What should I use for removing rust???
Автокөліктер мен көлік құралдары
You have lots of options when tackling rust - Dave is walking through the differences between Fast Etch, Rust Converter, and Gel Rust Dissolver.
Fast Etch: www.eastwood.com/rust-remover...
Gel Dissolver: www.eastwood.com/rust-remover...
Rust Converter: www.eastwood.com/eastwood-rus...
00:00 Introduction
01:52 Fast Etch
05:25 Rust Converter
08:13 Rust Dissolver
11:43 Where to Apply
Eastwood Fast Etch
This specially formulated rust remover is a powerful, rust-fighting liquid created to meet the needs of auto restorers.
✅ Ideal Prep for Painting and Powder Coating
✅ Leaves Zinc Phosphate Coating
✅ Promotes Adhesion and Prevents Rust
✅ It reaches even inaccessible areas, quickly dissolving iron oxide completely and leaving a zinc phosphate coating.
✅ Fast Etch can be sprayed, brushed, or used as a parts dip.
✅ It is non-toxic, non-flammable and reusable.
Treated surfaces should be wiped with PRE Painting Prep (10041 Z) or thinner before priming and painting. Only the quart size comes with a sprayer.
Gel Rust Dissolver
Even the oldest, rustiest metal parts can be restored by using our automotive rust removal solution. Eastwood Rust Dissolver removes only the rust and won't eat away at the metal itself. This leaves the newly de-rusted metal ready to paint, plate or powder-coat. Our rust remover outperforms many comparable products such as Rust-oleum while costing less, letting you renew body panels, engine blocks, springs, tubes and much more.
Liquid Rust Dissolver works as long as the surface is wet. Simply submerge the part let it sit for at least eight hours. Items that cannot be fully immersed due to size can be placed in the discharge stream of a commonly available small pump. Another option is to apply our Rust Remover Gel to the surface, then loosely cover the part in plastic or saran wrap for protection. One gallon of liquid or gel de-rusts about 20 square feet of metal. Once you’re finished with the rust dissolver, wipe the surface down with Eastwood PRE Painting Prep to remove any remaining loose rust. Learn more about our rust removal solutions at the Eastwood Garage.
Eastwood Rust Dissolver Features:
✅ Gentle enough for engine parts
✅ Reusable
✅ Removes about 5 sq. ft. of rust per quart
Rust Converter
Instead of throwing out rusted automotive parts that you know will be hard to replace, use Eastwood Rust Converter to restore their performance. This acidic paint is formulated for panels and parts that have heavier rust but still are structurally intact. By spraying or brushing Rust Converter on the surface, you trigger a chemical reaction that turn residual rust into more stable iron oxide. It also forms a paintable black protective coating that is compatible with most topcoats. Last but not least, Rust Converter seals the metal to help prevent future corrosion.
Use rust converting treatment as part of a complete restoration process that gets your barn find back on the road. Our formula penetrates the metal quickly and doesn’t require any sanding. Since the paint is water-based, it’s much safer than traditional solvents. The Eastwood Garage has much more information about Rust Converter, including when to use it versus other anti-rust solutions (such as Rust Encapsulator ). Extend the life of your vehicle by doing the job right with a 100% customer satisfaction guarantee.
✅ Rust Converter stops residual rust, and turns it into a black, protective, ready-to-paint coating, without sanding. Just apply to transform the rust
✅ Penetrates faster than other brands
✅ No sanding needed - just apply to transform rust
✅ Coverage: 50 square feet per quart
✅ No mixing needed
✅ 90 Day Warrant
For more information on Eastwood products visit www.eastwood.com or stay connected with the team via:
Facebook - / eastwoodcompany
Instagram - / eastwoodco
Eastwood has everything you need to do the job right when you're restoring a car, truck or motorcycle - from welders to paint and everything in between.
Пікірлер: 31
Fast Etch: www.eastwood.com/rust-remover-eastwood-fast-etch.html?KZread&+comparison+fast+etch Gel Dissolver: www.eastwood.com/rust-remover-eastwood-rust-dissolver.html?KZread&+comparison+gel+dissolver Rust Converter: www.eastwood.com/eastwood-rust-converter.html?KZread&+converter+gel+dissolver
Excellent comparison of these three products.
So far I find the fast etch to be very effective and it suffers virtually no flash rusting, the only side effect is you have to wipe out the excess before it get dry or it will leave gummy residue. Heavily rusted metal requires some wire brushing or these chemicals will not able to penetrate.
I had bought some of each based on the amount of work I'm doing on my car. Can't wait to try them out.
@eastwoodco
4 ай бұрын
Let us know what you think!
I have a rust spot on the lower fender of my daily driver that keeps coming back every winter. I've been using gel dissolver, etching primer and an enamel urethane top coat with no luck. I will use a rust encapsulater in the spring. Thanks for the tip!
@anah9288
14 күн бұрын
I’m hearing the rust belt uses a rust encapsulater after the other stuff. Etch, clean/prime, encapsulate, then put a wax based product on top every year, like Cosmoline. You can also do clear coat, but still have to use a fluid or wax film on top every year. I spend summers in Maine and never had to worry about rust til now. One summer and my van was aged over a decade! Going to be doing the series I said on the whole undercarriage. Prob one section at a time, cause it’s a lot and gonna take a while. It’ll be worth it though!
I use it on my 56 , 63 f100 and 51f3 it work great , east wood has great product! Thank you.
@eastwoodco
2 ай бұрын
Please leave us a review on the product page! We'd love to have your feedback. Fast Etch: www.eastwood.com/rust-remover-eastwood-fast-etch.html Rust Dissolver: www.eastwood.com/rust-remover-eastwood-rust-dissolver.html Rust Converter: www.eastwood.com/eastwood-rust-converter.html
Fantastic video!
@eastwoodco
4 ай бұрын
Glad you liked it!
Is the rust dissolver basically the same chemical as fast etch, but in gel form?
@levih.4252
2 ай бұрын
Eastwood, same question.... (not necessarily the same chemical but the same result?)
Will there be any other flavors in the future?
Please tell us the active ingredients of the last two. Phosphoric acid was the fast etch. Then what are the next two? Is one of them Lye like found in RUST OUT?
Awesome video
@eastwoodco
4 ай бұрын
Thanks!
What’s the stuff in the can that he using after apply the fast etch in the first demonstration
@eastwoodco
16 күн бұрын
After Fast Etch, he applies Pre-Painting Prep to neutralize the fast etch, and clean off the panel www.eastwood.com/ew-pre-painting-prep-aerosol-11oz.html
Fast etch...so acetone neutralizes?
@eastwoodco
2 ай бұрын
Yes.
is it ok to spray eastwood fast etch near hydraulic hose?
@eastwoodco
Күн бұрын
You will probably want to tape it off, and wipe any excess spray off with pre-painting prep to neutralize it.
I want to let my parts set for a year before I paint. Will fast etch stop them from flash rusting if I keep them in dry storage?
@eastwoodco
2 ай бұрын
That's not what it's designed to do, we recommend putting the parts in primer at least if they're going to sit.
@Rottingboards
2 ай бұрын
Thanks for the quick replies. You products are top notch! @@eastwoodco
That's good
9:00 that's the thinnest gel I've ever seen!
FYI with the liquid rust dissolver, do not leave any metal part in this liquid over 24-36 hours especially thin metal parts because this chemical will dissolve more than just rust. I had left bolts, screws, clips and even sockets submerged in this chemical for over two days to remove all the rust off and everything looked like the aftermath of metal spoons used to mix caustic chemicals in cartoons! I’ll be the first to say the product works, but definitely a little too well so whatever item being covered in this chemical needs to be checked every few hours to monitor progress. Also if the part is cleaned with hot water, it must be forced air dried immediately along with coated with a chemical such as metal wash to prevent flash rust from forming.
Dude, do you know how many morons are going to use this stuff outside on a windy day! Mask and eye protection is a must anytime you are working with chemicals. Just saying, great products and great video. Thanks for posting.
@eastwoodco
3 ай бұрын
We totally agree PPE is a must, that's why Dave has his safety glasses on when spraying the fast etch and gloves on throughout.