    @michaelnault59052 жыл бұрын

    Those Y blocks IMO get an undeserved bad rep. A very long time ago I drove small commercial trucks that were 30 years old at that time. They were powered by 292cid Y blocks. Those trucks gave daily commercial service for decades with enough miles on them to roll the odometers into infinity. They delivered adaquate power reliably for a very long time. They were serviced by a knowledgeable old school mechanic, but their longevity, and endurance were IMO remarkable.

  • @mark_osborne

    @mark_osborne

    2 жыл бұрын

    Very interesting Michael

  • @flight2k5

    @flight2k5

    2 жыл бұрын

    I mean they rolled at 99999 so I’m sure it didn’t have that many miles

  • @1965l88

    @1965l88

    2 жыл бұрын

    @@flight2k5 That's no gauge of how many miles they might have had on them. As far as you or I know, the odometer could have rolled completely over several times. With that said, I've had pretty much the same sort of experience with the 292 Y blocks as Michael. They're among the sturdiest, most reliable workhorse engines I've been around. And, they could actually be made to perform pretty well if one knew what he was doing.

  • @flight2k5

    @flight2k5

    2 жыл бұрын

    @@1965l88 naw it’s an American made engine from the 60s. It didn’t do it multiple times 🤣

  • @jamesfrench7299

    @jamesfrench7299

    2 жыл бұрын

    @@flight2k5 lol stop it! They had just developed a slew of new engines with 1950s technology. They got better over time.

  • @timothybyrom5560
    @timothybyrom55602 жыл бұрын

    In with the crowd on this one. Good oil was the secret. A Y block with a PCV valve would thrive in today's world. They weren't a powerhouse, but they were comfortable torquey little fellas that if you did your part would last a very long time.

  • @jamesfrench7299

    @jamesfrench7299

    2 жыл бұрын

    Good towing engine?

  • @timothybyrom5560

    @timothybyrom5560

    2 жыл бұрын

    @@jamesfrench7299 Yeah, little slow by today's standards.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@timothybyrom5560 Actually, the 56 - 57 Y-block was pretty potent. Then in succeeding years, they kept detuning it, until in 1962 cars, the 292 only made 170 horsepower, (the 57 292 made 212 horsepower).

  • @timothybyrom5560

    @timothybyrom5560

    2 жыл бұрын

    @@michaelbenardo5695 Thanks for the info. I'm not really an expert. I just know the experience I've had with some of the old trucks. When I was a kid a friend of my dad had an old one ton that he hauled logs,and firewood with. She wasn't the fastest thing around, but it would get it done reliably every time.

  • @dougpersell8776

    @dougpersell8776

    2 жыл бұрын

    @@jamesfrench7299 I loaded my f600 with scrap iron and pulled a trailer hauling my skid steer behind it. It did a great job i was very impressed i should have rebuilt it but replacing it at the time got me going agin. A older guy i know has a 50s f800 semi with a 292. For what it is size wise and time line it is a good towing engine. I am not a ford guy but when ford went from the flat head to the Y block they did great job a big step forward .

  • @bobmeyer7009
    @bobmeyer70092 жыл бұрын

    Interesting. Back in the day I had a 312 Y-block, bored .060" over with high compression pistons, an Isky cam, flamethrower ignition, 4 barrel carb and headers - it propelled my '57 stick shift Ford quite nicely, and with no oiling problems at all. Careful assembly and the proper oil is all it took.

  • @TKing-ph7bq

    @TKing-ph7bq

    Жыл бұрын

    I have had several 312's and like you I believe they are tough and dependable. I think the bad rap was because of people never changing oil or doing any kind of maintenance. If they were so bad why were they prized finds for engine swaps back in the day?

  • @wyo1446
    @wyo14462 жыл бұрын

    I grew up around Y-Blocks, these motors were bullet proof, and much stouter than Chevrolet's small block at the time. Just change the oil like you're supposed to. The 57 Ford 312 was one of the fastest cars on the road, dominating NASCAR that year. I have a 56 F100 with a built 292, with all the modern upgrades, it rolls along with today's traffic with no problem.

  • @antoniohosino145

    @antoniohosino145

    9 ай бұрын

    THE OIL GALLYS ARE ONLY SO BIG , SLUDGE BUILD UP RESTRICTS OIL FLOW & LUBRICATION EVENTUALLY CAUSING ENGINE FAILURE , TOP END TICKING , KNOCKING LOWER END , CLEAN OIL & FILTERS A MUST !!!

  • @antoniohosino145

    @antoniohosino145

    9 ай бұрын

    FROM A ENGINE STANDARD FORD COULD HAVE MADE IMPROVEMENTS ALONG THE 10 - YEAR RUN , ANY LOGICAL MACHINE SHOP WORK TO IMPROVE LUBRICATION AND PERFORMANCE IS WORLDS APART FROM A PRODUCTION LINE ENGINE ASSEMBLY !!!! AT EXTRA COST OF COURSE !!!!

  • @MostlyBuicks
    @MostlyBuicks2 жыл бұрын

    My step father had a 1949 Ford 1 ton dually wrecker. He replaced the flathead with a 292. That engine was a towing monster. I also rode in a school bus every day which had a 292.

  • @muffs55mercury61

    @muffs55mercury61

    2 жыл бұрын

    I bet that was fun to watch. Our school buses were equipped with Chevy 235 6 cylinders.

  • @kevinmccune9324

    @kevinmccune9324

    2 жыл бұрын

    Those things didn't seem to have good starting torque, when you got them going they would chug to nothing and if oil changes were kept up they would run forever, they did have a problem with rocking arm oiling( theres was kit available to correct that) Also the firing order was strange, that gave them that funny sound.

  • @MostlyBuicks

    @MostlyBuicks

    2 жыл бұрын

    @@kevinmccune9324 My two favorite sounding engines through dual exhaust and turbo mufflers are the Ford 312 and the Buick 401.

  • @kevinmccune9324

    @kevinmccune9324

    2 жыл бұрын

    @@MostlyBuicks The old Buick was pretty popular with rodders back in the day, I had a "Mitchell" Dual exhaust system for My Brothers old 60 model Ford pickup,I do believe it helped it some doing away with the front crossover pipe, we may have even done away with the heat riser, not sure.

  • @andrewlevine8816
    @andrewlevine8816 Жыл бұрын

    The y-block is one of the most underrated engines ever. The shortest conrods are more than 6.2 inches long. They high swirl combustion chambers. The deep skirt design added strength. Everyone a side oiler. All had air gap inlet manifold. Had shafts mounted rocker arms Supercharged ones gave up to 360hp. They are great motors. Arguably one of the best small cube v8s Ford made.

  • @76629online

    @76629online

    9 ай бұрын

    Agreed.

  • @alkemy56

    @alkemy56

    7 ай бұрын

    Pertronics will fix that, had a unit in my 292 for 11 years and no problems at all. @denniswilson8013

  • @garychiuminatto917
    @garychiuminatto9172 жыл бұрын

    I owned a 56 Ford Customline with a 272 and a 3 speed manual on the column. Bought it used in 1965 from an elderly couple with 25000 miles. My dad’s personal mechanic had it parked at his place with a fire sale sign in the windshield. The mechanic told us he had taken care of it since new and it was an excellent car. I bought it, changed the oil and filter every 3000 miles and never had a problem one with it. Once in a while being a teenager I would take on a Mustang 289 2bbl and never lost. I cared a lot about the car and didn't race it very often. I knew it wasn't a hot rod but it could hold it's own with comparable cars including the 283 Chevys. I always used Valvoline oil and wish I still had it. It was in great condition, idled as quite as a sewing machine and ran perfectly when I sold it. I have a great respect for the Y block. I also worked for a company that had a 25 foot bobtail and a dump with 292s in them and never in the shop either.

  • @timfoxmail
    @timfoxmail2 жыл бұрын

    I rebuilt a 312, in 1966. I had heard about the problems with top side oiling and made sure that the machine shop that did some of the assembly also knew the secrets of the y block. I had no problem with top side oiling and the engine lasted a long time. Thanks for the memories.

  • @mumbles552
    @mumbles5522 жыл бұрын

    I had countless numbers of 292 and 312 motors in my '57 Ford hardtops and only threw a rod in one, a 312. It was the manual transmissions which wouldn't hold up to weekend drag racing. Low gear on the cluster would always break but installing a heavier trans with wider gears from a '56 Merc solved that problem. Also installing a 9" 4:11 geared rear end with leaf springs from a six cylinder '57 wagon with manual overdrive helped with the motors potential. Quite a few motors I bought already had the overhead oiler kit on them and lots were also full of thick sludge from using non detergent oil and running too cold from an owner removing the thermostat. They made the most beautiful exhaust rap by running straight pipe with 18" Thrush straight thru resonators up front instead of mufflers. Man, I miss those Y-blocks!

  • @TheFordf100

    @TheFordf100

    Жыл бұрын

    👏

  • @67marlins
    @67marlins2 жыл бұрын

    I ran a 292 in a '58 Ranchero, and I'll admit it leaked from the rear main, and burned its share of oil too, but was probably abused before I bought it. Honestly, it ran strong and didn't get bad gas mileage. Like a man said below, I wouldn't call it amongst the 'worst'.

  • @user-cs1ne8gx9u

    @user-cs1ne8gx9u

    2 жыл бұрын

    Agreed.

  • @KeithOtisEdwards

    @KeithOtisEdwards

    2 жыл бұрын

    I think that was an even worse problem than the cam-oiler galleys: the rear main oil seal, which leaked on all Ford engines for years. I remember coming home from work and noticing an oil spot on my driveway, and I knew at once a Ford had been there. (It was the lawn service truck.)

  • @cammontreuil7509

    @cammontreuil7509

    2 жыл бұрын

    Rope seal and burning some oil was normal. I never trusted an engine unless it burned a slight bit of oil.

  • @user-cs1ne8gx9u

    @user-cs1ne8gx9u

    2 жыл бұрын

    @@cammontreuil7509 agreed

  • @BD-xz6te
    @BD-xz6te2 жыл бұрын

    I have personal experience with the ford Y block. They were decent engines as long as you changed the oil regularly. I still have one in an old F350. It was never fast but for a truck of that era it always punched well above it's weight and it withstood years of abuse at the hands of a teenage driver who grew up on a steady diet of Smokey and the Bandit and Dukes of Hazard reruns. That's a tall order for any engine of that era.

  • @fadedjate7230

    @fadedjate7230

    5 ай бұрын

    What oil do you recommend?

  • @BD-xz6te

    @BD-xz6te

    5 ай бұрын

    @@fadedjate7230 Pretty much any good quality oil works, but you really should run some additive with zinc in it for older, non roller cam engines. I believe Rotella still has zinc in oils they advertise as being for diesels. Also I'm a big fan of Marvels Mystery oil for Y-blocks. I couldn't tell you why but it made the valve train on mine a lot quieter. I could pour some in with the engine running after an oil change, and the valvetrain would quiet down considerably. It would stay quiet until the next oil change. I still run some in my 63 Ford SD series 534.

  • @fadedjate7230

    @fadedjate7230

    5 ай бұрын

    @@BD-xz6te Probably gonna need lead additive as well.

  • @Thomas63r2
    @Thomas63r22 жыл бұрын

    Adam, I'm surprised that you seem to be unaware that the Y-block remained in production until ~ 1990 for the South American market. It was chosen for its durability.

  • @hendo337

    @hendo337

    2 жыл бұрын

    I thought it was till like 1976 in cars and 1977 in trucks...

  • @fastinradfordable

    @fastinradfordable

    2 жыл бұрын

    Yea but one year before Chevy small block. Was used in North America til like 2000s

  • @jeffrykopis5468

    @jeffrykopis5468

    2 жыл бұрын

    Just not terribly relevant to this channel, which is for American market cars. After all, the Cleveland was used in Australia into the 80s, and some French trucks had flatheads into the 90s.

  • @Thomas63r2

    @Thomas63r2

    2 жыл бұрын

    @@jeffrykopis5468 The French military flathead Ford V8's were the most evolved - fixing many of the design issues of the Flathead V8 last used in the U.S. in 1953. The French flattie is not legal to use in setting Bonneville land speed records.

  • @jeffrykopis5468

    @jeffrykopis5468

    2 жыл бұрын

    @@Thomas63r2 Yes, I know, they don't want you to have a reliable engine that can make 300 hp without blowing up 😆

  • @3rdpig
    @3rdpig2 жыл бұрын

    When I was a kid we had several cars with Y blocks, none of them were bad motors, they all ran well and had long lives...or at least as long as other engines of the era and were superseded by the newer small block, the 260 and 289, not because the Y block was horrible, but because Ford learned a lot and had incorporated those lessons into the new motor.

  • @tomnekuda3818
    @tomnekuda38182 жыл бұрын

    I had both a 292 and a 312 that I cammed and ran headers and 3 deuces on. It was very torquey and could be driven 80+mph all day. I set the valves at regular intervals and made sure that the oiling holes in the rockers aligned with the head. I loved the engines....not a lot of hp but plenty of torque. I always used good oil in them and changed at specified intervals. I always had wanted one with a Paxton on it but they were rare as chicken lips. Both were in 1957 Fords. One went nearly 300,000 miles and the other had a good 200,000+ on it. They used a bit of oil but not enough to have to add between oil changes. I would not classify these engines as "worst' engines at all.

  • @Bill-cv1xu

    @Bill-cv1xu

    2 жыл бұрын

    🤣

  • @MrTheHillfolk

    @MrTheHillfolk

    2 жыл бұрын

    I've heard a few of em over the years. I got a customer with a 57 Fairlane ,jet black and a set of cherry bombs and a little bit wider tires under it to fill it out nicely. Has a nice raspy poppin exhaust note to it.

  • @67marlins

    @67marlins

    2 жыл бұрын

    Little red....you know this isn't a forum for 8 year olds.

  • @user-cs1ne8gx9u

    @user-cs1ne8gx9u

    2 жыл бұрын

    Ya I think the worst is a bit hard on the old y

  • @michaelf.2449

    @michaelf.2449

    2 жыл бұрын

    @@user-cs1ne8gx9u I'd say all in all the worst Ford engines ever made probably came from the 2000's to 2010 all the engines before seem to be underpowered or complicated but nothing absolutely horribly wrong

  • @dionrau5580
    @dionrau55802 жыл бұрын

    The sound of the 57 Ford With straight pipes is glorious.

  • @JakeSanMartin

    @JakeSanMartin

    2 жыл бұрын

    A 292 with straight pipes is the equivalent of angels singing.

  • @MostlyBuicks
    @MostlyBuicks2 жыл бұрын

    Some people will NEVER learn the lesson of oil change intervals and using the RIGHT oil. Most people treat cars as appliances and do not do the maintenance needed.

  • @michaelf.2449

    @michaelf.2449

    2 жыл бұрын

    Till this day I'd say a majority of the cars that are scrapped for mechanical problems are from missed oil changes.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    FACTS.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@michaelf.2449 FACTS.

  • @Sundancer268
    @Sundancer2682 жыл бұрын

    My dad had a 1961 Ford with the 292, three Speed Overdrive and 3.89 rear end and we never had any problems with it. Dad paid $2250 for it and we picked it up April 20th 1961 and traded in his 1955 Plymouth Plaza 2 door sedan. Dad religiously changed the Oil and I got the car in 1968 for graduation. I sold the car in 1969 with 100,000 miles on it when I went into the Navy. Sometimes I still wish I had it, although I really miss my 1964 Galaxie 500 XL Convertible with the 390.

  • @hendo337

    @hendo337

    2 жыл бұрын

    Was it a Galaxie? I always thought the 1961 Starliner was the most beautiful of the 1960s fullsize Fords followed by the 1969 XL GT. 😋

  • @Sundancer268

    @Sundancer268

    2 жыл бұрын

    @@hendo337 Nobody said I could Spell.

  • @pattyeverett2826
    @pattyeverett28262 жыл бұрын

    My father bought a used 1959 Ford with the 292. He drove it several years with no engine issues. He sold it and got a used 1964 Ford(with the 289 I think) when it started having automatic transmission issues. We lived in a rural area, so there was no stop and go traffic. My mother was mad as she liked the 59. One the other hand, my grandfather had a 53 ford with the flathead. It was quiet as described. The low power did not matter as his top speed was 45 mph. It went 170,000 miles before a ring busted. He just got a re-built flathead which lasted till he passed away. (He was the same with his televisions, he replaced the picture tube 3 times in his early 1950s TV instead of buying a new one)

  • @sking2173

    @sking2173

    2 жыл бұрын

    I would have liked your granddad ...

  • @pattyeverett2826

    @pattyeverett2826

    2 жыл бұрын

    @@sking2173 He lived in a rural area, so 45 was ok. Now there are lot of oil field trucks running around, so it would be dangerous.

  • @dmandman9
    @dmandman92 жыл бұрын

    My dad loved the 292. He stated that their main problem was a lack of lubrication to the rocker arms. But their was a popular workaround that involved running another oil line from the oil sending unit through the valve cover to the rocker arm.

  • @Roman-rz3qj

    @Roman-rz3qj

    Жыл бұрын

    Yes! They had a poor oil distribution problem. This extra oil mod is crucial for these engines. Thanks for this comment. I was going to write something about this.

  • @johncoops6897

    @johncoops6897

    Жыл бұрын

    @@Roman-rz3qj - Yet those things were already covered in the video.

  • @TheCatOfAges

    @TheCatOfAges

    Жыл бұрын

    @@Roman-rz3qj incorrect information. The external oilers often kill your engine because they steal oil-pressure from the crank and often make them throw rod bearings. The best cure for oiling? Clean your oiling passages, and run compressed air at the oil pressure sender. These engines oiled perfectly fine stock, with good oil.

  • @toronadogofast7868

    @toronadogofast7868

    9 ай бұрын

    We got around the cooking and sludge issues by draining the oil, reinstall the plug and fill it back up with number two diesel and let it idle for ten minutes. Drain it change the filter and add oil. We would also add about half a quart of ATF in the engine oil the other half went into the fuel tank. Kept everything clean and lubricated.

  • @marzsit9833

    @marzsit9833

    9 ай бұрын

    @@TheCatOfAges not incorrect information: the y-block had a design issue where the rockers received oil through passages that ran to one of the cam bearings, the cam bearings were oiled through a hollow camshaft. however, that cam bearing had a reputation for rotating in it's bore, cutting off the oil supply to the rockers. the solution was to add the overhead oiling kit, but lots of the kits were installed incorrectly. there were special fittings with drilled orifices to limit the oil flow but 'smart' installers didn't use them, thinking they knew more than the engineers. the problem still exists with y-blocks, rebuilders never did find a way to prevent that bearing from rotating.

  • @racekar80
    @racekar802 жыл бұрын

    There is a competition for old engines that are hot rodded, they dyno them and there is a Y block builder that either wins or is near the top every year. The engine has a lot of potential.

  • @hendo337

    @hendo337

    2 жыл бұрын

    Yes, the Y block has done well in Engine Master's competition.

  • @MrTheHillfolk
    @MrTheHillfolk2 жыл бұрын

    I've got an old Hastings rings basic engine rebuild guideline manual and it lists how to perform all the oiling system fixes for these.

  • @Sedan57Chevy
    @Sedan57Chevy2 жыл бұрын

    Ford always had excellent styling, fantastic interiors, and excellent market planning (who doesn't love the first gen thunderbird), but sometimes they dropped the ball with the mechanical parts and it's a shame. Still, I'd take living with a Y-Block over most modern engine designs that you can't work on.

  • @strongereveryday2302

    @strongereveryday2302

    2 жыл бұрын

    Its because they have never innovated anything. They copy and make derivatives. Anything they did originally is terrible. Including everything modern. The new Explorer is categorically the least reliable vehicle on the planet.

  • @Primus54

    @Primus54

    2 жыл бұрын

    Sedan57Chevy, I agree with most of your comment with one HUGE exception. Can you say “Edsel”? 😉

  • @davesgarage78

    @davesgarage78

    2 жыл бұрын

    Agreed, I've had several Fords and every one of them were styled well, Comfortable, good quality fit and finish and had average if not underwhelming powertrains both in fuel mileage and reliability

  • @sorshiaemms5959

    @sorshiaemms5959

    2 жыл бұрын

    @@Primus54 EDSEL S DIDN T HAVE Y BLOCKS

  • @mauser2134

    @mauser2134

    2 жыл бұрын

    @@strongereveryday2302 lol they never innovated anything? what a stupid thing to say. the problem people have with ford is they always change. gm kept the same shit for years and because of that the aftermarket supports it well. gm engines are for simpletons.

  • @scottadams9226
    @scottadams92262 жыл бұрын

    I had a 62 Galaxy that had a 292 that ran better than any engine that I ever had. It was the quietest engine I ever heard and I could pretty much start it anytime just by turning the key. I used to have the window down and reach in and turn the key and many people around said they never seen an engine run so good that didn’t have fuel injection.

  • @Lousybarber
    @Lousybarber2 жыл бұрын

    My dad owned a '53 Ford pickup with the last flathead V8. Had drove that truck for almost 20 years. He once told me he was glad to have a '53. The '54 model was noisy since it was an overhead valve design. I was not aware that it had oiling problems on the top end.

  • @billnasburg1361
    @billnasburg13612 жыл бұрын

    I have a 57 Thunderbird with the 312 and it was rebuilt by a Ford expert and runs so perfectly and sounds so good with it's unique exhaust note

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    Our family car back in the 1950S was a 1956 Meteor Rideau With a 312 thunder bird specials. Dad used to say it would pass any thing on the road but the Gas station. Dad traded that Car for a 1959 Chevy with a 283, What I remember is Dad saying how gutless it was compared to the old car.

  • @dave1956
    @dave19562 жыл бұрын

    Anyone remember the Frantz Oil Cleaner? I had a car that had one installed. You would change a roll of toilet paper that filtered the oil. You still had to do oil and filter changes, but at longer intervals.

  • @keithstudly6071

    @keithstudly6071

    2 жыл бұрын

    That's called a Frantz oil filter. You can still buy them.

  • @thecollectoronthecorner7061

    @thecollectoronthecorner7061

    2 жыл бұрын

    Ive used them have one in use now. Replace with John Wayne toilet paper. Its not a oil filter . Its a Frantz oil cleaner. I am convinced that it does what the manufacturer claimed.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    I remember those. Neighbor had a 62 Buick with one.

  • @ajwilson605

    @ajwilson605

    2 жыл бұрын

    Had one on a '60 Ford Falcon 170 CID I-6. I set up the return line to feed oil to the rocker shaft as the rockers ran dry because of sludge and cam bearing issues.

  • @waynelovejr.1005
    @waynelovejr.10052 жыл бұрын

    In 1976, I bought a '56 Ford pickup, with a 292, for $100 from a junk yard. I changed oil and filter, adjusted the valves, installed new valve cover gaskets, tuned it up, and rebuilt the carb. I then drove the truck to work ( 40 miles a day), for over 2 years, ( It never used oil, or let me down). I then sold it to my brother, who used it for another couple more years, then he sold it to a guy that hauled junk. That guy drove it another year before it finally gave up. It had developed an oil leak, and he ran it out of oil. Originally, the guy at the junk yard thought it had a rod out of it, but the solid lifters just needed adjusted. So, I think the "Y" block was fine for it's intended purpose.

  • @ubertalldude
    @ubertalldude2 жыл бұрын

    Loving this channel, you do a great service talking about the heydays and malaise days of all the great American automakers. I really enjoy hearing you talk about these engines, cars, etc.

  • @ryancampbell1252
    @ryancampbell12522 жыл бұрын

    The Y-block continued on in South America until at least the mid 80's. Sometime in the 70's Ford came out with what they called the phase 2 Y-block which changed the head, intake and exhaust configuration. I run the early version all the time and never have a problem with them.

  • @mbarker_lng
    @mbarker_lng2 жыл бұрын

    The oiling kit reminds me of a similar kit that was sold to remedy a problem in the early 80's Honda V4 powered motorcycles. It was found that the oil supply was insufficient in one of the heads (IIRC it was the rear one) when the motorcycle was idling. Although some thought the real problem might have been the cam material was too soft, the result was the same- worn cams. Whatever the case was, the oiling kit would fix it by adding a direct supply to the cam area. EDIT: One other thing, on the quietness of certain engines- there was a mindset in the early decades of automobiles that "quiet = quality" so much effort was spent to make cars, esp luxury cars, to run quietly (even though the concepts are not actually related)

  • @toronadogofast7868

    @toronadogofast7868

    9 ай бұрын

    Same with the most LA engines. 273, 318, 340,&360. We would add a copper line inside the on #2.

  • @KenanTurkiye
    @KenanTurkiye2 жыл бұрын

    The amount of messages beginning with ''My dad had a....'' is amazing, ahh the nostalgia. : )

  • @leonarddean8800
    @leonarddean88002 жыл бұрын

    I had two 292s in trucks and really liked the engine. They were durable for us. We rebuilt both engines when we first got the trucks and never had any problems. They were a little tricky to get the cam gears timed correctly when you're putting them together. We would find a exhaust manifold for the left side that dumped out the back and did away with the front crossover pipe.

  • @toronadogofast7868

    @toronadogofast7868

    9 ай бұрын

    Would do the same, but run straight stacks with the metal flappers.

  • @74rockon
    @74rockon2 жыл бұрын

    Hello Adam I’ve been watching your videos for a while now and you have a fantastic collection of super clean nice original low mileage cars and I particularly like your ford and mercury collection as I’m an avid ford fan well done sir! I have been exposed to the y block at a very young age as my father had bought a tu tone green 55 crown Vic in 1978 in butte Montana with a replacement 292 out of a 59 or 60 ford and all the years he drove it he never once had an issue and it always ran superb. He wanted to rebuild the whole car in 2000 and always wanted a 312 engine and that’s what he’s going to install into it and nothing wrong with the 292 at all. I own a few 59 fords and in the one it came with a 292 it was an oil burner but always started Right up and ran without issues and about 8 years ago I replaced it with a rebuilt 272 a friend was selling out of his 57 ford and all I did was add a holley 600 4 barrel pertronix ignition and I faithfully change oil in it and I’ve never had an issue. No I don’t drive it everyday and only drive it in summer but it performs flawlessly and gives me almost 19 mpg and is an automatic.the 3 major strikes against the y block was the misaligned cam bearings starving the upper portion of the engine for oil the tiny wee oil hole in the cylinder heads that once they clogged up starved the upper portion for Oil the rear main oil seals Would leak on the earlier ones and lastly lack of oil changes coupled with poor oil of the times along with if you drove on lots of gravel roads really shortened the life of them as that oil hole in the head would plug up even quicker. Other than that they are a good engine that gives decent performance and will last quite a long time if looked after properly. Yes it was quite the transition from the flathead and guys were likely shocked at this new fang dangled v8 but ford needed to put some power into there cars and get with the times as overhead valve v 8s were beginning to be the norm. Thanks for your video and I too would not consider a y block a worst engine as they for the most part got largely misunderstood.

  • @dennisdaly907

    @dennisdaly907

    2 жыл бұрын

    Yes!- Finally! - a mention of the cam bearings turning in their bores and blocking off oil to rocker arms.. That was the biggest issue with the old Y blocks I ran across in the mid-sixties...Pull the cam and stake the bearings or install an oiler (ugh) kit. I gotta say, though, You could neglect/ abuse and run 'em rough, and when those mains started thumpin' (the main reason for the rear main oil seals going out)- and rods began to knock, those beasts would still start right up in the dead of a North Country Winter.

  • @whathappened2230
    @whathappened22302 жыл бұрын

    My family had a camper bus made from an old school bus. 312 ford Y block. At over 100k it would still do over 70 mph with us and all of our boats and gear. Take care of it and it will run a long,long time!

  • @dougpersell8776
    @dougpersell87762 жыл бұрын

    I have a 1963 f600 . I used it about a year with the 292 i was very impressed with it . It has a dump bed i hauled alot of 6/8 ton loads of gravel with it . It was very impressive for a small engine once it got rolling it wanted to go turning more rpms than i wanted . It had a rear main oil leak when i pulled the main it needed bearings so i found a wrecked 64 with a rebuilt 330. I was told i would be disapointed in the 330 after using the 292. It has about the same power but it dosent want to go like the Yblock did the 292 in a truck needed a governor. I never thought much about the ford Y blocks i always had chevy trucks. I have never heard any thing bad about the Y block from anyone that had and used one. Yes they are very dated today and not much of a build able hotrod engine but in a truck or daily driver there ok. In my mined after running one over 5000 miles hauling heavy loads the Y block will always be one of the best things i ever owned that came form Ford.

  • @hendo337

    @hendo337

    2 жыл бұрын

    The Y-block has won Engine Master's competition in the Vintage category a number years.

  • @frankpeletz1818

    @frankpeletz1818

    2 жыл бұрын

    I worked for a school district. EVERY one of the 350 Chevy/GMC 66 passenger busses would break a crank at 20,000 miles..The 361 Fords weren't too bad. But yes, a 330 was about as useful as a 300 6 cylinder.

  • @scootergeorge7089
    @scootergeorge70899 ай бұрын

    I owned a 1957 Ford Ranchero with the 292 "Thunderbird" V8 engine. Heard stories about lack of oil to the top end so I started it with the valve covers removed. What a mess. OIL EVERYWHERE! A great running engine. With overdrive and the factory 3.89 diff, 20+ MPG at 60 MPH. A friend had a 1954 3/4 ton pickup with the original 239. That was a very reliable engine. The Navy used a mobile generator powered by the Y Block, called the NC-5. No engine problems that I was aware of but they had a bad habit of jumping into gear and racing across the flightline.

  • @MostlyBuicks
    @MostlyBuicks2 жыл бұрын

    Well after Ford introduced the 352 in 1958, they radically detuned the 292 and it was also Ford's last year for the 312 (used in some Mercurys). I had 6 312s in my life--three 1956 T-Birds and three 1957 T-Birds. They were fantastic engines. When restoring this 6 cars, I rebuilt each engine. I also had one of those radically detuned 292s in a 1960 Mercury, and it sucked. Yes, they had oiling problems because of two things: 1. People just refuse to maintain their cars, always have, always will. And since these engines had solid lifters, people typically used non-detergent oils. Bad idea. If you changed the oil and filter every 2000 miles and used a high grade detergent oil, you will probably never have trouble with upper oiling problems. Just about every year I made the 4500 mile round trip from Tucson to the Twin cites area via Denver with my T-Birds.

  • @will7its

    @will7its

    2 жыл бұрын

    Most people dont know what the numbers mean on the oil bottle so detergent vs non detergent is really pushing it with the average joe.....

  • @spaceghost8995

    @spaceghost8995

    2 жыл бұрын

    Every 2000 miles? Who wants to do that? Most of my life I have changed oil just twice a year regardless of mileage! Of course I drive Hondas and Toyotas.

  • @MostlyBuicks

    @MostlyBuicks

    2 жыл бұрын

    @@spaceghost8995 Back then 2000 was about right. With modern cars I go every 5000 miles. Cheap insurance.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@will7its In the 50s and 60s, detergent oil actually said it was detergent on the can. Many people, myself included, didn't trust detergent oil, as it would sometimes separate. Eventually, they fixed that problem.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@spaceghost8995 You are not supposed to change the oil that seldom, unless you do very little driving. And just because your engines start and run does not mean that they are in good condition. I have had people tell me how wonderful their engine is, only to hear bearing knock when they start it, which is NOT good.

  • @hendo337
    @hendo3372 жыл бұрын

    The Y block was used in Brazil until around 1977.

  • @elizabethcarlson1321
    @elizabethcarlson13212 жыл бұрын

    i loved my 292Yblock. I am a solid Chevrolet man, but the sound of a Y block on glass packs just off idle.....Sweet! I agree that the oil requirements were the big challenge with them. If you kept good oil in them and not let them leak, they were great!

  • @yuvegotmale
    @yuvegotmale2 жыл бұрын

    My dad had a auto repair shop in the 40s thru the 70s. He did a lot of conversions on the the Y block to get oil to the rockers. I remember it had copper tubing being plumed right into the valve covers. I had a few flatheads back in the day..great sounding engine but it had some inherent issues, overheating, burning valves, vapor locking and breathing issues...a bit asthmatic to say the least.

  • @monarch1957
    @monarch19572 жыл бұрын

    I have a 57 Monarch with a 312 Y block and had the car since 86 and it's been a reliable engine never let me down all those years, the previous owner had the engine rebuilt with 30 over pistons at around 75,000 miles and have just over 90,000 miles on the car now.

  • @johnkrag6
    @johnkrag62 жыл бұрын

    They are a bullet proof engine. The original "side oiler". The problem with engines back then was sorry oil. When a y-block comes into my machine shop I make sure the #3 cam journal oil groove is deep enough. Back in the day as the camshaft wore into the babbitt bearing material it closed off the shallow oil groove. Plus I block off the oil drain tubes on the rocker shafts to pressurize the rocker arms. Keep quality high zinc oil in these engines and they'll for ever. Two other guru's of these great engines is Tim McMaster owner of Hanford Machine Shop in CA and Ted Eaton of Eaton Balancing in TX. They race these engines........

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    FACTS.

  • @travyboy5947
    @travyboy59472 жыл бұрын

    My grandpa had a 1956 Ford with a 272. It was a straight 6 3speed column shift, a dealership had replaced the i6 with a v8 before he bought it. When he got it, he put overhead oilers on it. Supposedly it was a wonderful car

  • @christownsend7602
    @christownsend76022 жыл бұрын

    Where I grew up it seemed like most of the farm trucks had Y block engines in them and a common modification was to take advantage of the cross over exhaust and run the exhaust pipes out through the hood for use in the wheat fields during harvest time to help to not catch the field on fire while working with the threashers.

  • @gormanwpjr
    @gormanwpjr2 жыл бұрын

    I never thought much of the Y Bock engines, due to what I witnessed back when the cars were 10 to 20 yrs old. They leaked oil, burned oil, had burned valves, etc. The Chevy 283, in comparison were fantastic used cars when I was in High School. That was the beginning of the 1957 Chevy becoming the icon that it is today. So, I never cared for the Y Blocks, but then 4 years ago, I bought a 1957 Ford Skyliner with the 312 Y Block. While I drive it very little, and I assume that the engine has been rebuilt, it starts amazingly fast, runs very smooth, has good power, and I absolutely love the sound of the exhaust. I have heard different theories as to why it sounds sort of like a Harley Davidson motorcycle, including the exhaust manifolds paring of the exhaust, and or the firing order, and others. I am not sure what the reason or reasons are? But with the Flamethrower mufflers (not loud - just a nice note), the exhaust sounds so cool under moderate acceleration. Do you have any thoughts on the exhaust sound? kzread.info/dash/bejne/loaj2Nekl6fPhZM.html

  • @sking2173

    @sking2173

    2 жыл бұрын

    Those Skyliners were beautiful, especially if they had an FE under the hood !

  • @johnsalvaterra1355

    @johnsalvaterra1355

    2 жыл бұрын

    Chevys burned oil, but nobody cared.

  • @sking2173

    @sking2173

    2 жыл бұрын

    The Y-blocks often had that choppy exhaust note because they ran around on six or seven cylinders after kicking out a pushrod or two because of the valve-train wear ...

  • @frankpeletz1818

    @frankpeletz1818

    2 жыл бұрын

    @@johnsalvaterra1355 283's did not use seals on the valve stems.

  • @doug960
    @doug9602 жыл бұрын

    GM came out with their small block at the same time. The venerable small block served as the yardstick against which all other engines were compared for such a long time. The GM smallblock greatly overshadowed the Y block. However, as others have said here, detergent motor oils were a new thing in 1954. If you used the best oils available at the time, the Y block was decently reliable compared to other engines you could have owned in 1954. I think people initially approached the Y block the same way they did the flathead it replaced, which would run on just about any flammable liquid laced full of dirt and twigs, and also just about any oil suitable for the ambient temperature. Sort of how we got used to conventional oil in engines from the 70s and 80s and had to switch to synthetic in the 90s and 2000s as many cars went to overhead cams, variable valve timing, auto lash adjusters, etc.

  • @charlescline4352

    @charlescline4352

    2 жыл бұрын

    If that is true why did the Y-Blocks dominate NASCAR during the mid to late 50's. Look it up if you don't believe me.

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    @@charlescline4352 one reason for teh confusion was G M preached about the 265 being a performance engine while ford was raving about having a padded dash. The people that hung around the race track knew Ford was faster. the people that don't believe it can watch Daytona Beach 1957. The 368 Merc and a 312 super charged Ford run away from the field, Both of these engines were y blocks..

  • @doug960

    @doug960

    2 жыл бұрын

    @@charlescline4352 Because they introduced the VR57 supercharger before Nascar introduced rule changes. Don't get me wrong, Y blocks are not bad engines, are cool and can make respectable power with modern technology, but they were and still are comparably heavy and limited in terms of displacement potential. The only option Ford had to make them competitive in the mid 50s was forced induction. Chevys were just as competitive if not more competitive naturally aspirated with Rochester fuel injection. When Nascar forced rule changes including 4 barrel carbs shortly after, the Y block just wasn't as adaptable as the GM architecture, and also wasn't as big a commercial success. It had reached it's limits by the 60s. Ford had to move to the FE, which shared some design features, but was a completely different engine. Ford did have a successful race program in the mid to late 60s, but they weren't selling many 427s to the public and GM and Chrysler big blocks offered to the public spanked the 390. It took them a while to catch up with the 428 and the 385 series.

  • @robertchristie9434
    @robertchristie94342 жыл бұрын

    My dad had a '55 Fairlane with a 272 Y-block, bought it new, no problems, drove it to the junkyard in '66 due to severe structural rust. He replaced it with a '62 Wagon with a 292 Y-block and with 4 teenage drivers it wasn't babied, no troubles and was sold with well over 100K in '71. A lot of family members owned Y-block '54 -'62 Fords and Mercs that ran fine. The only common issue was failing water pumps at around 40K miles. No problem changing them. Otherwise, they seemed to be very reliable motors. The flatheads had their issues too. I had a '51Merc, '50 and a '51 Ford that had vapor lock and would overheat in hot weather. 265 and 283 Chevy V8's back then leaked oil and some of the gasket material was crap. Mr.Gasket made a fortune with replacement kits.

  • @Cameraman148
    @Cameraman1482 жыл бұрын

    I owned and drove several Fords with the Y block engine 2 1956's and 2 1957's also a 1962 Ford SW, The Fifty sixes had the Thunderbird 312 ci and the 1957;s had a 292 and a 312 bird, all 4 barrel carbs except the SW .never any major upper engine problems. except they smoked on the vent tube because they did not have a PCV valve...I changed the Oil very often and used a upper Lube for the Valve Train as extra protection, because they were Cast Iron, I ran one 57 low on oil and drove 12 miles home, it got hot but did not lock up...old school but very fun to drive, and with glass packs they sounded great....cheers

  • @user-cs1ne8gx9u
    @user-cs1ne8gx9u2 жыл бұрын

    I've got a lot of experience with y blocks and your take is pretty accurate although I wouldn't call them the worst. If they had today's oils back then they would enjoy a much bigger following now. I've had many over the years and rebuilt correctly they don't suffer any issues with today's oils. Their biggest problem today is their weight and limited displacement potential for the hot rod guys that want a bunch of power. But they were a very solid strong block that wears well with the 292 and 272 being the best for a build having the smaller mains and therefore more meat in the block. Ford Argentina used the Y Block with some locally designed, more typical port heads up into the mid 80s if I remember correctly and were a lot more popular in south America. Thanks for the video.

  • @thecollectoronthecorner7061

    @thecollectoronthecorner7061

    2 жыл бұрын

    How come the GM Dodge Ford flatheads etc. Did not suffer ill effects from those same oils? Why did the FE not have the same problems. Why did the later Y blocks have a groove cut around the center cam journal. Its the poor compression rings and lack of PCV that created excessive blow by making the sludge and goo we found in every Y Block We tore down.

  • @user-cs1ne8gx9u

    @user-cs1ne8gx9u

    2 жыл бұрын

    @@thecollectoronthecorner7061 oil sludge is usually a problem of contamination be it water or hydrocarbons. Poor crankcase evacuation definitely exacerbates the problem. Sludge is a weird phenomenon I've come across in a few engines that aren't known for it. Like a Windsor I had the pleasure of swapping the intake out a while back. Or the 83 Chevy wrecker (350) my uncle bought cheap where you couldn't even see the rockers without digging with a screwdriver. How the previous owner's handled maintenance I haven't a clue, but it can happen to anything if the conditions are right. The y block definitely could have had a better solution but in my experience it's never been an issue and I've had many of them pass through my hands over the years. I've currently got a 63 f250 with it's original 292 completely stock in my side driveway right now that gets used weekly as a parts runner. It sat for years before I bought it and after rebuilding the brakes, carb, setting the lash and a complete ignition tune up it's been great.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@thecollectoronthecorner7061 That's how you fix early Y-blocks - groove the center cam journal, or use a later camshaft with the groove, and plug the oil bypass hole in the rocker shaft. Then you have a great engine.

  • @user-cs1ne8gx9u

    @user-cs1ne8gx9u

    2 жыл бұрын

    @@michaelbenardo5695 agreed

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@thecollectoronthecorner7061 No engines came from the factory with PCV before about 1963, except for those intended for the Armed Services. My aunt's neighbor did have plugged oil drainback holes in his 332 FE. I cleaned them out for him and scolded him for not regularly having the oil changed. The reason for the groove in the center cam journal was so the rocker shafts would have a continuous, rather than intermittent, stream of oil. A continuous steam is less likely to plug up. Lincoln did the same thing with their new 368 engine for 56. Flatheads did not suffer the rocker oiling problems because flatheads don't have rocker shafts.

  • @wildman510
    @wildman5102 жыл бұрын

    Those minor issues aren't really enough to make it bad, plenty of good engines have had design flaws and after they were fixed were great. Like the Ford FE which is known for tending to bend pushrods

  • @TheCatOfAges

    @TheCatOfAges

    Жыл бұрын

    Well, stuck valves rather. If they sit they usually stick.

  • @Bbbbad724
    @Bbbbad724 Жыл бұрын

    The Y, if you choose this mission contact John Mummert and Royce Brechler. Mummert casts aluminum heads and intakes. He can also fix you up with a supercharger intake and with the rear distributor, a. 184 series even fits. Mummert can also get stroker kits and cross bolt mains. The first engine I built was my Dads Y block. The 2x4,ECG cam, heads and intake on a bored and stroked 320 ci. 2x4 intake. BTW the MEL and 385 were bros. The 368 Turnpike Cruiser and FE were bros. The 289 replaced the Y block.

  • @johnphillips2396
    @johnphillips23962 жыл бұрын

    My great uncle had a sedan with the 292 . It had 120K on it with just tune ups ,oil changes two water pumps and a valve job.

  • @TheCatOfAges
    @TheCatOfAges2 жыл бұрын

    I disagree... the Y block has been extremely fun to work on and repair, as long as you kept oil changes on time, and used Halvoline over some shitty quaker state.

  • @MostlyBuicks

    @MostlyBuicks

    2 жыл бұрын

    Yeah so many people used Pennzoil or Quaker State back in the day. These paraffin oils are sludgy flakey messes. Every engine I ever torn down with these oils were so dirty. Engines I tore down with Valvoline or Castrol were typically very clean.

  • @tomnekuda3818

    @tomnekuda3818

    2 жыл бұрын

    You're sure right about the Quaker State.

  • @jeffrobodine8579

    @jeffrobodine8579

    2 жыл бұрын

    @@tomnekuda3818 The Green Monster.

  • @hendo337

    @hendo337

    2 жыл бұрын

    I always buy Havoline 10w-40, the 6qt box is cheaper per Qt than even Supratech or Rotella at Walmart.

  • @randymagnum143

    @randymagnum143

    2 жыл бұрын

    @@hendo337 shell Rotella or Chevron Dello are as good as any oil you can buy

  • @tommcmillan3143
    @tommcmillan31432 жыл бұрын

    Great video Adam! My Dad had that engine in his 61 Ford sedan, I was pretty young but I just remember him very unhappy with that engine. Prior to that he had a 51 Mercury which he absolute loved, I think you described exactly why he was so disappointed after having a flat head in the 51. The 61 Ford ultimately caused him to change his loyalty to Chrysler when he traded it for the 65 Fury III. After that experience, he only bought Chrysler products for the rest of his life.

  • @GOD-mj9wt

    @GOD-mj9wt

    2 жыл бұрын

    Tell me about that fury

  • @tommcmillan3143

    @tommcmillan3143

    2 жыл бұрын

    @@GOD-mj9wt It was 4 door hardtop, dark blue metallic paint. It had a very nice light blue/silver interior, very classic styling. The car had to haul 4 young kids and we rode in it with comfort. We took many high speed trips from Warren to the cottage up north and we never broke down, much better than the 61 Ford:)

  • @doneB830
    @doneB8302 жыл бұрын

    I’m learning so much from you, mechanics never stop learning.

  • @adamgallahan6747
    @adamgallahan67472 жыл бұрын

    my dad has a 1964 ford fl00 that an uncle bought brand new and its still in the family. It’s mostly dent free but doesn’t look the best visually but it’s all the same original red color but it has a four-speed manual and the 292 y block and man it runs amazingly! has great sounding exhaust, headers and I’m gonna guess like maybe 2 1/2 inch exhaust that goes to two cherry bombs and then turns out right in front of both rear tires sounds so good no H pipe or X pipe or anything. We’ve had that thing loaded down countless times and sometimes much beyond its capacity, you could just tell by how it was sitting so low in the back when loaded down and that engine handled it and still handles it like a champ, Dump runs, hauling wood etc.

  • @MrMopar413
    @MrMopar4132 жыл бұрын

    In my youth I had a 62 F-100 with a 292 in it. It had its issues just like any engine in those days , that all engines had. No PVC system so engines slugged up big time, no matter the manufacture as people got used to using detergent oils and changing oil and filters together at the same time. The Y-block engine was pretty much indestructible but the big issue with them was the intake port design which was offset 90 degrees , top n bottom compared to the small block Chevy and Chrysler that where side by side. Who in the hell came up with that stupid intake port design and thought it was good is beyond me. If the YBlock had a side by side intake port design it would have made a lot more horsepower. Another issue was the Y-Blocks that I’ve worked on is after a long time the distributor in the back was notorious for sticking solid to the block, we’d have to get a big pipe wrench on them to get them unstuck. Other then these issues it was a good engine and would take a hell of a beating and keep on ticking.

  • @christopherkraft1327
    @christopherkraft13272 жыл бұрын

    These engines are from a simpler time with no smog devices & catalytic converters!!! They were easy to work on too!! Thanks for sharing another interesting porch chat!!! 👍👍

  • @makkepuu
    @makkepuu2 жыл бұрын

    Still running a 272 in a '55 Country Sedan. Stock 2bbl paired up with 3speed + od. Always used good oil, never a problem. Only problem is the steering box, the adjustment is maxed and I haven't been able to find renewed or better shape manual steering box

  • @2strokepower803

    @2strokepower803

    2 жыл бұрын

    I have a 272 in my 55 fairline town sedan. Also with the small 2 barrel. When we rebuilt the engine we got it bored over to be a 292

  • @TheCatOfAges

    @TheCatOfAges

    Жыл бұрын

    Must have only been driven in town, my '57 is still at minimum pretty much and steers like brand new

  • @jwelchon2416
    @jwelchon24162 жыл бұрын

    My dad said a problem with the Y blocks is that they had solid lifters. He told how wonderful the FE engines were in 58 with hydraulic lifters. It eliminated all the valve clatter.

  • @robertsnyder5149
    @robertsnyder51492 жыл бұрын

    You are blowing smoke again,the oiling problem came from misalignment of the oil hole to it's mate in the head. I took the heads off and oblonged the oil passage hole and problem solved.

  • @sking2173

    @sking2173

    2 жыл бұрын

    The problem you identified was only one of three with rocker shaft oiling system. The others were: the cam bearing issue; the rocker shaft overflow tube (poor design). All the of these issues combined to grind the hell out of rocker shafts. Three strikes ... Horrible design ...

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@sking2173 The big problem with the early ones - 54 - 56, was the fact that the center cam bearing journal didn't have a groove, and that rocker overflow tube. Groove the cam and plug that overflow, and you have an excellent engine.

  • @sking2173

    @sking2173

    2 жыл бұрын

    @@michaelbenardo5695 - Yep, but picture this: Muncie, Indiana, summer of ‘58. A middle-class suburbanite with his 2.5 kids working his 9-5 and juggling his spare time between his wife and his girlfriend. The last thing he wants to hear is that what started out as a seemingly harmless tick under the hood of his ‘55 Fairlane will now require a motor-out cam bearing replacement that will cost him more than two-week’s wages. Since his young daughter is in dire need of braces and his girlfriend’s ‘52 Ford, that he had bought for her with money he squirreled away without his wife’s knowledge, needs a clutch, he decides to put off the repair on his car for a month or two. Six months later, he’s lost his girlfriend because her car now needs a valve job that he can’t afford, has a mad wife that has found out about the girlfriend because she spotted the missing money he used for the clutch job on the girlfriend’s car, a daughter with beautiful straight teeth that won’t even speak to him because of his infidelity, half a kid that’s never home and will never amount to anything, and a ‘55 Ford that he’s embarrassed to be seen driving because it now sounds like a thrashing machine - and he still can’t afford to fix it. Do you think this guy will buy another Ford ??

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@sking2173 If this was his first Ford, probably not, but if he always had good luck, except for this one, he probably would. Now if the next one is bad, that's a different story.

  • @DRILL-SGT.HARTMAN
    @DRILL-SGT.HARTMAN2 жыл бұрын

    My Dad was born in '29 and had first hand experience with them. He told me about having to install side oilers. He hated these engines, but had almost always driven Fords up to this point. He said he owned a couple with 292's and one 312. He told me he avoided the Y block because of his bad experiences with them. From talking with him, I gathered that a lot of people had the same opinion of them.

  • @roccofortura2468
    @roccofortura24682 жыл бұрын

    great knowledge and information, thank you.

  • @commandtheline
    @commandtheline2 жыл бұрын

    I had a project pick up as a teen in high school. 59 F100. Had a 292 in it that snapped the cam and sent it through one of the Pistons. Interesting to learn about the cam oiling I had no idea and certainly didn't at the time. High School shop class I pulled the motor and got a donor 239 and had it bored for 272 and reuse the 292 heads.

  • @tonychavez2083
    @tonychavez2083 Жыл бұрын

    Nice info thanks.. I think despite these oiling issues they were still incredible workhorse motors that powered America in many forms for many years, many with minimal maintenance or care. They soldiered on until they died literally. Kinda like the late 2 valve Triton motors in school buses and work trucks around the country..

  • @chuckselvage3157
    @chuckselvage31572 жыл бұрын

    The forgotten Ford motor they didn't get much love but they did redeem themselves with the FE which won everything in motor racing.

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    the FE took over from were the Y block left, in 1957 the Y was the boss look at the NASCAR records.

  • @chuckselvage3157

    @chuckselvage3157

    2 жыл бұрын

    @@mylanmiller9656 ok I will.Anything else?

  • @edwardpate6128
    @edwardpate61289 ай бұрын

    My mom had a 56 Ford Victoria and I remember as a small kid my dad putting one of those rocker arm oiling kits on it, probably around 1963 or so.

  • @thoof2001
    @thoof2001 Жыл бұрын

    The first thing mentioned regarding oiling problems in this ‘worst’ Ford engine is owner negligence i.e. using non-detergent oil. Next was badly-installed bearings in rebuilt samples. Sounds like the engine itself was a good design, save for the crossover exhaust pipe.

  • @automatedelectronics6062
    @automatedelectronics60622 жыл бұрын

    The "Y" blocks were great engines. The Fords benefited from having a 3-speed automatic transmission, although until 1956 or the 1958 Cruise-O-Matic, they normally started in 2nd gear. With the Lo position, it allowed the fords to move off the line quicker than a Chevrolet with a PowerGlide. OK, the "Y" blocks were very reliable and long-lasting engines. Their life and reliability depended on a large part to regular maintenance. We resurrected a 1960 Ford Sunliner a few years ago. It pretty much had sat at a vacation home, rarely driven, for the last 50 years when we got it. The top-end was slugged up and we had to pull the heads and do a valve job. We used to see lot's of much newer slugged up engines, and it wasn't from not using detergent oils. Nearly everytime, we found that they had used Penzoil and changed it at factory intervals. It was the ash in the oil. Not so much a problem with Quaker State and NEVER a problem with Castrol, Valvoline or other Western oils. Well, after the valve job, the engine ran like new(the car didn't have that many miles on it). At the same time, I pulled and resealed the Cruise-O-Matic transmission. As these used metallic clutches, they were in great shape, so I re-used them. The lined bands were replaced, as well as all the gaskets and seals. After that job, I took on a 1956 Ford T-bird, with a 312 V8 and Ford-O-Matic. After disassembling the engine, everything looks good, but the customer wanted it rebuilt. Everything was within tolerances so the engine was cleaned up and new rings and bearings were installed. The heads got hardened valve seats for the unleaded fuel. Again all the transmission internals were in great shape, so all it got was new bands, seals and gaskets. The similar Lincoln and Mercury Turnpike Cruiser 368 V8 was also a good engine. The only reason it was replaced was because of it had run it's course, plus the cubic inch and horsepower race was full blown. The "Y" blocks came to an end and the 292 was probably used last in the Ford F-100 pick-up. Many are still on the road due to the interest in early-60's Ford pick-ups. Ford needed a physically smaller engine to fit into the smaller cars at the dawn of the new compacts. Chevy already had the smallblock and Chrysler came up with the new LA engines, Ford followed suit. The new 260 Ford V8 showed-up in Fords compact cars first. It was also the first engine used in the Cobras and Sunbeam Tigers. Because it could hold it's own, it replaced the old 292 "Y" blocks. In 1965, it grew to 289 c.i. and then went into most Ford and Mercury's as their base V8 engine, including full-sized cars and pick-ups. The next generation brought the legendary 302 V8. I believe that Ford still manufactures them, but they were replaced by Ford's modular OHC engines. No. The "Y" block was a legendary and excellent engine. It was only hampered by physical dimensions and dated technology. Oh, the "flathead" Ford V8's can easily be modified to give reliable 210-250 horsepower. There is nothing like the exhaust note of a "flathead". Be sure to congratulate a person who has a vintage Ford with atleast a genuine Ford powertrain!

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    Ford replaced there Y series engines because they realized they had two problems they didn't like. First was both the Lincoln and Ford Y engines had two center exhaust valves close together this caused burned valves from over heating under extrema conditions. The second was the distributor was at the rear of the engine making it hard to service. Ford never made another North American engine with this problem again. Chevy built there engine for nearly 50 years and never fixed ether problem.

  • @automatedelectronics6062

    @automatedelectronics6062

    2 жыл бұрын

    @@mylanmiller9656 The rear distributor wasn't really a problem as many other engines from Mopar and several GM engines had them and never changed it either. I never had a problem servicing a "Y" block distributor. I hadn't seen any more valve problems with the "Y" blocks than any other engine in over 40 years of working on them. The Chevy smallblock always had inherent problems and culminated with the Siamese cylinders of the SB 400. I can't tell you how many SB's I've seen with holes in the sides of the blocks from thrown rods. They finally addressed the problems when they introduced the LS series.

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    @@automatedelectronics6062 The rear distributor was a problem for the Ford engineers and they did fix it. Just because Dodge and GM never addressed it or the two different

  • @automatedelectronics6062

    @automatedelectronics6062

    2 жыл бұрын

    @@mylanmiller9656 Ford engineers did the best they could. Heck, even on the old flathead V8's. They had the distributor originally mounted on the front of the engines and then changed it to the top of the engine. With the new "Y" blocks, Ford went to using a single water pump, compared to the 2 water pumps on the flatheads. They put the distributors in the back and they didn't interfere with the cooling systems as front mounted ones did. Plus there was more room for accessories on the front. The rear mounted distributors were easy to work on on the "Y" blocks, especially considering front-mounted accessories and easier for the cams to drive them. This I know from personal experience working on them. How many have you worked on? On Pontiac and Olds, the rear distributors we're a real pain because they were buried behind the intake manifold.

  • @mylanmiller9656

    @mylanmiller9656

    2 жыл бұрын

    @@automatedelectronics6062You should preach to the engineer's that changed them not me! As for working on them I never took the time to count how many Y blocks I worked on. I worked in a service station when I was going to school, changed the Points in lots of Y blocks and will never say they are good to work on. Compared to the FE or 289 they sucked.

  • @wysetech2000
    @wysetech20002 жыл бұрын

    My dad had a 1955 mercury with a 292. He bought it new and in a short time became very noisy. Turned out that it had the cam bearing problem you mentioned. They replaced the engine and it had well over 100.000 miles on it when he sold it. Other than a lot of blow by, it still ran like new.

  • @sking2173

    @sking2173

    2 жыл бұрын

    On a cold day, a three-year old Y-block blows more vapor from the crankcase vent tube than from the tailpipe !!

  • @samwalker7821

    @samwalker7821

    2 жыл бұрын

    My Dad had the same problem with his 55' Merc 292. He said he wished he had kept his old 51 Ford flat head. lol

  • @markbehr88
    @markbehr882 жыл бұрын

    Thanks for the tip. I am having my 272 V8 rebuilt in my 57 F250 so will talk to the builder about this.

  • @RareClassicCars

    @RareClassicCars

    2 жыл бұрын

    Good luck. If done well and regularly serviced, they can be good engines.

  • @markbehr88

    @markbehr88

    2 жыл бұрын

    @@RareClassicCars Thanks Adam. You can see it on my channel. It is a major project but I wanted to save it. Cheers Mark

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    Make sure he plugs the oil bypass hole in each rocker shaft. The 57 camshaft has a groove in the center journal, so that won't be an issue.

  • @markbehr88

    @markbehr88

    2 жыл бұрын

    Thanks Michael. I will.

  • @UberLummox
    @UberLummox2 жыл бұрын

    A mentor of mine used to street race (and track?) a 292 Y in a '62 Galaxie. He never said anything about the mill, but he said he went through many standard transmissions. He was a pretty serious racer. In '74 he found a '70 Cougar Eliminator he still has I think. Started w/the orig. Cleavland then later went to a monstrous 460 w/Chrysler 440 rods. It lifts the front off the ground by about a foot. Enough about me...GREAT video!

  • @johnjohnsn7633

    @johnjohnsn7633

    4 ай бұрын

    Those transmissions were Borg-Warner T-86s, and they were weak, unlike their older "brothers", the T-85, on which the T-10 4-Speed was based.

  • @UberLummox

    @UberLummox

    4 ай бұрын

    @@johnjohnsn7633 Ok thanks!

  • @montymatilda
    @montymatilda2 жыл бұрын

    Another great history video. My experience with the Y-Block engine was when I was running and detailing cars on a small car lot in the 'late '60s. We had a couple, maybe three of these engines come in various Fords that had the oiling problem. At the time and the condition of each of the cars, nothing was done and they were sold as is. Sure interesting to look at a cylinder head that had no oil on it. It is beyond me why Ford dumped the 332 FE motor that was only out for '58 & '59. That would have been a much better engine that the 292 they kept until 1964. More torque and power and quiet. They could have even kept the Y-Block 312 instead of the 292. I drove some 292's and 312's. The 312 was far superior in every way. Or even the Lincoln 317 to have a smaller V8 heading into the '60s. The 292 was a powerless gas hog. I drove a 352-2bbl '62 Ford Galaxie and that was far better than the Y-Block and more economical in the real world that I drove in. Ford had many mistakes that kept them in the number 2 position and this IMO was one of them. Who would want a 1961 Mercury Monterey with a 292, not me.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    In the 50s, the 292 was pretty potent, but in 58 they started detuning every year, so by 62 it made only 170 horses. In 57 it made 212 horsepower. That's a pretty big drop.

  • @montymatilda

    @montymatilda

    2 жыл бұрын

    @@michaelbenardo5695 True. Ford was looking for economy beginning in1959, even the Lincoln 430 dropped from 350hp down to 315 by 1960. Then they had to start increasing hp beginning in 61 for the new Continental. Having driven the 292, 312, 332 & 352 of that era, I really didn't like the 292. For whatever reason Ford reduced the power for was a silly thing to do, IMO. What about a very nice and quiet 332? My grandmother had a 59 Fairlane 500 with it and it was a great engine at 225hp. My 63 Impala had a 283 that made 20 more horsepower than your stated 170 in 62 and was quieter and smoother than the 292. My experiences were not good with the 292. IMO Ford made a mistake by not staying with the 332 FE. My experiences with the FE and MELs were great, all the way to the 428 FE and 462 MEL.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@montymatilda They did bring it back for trucks for I think 2 years. The 352 was a stroked 332. 3.5 inch stroke vs 3.3 inch stroke. I thought the 62 Chevy 283 was also down to 170, unlike the 61, which was 185 2 barrel, 230 4 barrel.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@montymatilda I think the 61 had just 300 horses. The 63 brought back the 4 barrel carb, but never again would we see the 350 - 375 of the late 50s.

  • @johnz8210
    @johnz82102 жыл бұрын

    That was good. Thanks to KZread and if anybody remembers the movie "It's a mad mad mad mad world", the engine on the chain hoist that Jonathan Winters smashed through the garage door of that service station he destroyed was a Y block.

  • @richmcintyre1178
    @richmcintyre11782 жыл бұрын

    My grandfather gave me my first car a 1955 Ford Customline 2 door. It had the BIG 292 V8 that ran on 6 cylinders most of the time. Grandpop didn't think his "new car" had an oil filter so he never changed it??? God, I loved that man 😀 The first time I removed the oil filter I think it weighed 15 pounds LOL. Being a budding gear head I rebuilt the motor and it ran great, with lots & lots of torque.

  • @Jurgy777
    @Jurgy7773 ай бұрын

    Built a y block 312 few years back, converted the rocker shaft assembly to full pressure setup. Lots of parts from Mummert's - was really happy with how it turned out.

  • @daveallen8824
    @daveallen88242 жыл бұрын

    And the have those lovely mushroom lifters...

  • @oceanmariner
    @oceanmariner2 жыл бұрын

    I had a 292 back in the day. My dad was a Ford guy. In those days engine rings only lasted about 80,000 miles. Getting 100,000 was considered a feat. Rebuilding engines was common. During this time I remember Ford's reputation for reliability was poor. Not only did the 292 engine need overhead oilers, but the shaft from the distributor that drove the oil pump had a tendency to break. My 292 thru a rod. I was so impressed with ford, I didn't have another for 50 years.

  • @machintelligence

    @machintelligence

    10 ай бұрын

    I had one that didn't break the intermediate shaft, but it did round off and quit driving the oil pump. I replaced it and drove the truck for several more years.

  • @lelandcarlson1668
    @lelandcarlson16683 ай бұрын

    I had a 1961 Ford Falcon with the 144 cid straight six that my grandfather originally purchased. It had the same issue with upper engine lubrication. My grandfather used non-detergent oil for the 10 years he owned it and the oil passage to the rocker arms was completely blocked. The crankcase was also full of sludge from the non-detergent motor oil. I remember my Dad putting some kerosene in the crankcase and running the engine up to temperature, then draining the oil. It came out in lumps. But to Ford's credit that little motor never left me stranded.

  • @Bobbygale121
    @Bobbygale1212 жыл бұрын

    My Dad was a construction equipment mechanic and had the opportunity to buy a 1954 F-100 ford pickup with the 239 V-8 and a trashed ford-a-Matic transmission from his employer for $100.00. The pickup had been sitting out in the yard for a few years and those old-time mechanics were beyond petrified of anything with an automatic transmission. A few of those old boys found a transmission in one of the sheds that would bolt up and Dad bought the non-synchromesh tranny for real cheap and installed it. Sold the pickup to my oldest brother for $100.00 -- My oldest brother spray painted it outside on a nearly windless day (Turned out surprisingly well.) After a few years, my next older brother bought it for $100.00 and drove it for a year or so. A few years later I bought it for $100.00 and learned to drive that transmission with no synchromesh. I left the pickup in my Dad's driveway when I joined the Marines in 1966 and he sold it for $50.00 lol. We never had any problems with the engine, but we always kept up on the proper oil changes. Driving a pickup with a non-syncromesh transmission is let's say.. A challenge.

  • @Paramount531
    @Paramount5312 жыл бұрын

    To be fair, Ford came very close to ditching their V8 altogether, a last minute decision spared it. Imagine the disaster that would have ensued if they had been stupid enough to actually not have a V8 only to be completely slaughtered by Chevrolet in 1955. Maybe a bad V8 was better than no V8. Even as a child, I hated the sound of the Y-block and its whiny starter. I loved the FE block, when tuned it was a really sweet engine.

  • @ladamyre1

    @ladamyre1

    2 жыл бұрын

    Especially that long stroke 428. MY brother-in-law had a 428 SCJ (medium riser heads) in a '67 Fairlane that the clutch safety switch had been by-passed on. It had a close ratio top-loader 4 speed in it with a 3.55 gear in the axle. One winter morning he asked sis to go crank it up to warm it up for him. He had left it in first gear and it was parked about 2 feet away from the block house wall. She had never driven it before and got in it, and turned the key without engaging the clutch!?! It fired up, ran into the wall, and sat there, still running, chirping the tires with the firing of every cylinder. lol! I once tried to outrun him on a Kawasaki 750 three cylinder 2 stroke, which was a "superbike" in those days. I ran off real fast, wrapped myself around the bike and buried the speedometer, 10 or 15 MPH past the 135 top scale and pegged to the stop inside the gauge. After about ten seconds he came around me about 10-15 mph faster in that Fairlane! That 428 was a real beast.

  • @thecollectoronthecorner7061

    @thecollectoronthecorner7061

    2 жыл бұрын

    Yes they used that long snout starter that engaged from behind the flywheel until 64.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    I have heard that too. Would have been pretty stupid, as most Ford buyers did not want a 6. They wanted a V8.

  • @wymple09
    @wymple092 жыл бұрын

    You have to go thru about 5 flatheads to find 1that doesn't have a cracked block somewhere. That's 1 of the 2 or 3 big reasons why the hotrodding community kicked it to the curb for the SBC.

  • @sking2173

    @sking2173

    2 жыл бұрын

    That, plus the old flathead couldn’t breathe at all ... A Briggs & Stratton mower engine has better exhaust scavenging ...

  • @jimbo3214
    @jimbo32142 жыл бұрын

    Adam what was the deal with the exhaust going along the front of the engine on some Y blocks?

  • @midnightgambler3718

    @midnightgambler3718

    2 жыл бұрын

    packaging and Ford being cheap

  • @TheCatOfAges

    @TheCatOfAges

    2 жыл бұрын

    Trucks did it to keep the engine hot

  • @DanEBoyd

    @DanEBoyd

    2 жыл бұрын

    I've noticed that too!! Wasn't that seen more in trucks than in passenger cars? I suspect it was done to make room for clutch linkage/Z-bars, and perhaps to keep that intense heat away from brake master cylinder and its mainline. And also maybe for hydraulic clutches which I suspect they were using in trucks back then. It probably kept heat from the driver's toe-board too.

  • @hendo337

    @hendo337

    2 жыл бұрын

    Does away with the need for a Y Pipe, flat heads had that too.

  • @davidpowell3347

    @davidpowell3347

    2 жыл бұрын

    A last minute cheap out to use single exhaust when the car was intended to use dual exhaust? (Just asking)

  • @garystanton1483
    @garystanton14839 ай бұрын

    The problem is you were not there in the 1950's. The Y-block was the first low cost overhead valve V8 that could be purchased on an average budget. Viewed with today's technology it might look bad. In the 1950's compared with other engines, it was a fantastic engine. I had a 57 with a 312. There wasn't hardly anything in stock form that didn't watch my tail lights.

  • @sking2173
    @sking21732 жыл бұрын

    Ford survived the late 50’s because of the aesthetic appeal of their cars, not their build quality or design excellence. The introduction of the FE engine also helped drag Ford into the 60’s in one piece.

  • @timothykeith1367
    @timothykeith13672 жыл бұрын

    Many still love the Y block, has nostalgia appeal. Y block is mostly bad because the Chevy small block was so good. I think Ford, being the v8 experts, was suprised at the success of the SBC, but new Fords didn't exactly linger on the dealer lots, so Ford kept producing the Y block to amortize the tooling.

  • @jimherman859

    @jimherman859

    2 жыл бұрын

    Timothy Keith yes the Chevy small block was perfect if you enjoyed cracked heads.

  • @johnsalvaterra1355

    @johnsalvaterra1355

    2 жыл бұрын

    The first SBC had its problems as well. Rocker arms, burning up. Using oil early, but eventually they got it straightened out.

  • @timothykeith1367

    @timothykeith1367

    2 жыл бұрын

    @@jimherman859 Stayed in production for decades. The 4.3 v,6 version remained in production until 2013

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    They fixed the rocker oiling problem early on. After that, it was fine.

  • @TheCatOfAges

    @TheCatOfAges

    Жыл бұрын

    The 55 sbc was a shitty motor. No ifs ands or buts. No oil filter, etc. Not a good motor

  • @Bbbbad724
    @Bbbbad724 Жыл бұрын

    The 317 Y block came out in 1952 and topped out with the 368 Turnpike Cruiser. I was a kid replacing the Y block with a 368. It came with 3 2V cars, and we changed the intake and in a 57 Ford 2 dr HT. It was FLMs first OHV, and were used in trucks for the N series until 1964 I believe. You could shave the heads and they had surprisingly good ports. The oddness of the Y block is unexplainable. The 368 when worked on it was wow!

  • @alanchidley2745
    @alanchidley27452 жыл бұрын

    Very well done content. Thank you.

  • @alvinprettyman1802
    @alvinprettyman18022 жыл бұрын

    thanks for the history lesson

  • @msbae
    @msbae2 жыл бұрын

    Seems Ford has a LOT of trouble with keeping their engines properly oiled... This motor, the early FE's, that 3-valve Triton motor in the 2004-08 F-Series trucks... How does Ford keep making that mistake?

  • @stewartgregory3364

    @stewartgregory3364

    2 жыл бұрын

    Ford has a long & proud tradition of making the same mistake over & over. Look no further then the power steering issues with the Exploder

  • @donreinke5863

    @donreinke5863

    2 жыл бұрын

    The early FE only had issues when used for racing as it did not have direct oil feed to the crankshaft bearings. That is why the side oiler 427 was made, the main oil galley directly fed the mains first, after early 427s in 1963 blew up on tracks.

  • @DanEBoyd

    @DanEBoyd

    2 жыл бұрын

    Ford also loves under-carbureting, coupled with intake manifolds which just aren't trying...

  • @sking2173

    @sking2173

    2 жыл бұрын

    @@mikec9112 - The 335 series wasn’t really a “top-oiler” like the FE-series engines. The FE engines (except the side-oiler) fed oil to the cam bearings, where it was then routed to the crank. The 335 routed oil first to the crank, and from there to the cam bearings. The 335 worked great on the street. The 335 did feed the mains off the lifter oil galleys, instead of having a dedicated galley for the crank. In racing applications, measures were taken to apportion a greater amount of the lifter-galley oil to the crank.

  • @brocluno01
    @brocluno012 жыл бұрын

    Old guy here who played with a lot of Y-Blocks back in the day. Biggest drawback was the stacked port arrangement and weight. The heads just did not flow as well as the SBC. Oiling was only a problem if your engine builder screwed up and did not clock the bearings correctly ... Up through 292, they had forged cranks and could handle big power increases like blowers. But all the good parts came from the marine industry. Crusader and Interceptor had aluminum timing covers, better intakes, and good cams. Isky made the best valve train parts. You are partially wrong about lasting a long time. The tooling was shipped to Ford South America (Brasil) and the engine was continually developed up to vertical port heads, etc. Now days all the best parts for Y blocks come from South America via the aftermarket as so many of these engines are still running (and racing) down there.

  • @sking2173

    @sking2173

    2 жыл бұрын

    The South American versions of the Y-block obviously share little in common with the Y-block junk Ford was producing in the late 50’s in the US ...

  • @subarutruck1
    @subarutruck1 Жыл бұрын

    Great info! I have 1957 Ford Fairlane 500 with 292. Lubrication issue. No oil going to left side of engine. Thanks for help!

  • @zeon5323
    @zeon53232 жыл бұрын

    I installed many external oiling fits back in the day. I kept telling customers with these cars they needed to change oil more often, but they never did. They came back for the external kit.

  • @MostlyBuicks

    @MostlyBuicks

    2 жыл бұрын

    Yes, for some reason people just don't want to change oil in their cars to this day.

  • @garymckee448

    @garymckee448

    2 жыл бұрын

    @jdslyman You got that right on a 3.6 G.M., I had one in a 06 Buick that loved oil.

  • @michaelf.2449

    @michaelf.2449

    2 жыл бұрын

    @jdslyman yeah if he did any engines from the 2000's it wouldn't be a hard content for Ford the obvious answer is the 3 valve motors. If he wanted to go with a Diesel the 6.0 would be the engine that takes the cake it basically bankrupted some small businesses

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @@MostlyBuicks That is something I never could understand. They are just too f-----g stubborn I guess.

  • @michaelbenardo5695

    @michaelbenardo5695

    2 жыл бұрын

    @jdslyman I don't know why they replaced the superb Buick V6 with that 3.6 engine.

  • @rightlanehog3151
    @rightlanehog31512 жыл бұрын

    Adam, I think you are firing out the videos this weekend just to keep yourself warm. 😉

  • @scottvincent7666
    @scottvincent7666 Жыл бұрын

    I owned a 64 pickup w/292. Ran great. Hauled a lot of firewood and pulled a loaded trailer often. Sweet old truck that I enjoyed. I seen many with the rocker oiling kits but mine didn’t need it. I ran 10w40 valvoline. It did leak but not “terrible”.

  • @sufferedenuf

    @sufferedenuf

    10 ай бұрын

    Sounds like I bought your old truck or one like it. Running strong, lots of torque, quiet and reliable. I am getting rid of my newer vehicles and going back to reliable carb powered, non electronic stuff that I can tune myself.

  • @jaymichaels5187
    @jaymichaels51872 жыл бұрын

    Ford's early OHV sixes were not so great in rocker arms lubrication either, it seems Ford over-engineered many aspects of these 1950s engines but failed on the sundry aspects of them.

  • @jamesfrench7299

    @jamesfrench7299

    2 жыл бұрын

    So if you sort those out with fixes, careful assembly and detergent oil, and don't skip changes, they were outstanding engines then.

  • @jaymichaels5187

    @jaymichaels5187

    2 жыл бұрын

    @@jamesfrench7299 Ford made the inline sixes much better later on. The Ford 300 cu inch six was legendary but in the 1950s I would have went for a Chevy inline six, as they been making those since the late 1920s for OHV inline sixes .

  • @jamesfrench7299

    @jamesfrench7299

    2 жыл бұрын

    @@jaymichaels5187 Ford Australia developed the Barra six from the parameters of the six in the 1960 Falcon compact. It just kept evolving after they developed a whole new engine with single overhead cam in 1988 with the same bore centres to the monster we got when they introduced DOHC and a turbo option in 2003 and gradually improved more until it's demise in 2016. I have heard about your 300ci six. Very well regarded.

  • @jaymichaels5187

    @jaymichaels5187

    2 жыл бұрын

    @@jamesfrench7299 The Ford 300 cu. inch six was a fantastic engine, thirsty yes but very reliable and very torque-ee. Two other great inline sixes were the AMC 258 and the Plymouth/Dodge slant six up to 225 cu in. I had both sixes, the AMC one was great in extreme cold weather starting in northern Canada with a good battery and had great torque too, this evolved to the famous Jeep 4 litre inline six. The slant six was not as good for torque but very reliable and great for putting a lot of miles on it with no problems and could take a lot of abuse and maintenance neglect.

  • @jamesfrench7299

    @jamesfrench7299

    2 жыл бұрын

    @@jaymichaels5187 my dad had a 1964 Australian Valiant known as the AP5 model which had the 225 slant and push button selector Torqueflite. It outclassed the Ford and GM Holden sixes for HP. Very smooth and modern sounding motor too. I thought that 258 AMC would be the ancestor of the well regarded Jeep motor before reading on. Chrysler Australia had the 245 and 265 Hemi inline six motor which succeeded the Slant 225 in the Aussie market in 1970. Very similar to the Jeep engine. More of a peaky motor and a bit coarse at higher revs bit internally efficient. Achieved very good mileage when they fitted Chrysler's electronic lean burn system to them -while they worked properly! The hemi six was originally being developed for trucks in America before it was canned there and adopted in Australia for our Valiant cars!

Келесі