If you've not used Ditra or an uncoupling membrane before don't try and lay tiles the same day. Use Rapid Set adhesive to fix the ditra to the floor and always leave it overnight. Tat way if you have to lift a tile you won't pull the mat up with it :)

@MrBugs183

Жыл бұрын

@@ks13077 I do this for a living and I see stupid new products all the time, but uncoupling is certainly necessary for tiling over wooden floors and underfloor heated screeds. It’s super easy to lay, so it is heard to make a mistake.

@vapeurdepisse

11 ай бұрын

But Hardie Backer had worked great for decades and it's screwed down into the floor, so it's even more secure.

@MrBugs183

11 ай бұрын

@@vapeurdepisse all depends on the situation. You can’t screw hardi over an under floor heated screed or screw into a floor of unknown depths with screws. Ditra goes on without penetration of the floor. Both work well, just depends on what it has to do.

@annakissed3226

7 ай бұрын

Matt have you never seen Holmes on Homes? From the late nineties in Canada Practically every show they are rebuilding a bathroom or kitchen & using Shulter products to lay tile!

@Daniel-wd4jg

5 ай бұрын

Great product... factory certified in Reno facility.

Be warned, this stuff SIGNIFICANTLY increased mortar cure time for me (concrete slab, with large sized tiles), it doesn’t allow the moisture to leech and evaporate the same way backer board does. It was three days before I could put weight on the tiles to grout. I still like the low profile and ease of install-just plan your job accordingly.

@deeznutt666

2 жыл бұрын

same here i got thick larger sized tiles & dunno if i should get the stuff in the video for it or no when installing its not for bathroom its for open kitchen floor

@vitaliypro8441

2 жыл бұрын

Mortar will set and cure even if completely submerged in water, unless you added too much water to your mix in the first place it shouldn’t SIGNIFICANTLY increase cure time, unless you are confusing curing process with drying

@JB-uh6dg

2 жыл бұрын

@@vitaliypro8441 Nope, thats not it.

@billjohnson7347

2 жыл бұрын

What thinset did you use?

@Wolf-rg7ih

2 жыл бұрын

@@deeznutt666 have you ended up using this product in ur kitchen ? I’m doing a main walkways and it is. Plywood subfloor. Kind confused. Of What I should use. Hardiebacker or. This rolls

Wow! Absolutely brilliant. Provides answers to a whole array of issues I have with kitchen, bathroom and other indoor tiled areas of the house. Very informative. Thanks for sharing.

I have specified this product for many years and it has never failed. I first used it 20 years ago in two office block foyers where the contractor had laid tiles direct on the concrete floor that had subsequently cracked along joint lines in the substrate below. The installation allowed the contractor to retile the floor as originally specified that was now fully reliable and without having to rebuild the foyer floors to cure inherent problems. I have since spec'd this below all wet tile areas and in location where the substrate was variable, irrespective of where a finishing screed was laid on top. I have had no reported tile failures of any sort.

Your character, wisdom, and presentation is the best I've witnessed in a long time. You deserve the best!!!

@mr.doctorcaptain1124

Ай бұрын

Are you this guys mom or something lol. But in all seriousness it is a helpful video

Nice job! Very informative. My husband suggested I view this since he is interested in using ICF for our new house construction. I liked the way you; broke down terms and made everything easy to understand. Your Pros and Cons were very helpful, since I too, had concerns about some of the issues you elaborated on.

im a Registered Nurse, dont know how i got here but it was very INFORMATIVE

@rubyruby6358

3 жыл бұрын

I work in HC as well. Have no clue how I got here but I know I want this under the tile in my new home!

@_ivaaannn

3 жыл бұрын

I'm watching this from the space station, idk how I got here but I didn't know I needed this info until I got the info

I used this on our bathroom remodel project a few years ago. What a great product! I will always use this for tile work moving forward.

@EPICSOUNDTRAX

Ай бұрын

Don't do that. This product is complete garbage Use MAPEI green mat way better than this junk. Your tiles will.pop out very soon. The only way to know the truth is if you demolish bathrooms and have tested both products This orange garbage fails all the time Shluter is a crappy company I will never use them in my life never They fail all the time. Try to pull tiles over green Mapei mat and see how it will go . You cannot remove them Over this pink garbage they pop out like nithing. Demolisued 3 bathrooms in one day Tried to demolish a bathroom with Mapei and could not go quarter in one day and need power tools Dont use this orange bs your tiles will crumble in a few years.

I used the Kerdi shower system with the square drain and fleece to build my shower system 8 years ago and its working perfect. I hired out the tile work and the guy loved working around the square drain instead of the round ones most people us. If I did it again I would for sure add heat to the shower floor and the bathroom floor. Its a great system.

Matt, I am actually doing my own shower remodel as well as the entire master bathroom. I'll be using Schluter's Kerdi system at least for the shower, which I'll be making a custom floor pan with Kerdi's drain as well. From what I've researched it is going to be a great option for our remodel. I'll try to get some photos and maybe a video of the remodel as we progress if your interested. Great product in my opinion. Your videos have definitely made me think more about the products I use in my DIY projects as well as what I'll be using should we decide to build our next home.

16years ago I put this product down along with a floor heating electric system in my house built in 1936. My tile has not cracked, moved and none of the grout has cracked. It stiffened the subfloor greatly but also allows the structure to move without damage to the floorI love Schluter my brother is a kitchen and bath designer and that'll those guys use for decades. Great product super easy to work with and super light THAT WORKS!!!

@anthonyman8008

2 жыл бұрын

❤

@thebobloblawshow8832

Жыл бұрын

It would have turned out the same without it. On top of concrete is it’s only use.

@thomassheridan4252

Жыл бұрын

@@thebobloblawshow8832 wrong,

@LincolnLog

Жыл бұрын

@@thebobloblawshow8832 I dont agree. Our stick home was built in 1999 and the bathroom grout is cracked or there are gaps between grout and the tile edge, decoupling membrane wasnt used over plywood subfloor. Now, it doesnt matter much to us because we dont care or observe too closely, but for sticklers and perfectionists they would want a reno

@thebobloblawshow8832

Жыл бұрын

@@LincolnLog well agree or not the proof is in the pudding. Never had an issue. Let me put it to you this way: what did people do before Schluter? Waste of money.

My mom mentioned this to me yesterday, I had no idea what she was talking about. KZread recommends this 1 year old video... They are always listening.

@MinnesotaBeekeeper

3 жыл бұрын

No shit. scary.

@johnniethepom2905

3 жыл бұрын

A sure sign Google Ads is picking up key words in your conversations !

@VeteranAviator

3 жыл бұрын

Just called my tile guy yesterday, video recommended this morning.

@coleswaggins

2 ай бұрын

I know how you feel. I've just recently wanted to do something with tiles and these vids pop up.

@mondavou9408

Ай бұрын

Don't let people tell you that you're crazy! You're not crazy for noticing it. They are crazy for NOT noticing and just want to protect their fragile ego. Tech in the wrong hands = bad, bad, bad.

Thank you. This is exactly what I wanted to know at 4am

I used to help my uncle lay mosaic tiling when I was in college. That was around 8-9 years ago. It’s to my understanding it’s code to use a product similar to float the floor. He used this product and I’m sure to this day still does. It’s brought back so many memories of painstaking hours of laying tile. It’s unbelievable how hard that work is and I have a great level of respect for the laborers that work with tile. My uncle is an artist and to watch him break pieces of tile and pick and choose what shapes to build a piece is amazing. Then to tie it into a floor is on another level. I’m glad I learned what I could with him. Thanks KZread for putting this in my recommendations. Great product and with my experience with it I give it a thumbs up.

@noelburke6224

Жыл бұрын

Well if you have great respect for them then stop calling them labourer they are skilled craftsmen

@HooningAroundLife

Жыл бұрын

I mean, I’d have to see the work before I go as far as calling anyone a skilled anything lol. If you’ve been in construction you know it’s a hit or miss with the contractors.

Thank you Sal. I am a professional who has been taught wrong. You have been amazing helping my understanding and quality.

I have used this product a few years ago out of interest, but now see how it can really be applied. Thank you for the video I now know what else I need to look out for.

I installed about 250k ft of tile over my career and I was very reluctant to start using these uncoupling mats. I've had very few issues with bond failure on my tile jobs,I have done repairs where the tile has come loose on the top half of the ditra mat. I have used uncoupling mats with the fleece on both sides,that's what I use now.

Did my master bath, with walk in shower (no curb) 7 years ago. With ditra, and kirdi awesome products. Their shower kits and drain assemblies are very well designed, be available here in Ontario Canada for over a decade, Mike Holmes has featured it on almost every build since it came available in north America

@EPICSOUNDTRAX

Ай бұрын

Also they are the products that will have hidden mold and rot and will never show These products are the worst products i have ever seen. My experience I had to renovate 4 bathrooms in one house and rip apart this company products On the surface everything was good under neat complete garbage Watch horror stories here on youtube All from this company products I am using MAPEI way better and professional This company y has good ideas but their products rot very easily.

Love this episode and product! Plan on using it in our newly remodeled bathrooms!

As part-time handyman and I have done a couple showers for others now using Schulter and was very happy with it. Now doing a whole master washroom reno for my wife and feeling confident using this product to tile over the wood floor. Cheers

I was surprised you didn’t make this video earlier. I have been using this product for years and the time saving will pay for the extra cost. You should also use the Kerdi product as well

Spectacular demonstration for an awesome and innovative product line. "Uncouple" is an appropriate verb for separating railroad cars, but the better engineering term would be "decouple."

Looks like a great product and will definitely use it in my future home build. Thanks!

Great job explaining Ditra and how to properly install it! Thanks for also sharing info on Schluter Systems Training Classes.

It's also good for heated floors. As an electrician we run our heating conductor in between the squares. It holds the conductor very well

@colerobinson1187

Жыл бұрын

that would be the ditra heat you are referring too! Same general look but denser and has grooves for heating wires!

Mike Holmes has been using this material for years in his remodels...great stuff. I wish I had known this product when I remodeled by bathrooms.

@EdgeLagerthaSeawolf

3 жыл бұрын

Love Mike Holmes he's one of the best and I wish more contractors took pride in their work and cared about their customers doing the job correctly the first time around.

Just finished a bathroom remodel on my 2nd floor main bath. Full tile tub surround and from the countertop down in the rest of the room. Looks fantastic. Installer used traditional methods. We talked about the Kerdi system and it’s benefits. He really wants to use it but the company he works for doesn’t use it, yet. So, fingers crossed it doesn’t fail. I may take on the downstairs bathroom myself with the kerdi. Looks so much easier than what had to be done upstairs for waterproofing.

DIYer here, and this is a great product. I need to remodel a bathroom and this is the way to go, thanks for the info.

I've used This product and absolutely Love it. Works great, as long as you do it as they have instructed. Do not try to cut corners with this product. Love it

KZread algorithms, we meet again

@hansols1727

3 жыл бұрын

Plot twist: Not this time

@Tre16

2 жыл бұрын

Is there anything original in that brain of yours instead of this constant copy and paste from you parrots?

@tomjohnable

2 жыл бұрын

@@Tre16 Is there anything original in that brain of yours instead of this constant copy and paste from you parrots?

@kenya91b

2 жыл бұрын

@@tomjohnable 😆

@Fx_-

2 жыл бұрын

Hello Clareese

Dude, I love your ending sign-off almost as much as your content 😄. Thanks for what your do!!

@MrGwizyadig

3 жыл бұрын

Don't forget "Let's get goinnn'!" at the intro

I have known about this stuff for about 10 years now. Super nice product. I love its versatility.

I removed one of these ditra systems and it was a nightmare wrestling match. Very strong install, surprised me and I've lots of demo experience.

@AFatalPapercut

6 ай бұрын

exactly....awesome for install,..but it's a complete pita to remove.

One aspect that really impressed me is that you can use this to create a full room shower without a barrier.. Can be really creative.

@jlanemiller

5 жыл бұрын

I have an 8 bathroom new construction house I'm doing and they will all have curbless barrier free showers

@megenberg8

5 жыл бұрын

@@jlanemiller totally!

@Panasyukvic

5 жыл бұрын

@@jlanemiller pictures or it didn't happen 😉

@jlanemiller

5 жыл бұрын

Panasyukvic I’ll keep you posted!

@Crazt

5 жыл бұрын

You should look into Japanese showers, these are found on middle class homes all over the country. It's how I plan on building a master bath in my forever home.

I love this product! especially the Ditra heat membrane

This product is awesome. Used it in the UK on my first tiling attempt in 1993. Works so well so come on USA try it

Used this product in upstairs master bathroom and was very pleased. One benefit Matt does not point out is sound dampening. Significantly lessens sound of footfalls on tile in downstair rooms.

@kentvolk9254

2 жыл бұрын

°°

Wonderful invention. *The floor is also warmer* with this type of insulation.

@jameselliott8541

5 жыл бұрын

That's heat cables. Somewhat different product. It looks more like lego studs with cable in between. Or it could be water pipes in the slab. Tile is as cold as my soul otherwise.

@RainCity3rd

5 жыл бұрын

Tile is always going to be cold unless you are piping hot water or electric heating pads under it. Great for hot weather though! Carpet nice soft and warm but not durable, and pain the keep clean.

I have used this many times, very good for large tiled areas where you want to avoid expansion joints. Never had any tile or grout line crack after using this even when pushing the area with continuous tile well past what would normally result in expansion cracks. Over underfloor heating this stuff is pretty much essential and works very well, I tiled a 150 square metre heated floor over 10 years ago with it and not a single crack in tile or grout in all that time.

@schrodingerscat1863

Жыл бұрын

@@private8559 Yes they do but in my experience using decoupling membrane this can be pushed well beyond the recommendations, that was my point. This is especially true for tiling over underfloor heating. The recommendations are very conservative.

@schrodingerscat1863

Жыл бұрын

@@private8559 For the most part pushing the boundaries comes from clients who are prepared to take the risk to avoid expansion joints. I have read the Schluter documentation together with Vario and Durabase which I also use. Its usually down to the type of tile being used and the type of floor how far I would be prepared to push it.

@christiann4635

7 ай бұрын

What type of thinnest did you use on top to lay the tile? Modified or unmodified?

@schrodingerscat1863

7 ай бұрын

@@christiann4635 Depends on the situation really, heated floors really always require flexible adhesive often the really flexible stuff which is expensive but cheaper than having to redo it when there are problems. Decoupling membranes really work best with the polymerised flexible adhesives anyway. I have found the fibre reinforced adhesives to be very good too where there is going to be excessive expansion.

@jmiller6180

3 ай бұрын

You mentioned goin over the heated mats with ditra ...What do you recommend using along side of the heated mats to make up the same height ? ( I plan on only doing 50% heat mat coverage on concrete slab)

Thank you for this (from Ontario, Canada). I’m retired & have worked on a number of tile projects over the past few years. I was looking for a system to reduce the thickness of tile install over plywood subfloor & still get good results without using concrete boards. Really enjoy your videos.

@dred05m61

2 жыл бұрын

Thank you for this great comment.

I don’t know if you have more online videos like this but you are the best teacher I have ever been able to actually watch online and learn better than I can when I’m on the site because I get yelled and bitched at. You’re calm you are very well spoken and you show an example As you were explaining yourself somebody is doing the background work at the same time. Brilliant. Please continue as this is something that I would definitely describe four or even sign up for for course. Learned on the job well, I can imagine you only understand better than I do these people we work for I just bitch and moan and call you names but don’t teach you. Thank you for doing this. God bless I hope your family is safe healthy and well.

I have used the Ditra underlayment, and will use it again because it does a great job of isolating the tile and saves space when you want to match levels with a hardwood floor. The adhesive thinset layer must be wet enough to adhere to the Ditra fleece backing, and this can be tricky, as is shown in the video. But the biggest surprise is how much mortar must be used to adhere the tile--about twice as much as with cement board.

@PeteNice29

7 ай бұрын

I'm assuming that's because a large percentage of the initial layer is filling the holes, thus not making contact with the back of the tile.

I've used all of their products, and it's an absolute pleasure to work with, and you end up with a bullet proof job.👏

Been using it for 25yrs now, can't beat it!

I'm in Arlington, TX ...I invested in an uncoupling membrane for my kitchen and bathroom tile install, 5 years ago. Best investment..my foundation has settled and repair has been done recently and no cracked tiles in the kitchen or bathroom. The installer definitely needs to install it correctly and use the correct mortar for the installation.

@QueOndaWhey

3 жыл бұрын

In North Dallas and all our kitchen tiles are cracking severely

@Nic2Blk

3 жыл бұрын

@@QueOndaWhey OH NO! Gosh do you have foundation issues? It sucks when stuff is moving and cracking around you lol. If that's not it, I know my best friend had cracked tiles because of bad installation..not enough mortar used when they were installed.

@slimdougmaddox4634

3 жыл бұрын

Hope yall alright down there. 🙏🏽

@smcewen7

3 жыл бұрын

If you have foundation issues its going to crack anyways.

@Nic2Blk

3 жыл бұрын

@@smcewen7 None of my tiles have cracked, but hey I can't speak for everyone's experience with the product.

Been using Ditra for years, including Ditra Heat, love it! Have also done a few showers using Kerdi and Kerdi Board, wouldn't do it any other way. Great system!

@Ckypwnd

4 жыл бұрын

steven kile 😂😂😂😂😂

@johnhender

4 жыл бұрын

Thats all we use. Most tradesmen don't do the training to understand the system. I use kerdi for al my repair jobs of the other so called superior systems, the more things change the more they stay the same- doing things the same old dumb ways and most guys don't even do it right the old way

I have specified Schluter systems many times over the last 10 years or so and it is my go to spec for any tiled areas irrespective of whether they are wet or not. In fact I was called to provide a rectification spec on two large office reception areas where the tiling had reflective cracking over concrete daywork joints. In both areas threats of consequential loss and disruption meant that the pressure was on to settle the issue once and for all. Schluter provided both the Ditra matting and the underfloor heating mat (check this out it is the best system I have seen) in the two areas.

@EPICSOUNDTRAX

Ай бұрын

Mapei is better This company is epic fail all the time. Will never use them in my life All their products are complete garbage You will find out when your cliets sew you in a few years and you cannot explain why all their oroducts failed. MAPEI is number one This company is a sham.

I’m a plumber in Dallas and I would love to do work for this man. He is all about the highest quality. I would love a chance to work for a residential contractor that has those standards. Most contractors have no interest in quality. They only want cheap. That’s why I quit the residential world and went the mechanical/industrial route where quality is still valued. He does amazing work.

@StarkillerObl

Жыл бұрын

I can appreciate the sentiment. I think that when the quality is high people can just go on with their lifes and create new things that give new value, but if the quality is low then there's this whole spiral of time wasting: - the customer notices the problem and has to call the person that has done it - Not always, but sometimes they will waste time arguing, because the company tries to avoid repairing it - Someone needs to come and repair it - Often someone on the side of the customer needs to spend time and "watch" the person repairing it (I think that 99% of people that would come to do the repair are decent and wouldn't steal anything even if they had a chance, but there's always this 1% that is less decent and also there's always this anxiety when You need to let a stranger into your house) All this is time wasted, and also there are other situations -> maybe the thing doesn't break, but is just slightly (but visibly) out of sync and then people are annoyed at that. More quality -> more time and energy to enjoy life and hopefully create more awesome things

@apatwella

2 ай бұрын

Do the contractors want cheap, or their customers?

@brasshouse9822

2 ай бұрын

@@apatwella most want cheap

Installed in my kitchen super easy great waterproofing!

@djtheg6819

4 жыл бұрын

It's not water proofing at all. It's a uncoupling membrane. Basically it's minimizes transfers of stresses from below it to prevent cracking through the thinset and ultimately the tile. If you think you have a water proof floor you are sadly mistaken. Infact we just redid 60 bathrooms at our commercial setting that used the product and it failed BECAUSE water would get trapped between the prodt and the thinset ultimately leading to it becoming saturated and holding the moisture and then uncoupling and then the problem just magnified as a small section broke down and would migrate eventually to large areas and then the product itself started degrading.

@TimothyRitzer

3 жыл бұрын

@@djtheg6819 He specifically talks about how it can be combined to be waterproof, and it is approved for use in showers. That isn't to say that it won't fail if left water saturated without proper drainage. But is that really worth talking about? No tile system handles being under water constantly without proper drainage...

@RedondoBeach2

3 жыл бұрын

@@djtheg6819 I appreciate hearing the negatives about this product based on your experience. Seems like you were pointing them out based on the original comment you replied to in this thread. Were you highlighting these issues to point out that there are negatives that people should be aware of but aren't completely against using the product, or are you completely against using the product? Also, you pointed out that trapped water was an issue. Would you say this was most likely the case because the product is poorly designed or because it was poorly installed? I have to believe the manufacturer took the potential for trapped water into consideration when designing the product and therefore most likely gives specific instructions on how to install it in order to avoid this issue. Is this not the case?

@1pecrnet

3 жыл бұрын

Does this help on uneven slab installs?

@xyzsame4081

3 жыл бұрын

@@TimothyRitzer I understood it is NOT the system for showers but for the occasional accidental spill (washing machine or kids making more of a wet mess than adults would to) it is fairly good.

A builder should always have every possible method in his arsenal. This system was covered by Holmes on Homes some time ago however it is nice to be reminded of it. As a decoupler, it may also be good under wood floors which are glued to a slab (only after a water seepage test has been performed and passed) to keep the boards from separating over time if a crack develops.

Matt this is an excellent video about ditra. I have used it for many years. Great video!

I’m surprised this video from just 10 months ago, I would have expected Matt would have been using this 10 years ago!!

Hay Matt, Excellent Video. When I was in Italy the house I was billeted in was an amazing structure hundreds of years old. This entire structure was masonry, with floors that had not cracked since originally built. What I witnessed amazed me and I couldn’t believe how simple and affective this method was. The tile floors where laid on sand. Like you said, uncoupled, when the building moves the floors just kind of vibrates sliding around. Crazy. Hope you have a Great New Year.

@SirenaSpades

3 жыл бұрын

The same reason you lay a foot or two of sand before pouring a concrete slab for a garage, or putting a down a sand pad for an above ground pool. It's effective.

@ericastier1646

14 күн бұрын

Sand is probably too heavy to be practical with today cheap wood stick carpentry used in america but i get the decoupling idea, that's great.

I live in Sweden and I am a carpenter and concrete does not crack if you do it right. If it cracks the problem is - to little rebar in the foundation - concrete dries to fast when it is "burning" - bad ground work under the foundations. happy building!

@marlonwood8952

5 жыл бұрын

Where he is in Texas most homes have tensioned concrete foundations that flex throughout the seasons on the first floor. It may go 3 months no rain on a clay ground, so the soil shrinks a lot. Hes talking about what he has to deal with

@SuperBardley

5 жыл бұрын

One of the most common causes of concrete cracking is excess water in the mix. This happens because wetter concrete is easier to work.

This is fantastic. Here in the UK people have little or no confidence in builders because they do everything as cheap as possible only to cause home owners additional costs to rectify shoddy workmanship. Just listening to you, give me confidence in this product (even though I am useless at DIY) to have it installed in my next home. Thank you

@agdgdgwngo

Жыл бұрын

We like to use stuff like because it means we don't have to fix cracked tiles all the time for free.

I remodeled 5 years ago and insisted on Kerdi in the shower and Ditra on the floor. Great system. To make it even better use Mapei Flexcolor CQ which is non porous grout and does not stain. Between ceramic tile and the Flexcolor CQ show dries bone dry in less than an hour. I have over 600sf of tile done with Flexcolor CQ .

These are great products, first found out about them from Mike Holmes, he has been using these for years. If it's Holmes approved then it's good for me.

I installed this because of the uncoupling. What I didn't expect was HOW MUCH BETTER my room felt after the install. I had zero insulation under my old faux hardwood floors. The ditra system made it so I can walk around barefoot in the winter in my own home again

@h2thechizoit445

2 ай бұрын

How did it feel better? From what I understand it's meant to make tile instalation better and last longer. So why would it make your room feel better if your not even walking on it

Very impressive and informative. Just bought a house with most of the bathroom custom tiled. I hope the person(s) used this in their install. Only time will tell as myself and the Mrs. use the bathroom. I'm now a sub!

I used it on a 3/4” plywood bath floor that I was trying to maintain the elevation going into an existing floor outside that bathroom, so I didn’t have the room to add 1/2” cement board. After a couple years and no cracks in my tile. That’s all I need for proof that this works...

Cool.. like the Penn and Teller of Construction/Installation :)

Hi Matt, I completely agree with you about the Schluter products. I used them on my concrete floor on grade about 10 years ago and I love it. I think at the time I felt that I was taking a chance after our whole downstairs flooded from a toilet overflow after a massive rainstorm. Less than a year, after install we had another massive overflow of the toilet. I cried and we had to empty the down stairs again, but because I had all the walls to floor waterproofed along the bottom edges with Kerdi, I did not have ANY need to repair dry wall. Boy was I happy!!! With the Ditra between the cement and the tile, I have not had any separation of Tile from the floor. And so as a result I am totally convinced, just as you are that Schluter products work. I did a lot of research before doing this and was pretty convinced ahead of time. I have NOT changed my mind, I spent extra money for it but never regretted the decision. Thank You Schluter!!!!!

Very cool my friend. I’m trying to learn a new trick on the job as this isn’t Mike K, I’m a trained chef at a musician and to go from that to carpentry my boss hired me I think just out of sympathy. He knows I don’t know shit about tools but to watch what you do to learn this way that’s what I need. Thank you for what you’re doing God bless and stay safe. Steve.

Thank you! I am using their tile products for engineered flooring and adding heat.

20 yrs installing this product it's the right stuff worth every penny

@petersparshot4997

2 ай бұрын

can you lay it upside down. I done it by mistake

Bro. FINALLY. I’ve been using Schluter of all my tile jobs for years. I always wonder why I didn’t see this in your channel.

@wjthehomebuilder

5 жыл бұрын

@@willpelton1619 Maybe you should take a break from reading all the comments as yours seem to have gotten progressively worse with your frustration from everyone else's opinions.

I used this to fix a crumbling tile landing that had been affixed directly to hardwood with mortar in the 60s or so. Its amazing. Only thing is people need to pick the right adhesion product. Certain mastic/mortar are specifically stated to not be used with these. Super easy to use. 10/10 would recommend

Matt is absolutely right...if you are a contractor doing this kind of work the Schluter line of products is 100% what you want to learn & use.

Awesome stuff, but after taking out a multitude of 1950's bathrooms that were almost completely tiled with some funky colors I might add, they were built some tough !! Found only one with some minor water damage but not bad after 50-60yrs !! Hopefully this holds up as well, as I think it will.

@entropyfan5714

5 жыл бұрын

Chickenwire + thick bed of mortar = make the new guy do the tearout!

@marcfavell

5 жыл бұрын

@@entropyfan5714 tell me about it just tore out a bath with .25 inch drywall then steel mesh with 2.5-3 inch concrete then tile I used a diamond wheel cutter to cut in between the studs and pryed it off in chunks, worst demo ever lol especially aroumd the plumbing and electrical!!

@megenberg8

5 жыл бұрын

@@marcfavell they built it to last - thought the 50's would never end...

@marcfavell

5 жыл бұрын

@@megenberg8 yeah for sure same principles apply now to installs of tile and stone and they also knew it when they made the parthenon just the material technology is different now but same principles!!

@HappyHands.

5 жыл бұрын

i had to tear one out once. it was mud over diamond mesh wire, man that stuff was hard!

I don't know why KZread recommended this to me and I dont know why I watched it but now I'm going down the rabbit hole and watching more.

@rally_9284

4 жыл бұрын

wtfuchattin lmao mr tooo🤦🏿‍♂️

@mrwhosmynameagain

3 жыл бұрын

Where am I?

I thank you for your video. I wish I could find an honest contractor like you. You make it look so easy.

@h2thechizoit445

2 ай бұрын

They all make it look easy, that's why it's on you tube. $$$

We are planning to use this system in our new custom home! As an architect, we always spec Schluter products!

Greetings from Guayaquil, Ecuador. Your videos are of great quality, congratulations. The importance of your dialogues requires that they be translated and put as subtitles. Please try to do so as soon as possible in Spanish, the construction-loving community will thank you.

Yep!.... I thought this product was GENIUS when I first saw it on Mike Holmes’ show! I l😍watching his very informative show....I learned so much valuable information! I have water damage on part of my floating wood and want to replace with tiles. So, this product will be PERFECT to use over my concrete slab- and I NEVER have to worry about title shifting with fluctuating temperatures. I’m so excited, I can see my plan coming together, perfectly!🎊 THANK YOU, for this informative video! P.S. I can buy a small quantity of needed supplies to use in an 33 square-foot area?

@justsorandom764

3 жыл бұрын

Um... Why would you use ditra over a slab?

@justsorandom764

3 жыл бұрын

@Sergey Romanchenko We don't post tension anything not in multistory commercial settings. Here in Wisconsin, we don't pour on grade. We can't. We have a frost line. We dig below it and we do ground prep. thusly making a post tension slab a waste of money. What's it like to have slabs that crack on the inside of a building? I wouldn't know, because we don't. But you already knew all of that because you have common sense and knowledge, right Boris? Man, it doesn't matter where you put a Russian, that inferiority complex just shines like a bright ol' beacon doesn't it Natasha?

Why I only saw this now after painstakingly put a hardiebacker on a multicorner room! Definitely using this on my next project!

I’ve been using Schluter Kerdi and Ditra products… sheets, board, shower pans… making benches, curbs, tub pedestals, etc., for the past 7 or 8 years. It’s versatile, fast… excellent!

Have had 10 years with the Schluter products. By far the best thing since a pocket on a shirt for bathroom remodeling. You can build almost anything you can imagine with Kerdi, Kerdi lined products, and Kerdi board. Highly recommend you get some into your very next shower remodel. It has so many great qualities, it's worth all extra expense and time by far.

@steamsteam6607

5 жыл бұрын

$$Your shilling has been transferred to your bank account$$

@condog42

5 жыл бұрын

Just out of curiosity - what does your shower remodel cost with Schluter. Yes I know "it depends". But I can guess its about $3000 more than without. Great products - but if you cant save time installing - where do you gain anything? If you tell me I'll get a shower that doesnt leak - well, you dont have non-Schluter showers leaking. Show me the gain!

@rhinomite5203

5 жыл бұрын

@@condog42 It's definitely not for everyone. In my opinion, it is the best material for tile showers and I specifically mean custom showers. May not be the best for standard size showers like 5 or 6 ft tubs or tub enclosures. It is not a "cheap" product, I will agree all day. In my opinion, it is a premium product and that why I like it so much. If you're doing budget type remodels or replacements, this may not be the right product for you. If you are doing high end or custom sized showers, this is what you want to use. Kerdi doesn't pay me or even know who I am. But I can tell you I have 3 personal showers, all tiled and all lined with Kerdi as well as Kerdi niches, curbs, and benches. I was skeptical myself when I first heard of Schluter. The fact that it is completely waterproof when installed correctly, is all needed to hear. I do my own demo and rebuild right up through the Kerdi install and that saves me time and money not paid to someone else. While my tile layers are tiling, I'm onto the next job or outside building something else. What works for me doesn't work for everyone, but you will not be disappointed with any of the Schluter products. Give it a shot on your next shower remodel and then feel free to comment back on what you think. I'm always looking for pros and cons to improve my business.

@RandomGuy-nm6bm

5 жыл бұрын

Wow. This review doesn't sound bought and fake at all.

@rhinomite5203

5 жыл бұрын

@Larry Riffett Hey Larry, despite some of the comments that say '"Im paid for my reviews", I am not paid, nor would accept any compensation. With that being said, I personally have not used the Schluter floor product I know as Ditra Heat yet. As soon as I get the opportunity, I will definitely leave my comments. I would trust in my own bathroom, but at this time do not have any to report on. I wish I had my master bath floor heated with it!

as a builder/remodeler this system seems to be wonderful. I will install it in my own soon to be spa room on the third floor of my house and keep u posted as to the developments with this product/s.

@Protectourbioshpere

2 жыл бұрын

I learned about rhis recently, and we used it on a bathroom remodel we did. I will say that it is awesome. Very easy to install and covers all your bases. I would definitely use it again.

Thank s for sharing!! I am in Texas and removing carpet on 2 bedroom floors with concrete underneath. will definitely show this to the man replacing it.

In Sweden we have a thinner membrane with taped corners. All glued with a 2component glue. The level is fixed before so all surface angles down to the drain with a steel mesh net in it, so that ”cake” won’t crack if the foundation moves.

Basically ignored everything the guy said because I was too transfixed on the dude laying down the thinset

@judichristopher4604

4 жыл бұрын

LAUGHING... RIGHT... ME TOO

@KKhhoorrnniittee

4 жыл бұрын

Matt wasn't paying too much attention to him, so you did (-; Me too.

@OxAO

4 жыл бұрын

The guy talks says nothing. While they show another guy doing the work that is hard to see what he was doing. Nearly worthless video

@nobsmusic9358

4 жыл бұрын

Hahahah me too! While watching I just kept thinking 'He's never going to get good adhesion to the back of that shluter' lol. That's what happens when you spread thinset over particle board. The particle board soaks up all the water from the thinset and the materials don't bond. Total crapola install! LOL

@nobsmusic9358

4 жыл бұрын

I also got a kick at 6:45 when the guy was struggling to get mud out of the bucket using his notch trowel. Could he not afford a pail scoop or any number of trowels/knives that could get help him get that mud out faster? That was almost painful to watch! Lol

I first saw this on "I Like To Make Stuff" mudroom renovation video!

Wish I had known about this a couple of years ago. Would have saved me so much trouble.

As usual, very informative important (must have) information. Your videos should be considered for credit for continuous education units for contractors.

Love your videos Matt ... Thank you!

I installed this when I remodeled our master bath, complete custom shower, tub area, and flooring. About 500sq total tiling, including shower. It was an easy install and I really liked the fact that I can waterproof areas easily. My original tile floor was about 1" thick and now it is about 1/2" thick, so now I have door jams that have gaps, not sure what do about that. I would recommend this product to anyone think is building or remodeling a home. Also, building the shower curb was a breeze and looks amazing. They have products that make the install look clean and professional. I was able to get all my products from Lowes and they had everything in stock.

@RodneyFisk

5 жыл бұрын

For the bottoms of your door jambs, I recommend plinth blocks. They have them in stock at the big box stores. They're square and make the room look much more expensive. Just mark around the block with a pencil and cut away the casing and baseboard with an oscillating multitool. For the baseboard gaps, I recommend 'stop molding.' It's the molding on the door frame, that stops the door from going any further when you close it.

A few years ago, I have installed this Schulter Ditra underlayment plastic and have marble over at the second floor bathrooms. Now, every time my husband is in the master bathroom I know because I heard squeaking noise from Schulter Ditra and I regret I don't choose hardboard underlayment.

I've used this on 3 separate floors and the results are amazing. This substrate is super easy to work with and lay down and it's easy to lay tile on too. The only downside is the price. It is expensive. Now that I've used it, not ever returning to backerboard or cement board.

I have always enjoyed watching Mike Holmes use these products on all of his shows.

@kennethdean4349

3 жыл бұрын

I lot all respect for Mike Holmes when he endorsed 3M Filtrete "furnace killer" air filters.

@marcopoulin1897

3 жыл бұрын

Mike holmes doesnt nothing about tile instalation hes dick

@isailwind3471

3 жыл бұрын

Holmes is a sellout, he was sponsored to promote this crap. I have no respect for him since he flogged this crap on his show.

@Will_Wel

3 жыл бұрын

@@marcopoulin1897what the hell are you talking about? How's he a dick?

Since I am deaf enough to need captioning, I watched once for action in background, once more to read. For a bad builder job master shower replacement, I gutted walls to metal studs over concrete slab (South Fl), replaced, added and reinforced studs, and did .5" cement board, doubled on longest wall. Properly notched grey pudding type waterproofing over all. Walls, floating bench (not the block type shown here), arched niche, upper corner shelf bowl draining cement pan to direct drain. I used several Schluter products....corner membrane, faucet water proofing pieces, drain top. But I am still with cement board. Properly done, cement board just makes me feel like it will BE there for awhile. If you want it done right, DIY. Or micromanage a select subcontractor. 😉 122 lb lady DIY'er

Used schluter on a bathroom renovation I did. On the floor and in the shower. Made my life so much easier

Man thank you and thank you KZread algorithms! I need to replace linoleum in my basement from a massive water leak. It is on concrete and was concerned about cracks. Will definitely check this out.

currently doing this in a second floor laundry room 6 inches up the wall with an emergency drain, the stuff is bullet proof when installed right

Amazing product, if installed properly. Highly recommended

@Peterzach85

4 жыл бұрын

Robert Petrarca It’s one of the worst fucking piece of shit of material that you could possibly use use hardy board or hardy backer get rid of the shit I’ve done nothing but deal with the lawsuit with this

@AttilioDiMarco

3 жыл бұрын

I have to be concerned with anything that requires me to send my tile installer to a new class.

Used this system back in 2006 - yay! Yes, we have concrete floors with tile and I have cracks in many tiles at my ranch - wish they would have done something long ago when they set that, but what you gonna do. God bless! 🇨🇱

It’s been close to 20 years we use this stuff in Canada. Great product but expensive too. Would use it any day

Seeing a lot of these 'membrane' applications around YT these days. Good! I've been using rubber membranes between my dry wall/plasterboard since the 90's. I always fit highest quality double glazed windows too. #1 complaint of most private tenants is sound/air pollution. Always found it totally mind blowing that 99% of landlords don't think this matters. Guess they enjoy turning over tenants every 6 months! I think I've saved myself thousands of hours wasted on admin/checks over the years. A well maintained property = happy long term tenants. No brainer!

@samheasmanwhite

3 жыл бұрын

I can't believe that some places still allow builders to install single glazed windows for living spaces, the quality of life benefits from the thermal/sound blocking is so big that it should be in every building code. Not to mention poor ventilation is so common if left up to the tenant so you don't want condensation to wreck the sills with mould.

@MyFortressConstruction

Жыл бұрын

What rubber membranes do you use? Researching sound deadening and there's lots of opinions. Most recommend 2 layers of 5/8 as the most cost effective method. Thanks

I see the resistance of "Experinced installers" like those posting here - watched that happen for years at Lowe's same with epoxy grout - installers hated it because they had to go slower and couldn't slap it up and run out the door - Schlutter, Epoxy grout and a number other newer products take a little more time, more skill and yes more cost to customer - in the long run the customer wins and the installer saves time on call backs and fighting with customers over failed installs. BUT you have to do it right or it won't work - that means CHANGING your work habits.

@marcopoulin1897

3 жыл бұрын

Epoxy grout only commercial projet dont ask me for house

@Matt Risinger, good deal. I'm also in Texas. Just north of Dallas, but about to move to the Houston area, and I know exactly what you mean about cement pads. So far, I haven't had any call backs for cracked tile, but, I have repaired many cracks. This stuff looks good.

Schmitty rocks! Nice work, Matt, always appreciate your presentations.