I redo of my video on how to repair and maintain a VCI- 300 and a VCI-300 MKII www.djskd.com DEEJAYSKD @DJ_SKD / djskd
Жүктеу.....
Пікірлер: 19
@357djrms9 жыл бұрын
So i saw this controller at a pawn shop and they said its broke pads flash when you try to touch them. Said would cost about 200-300 from vestax. I said thank you walked away did a youtube search. Watch this video and ask the shop ill pay 80 bucks for the vci they said yes go home follow this video and it works perfect! !! Its in great shape and now im rocking!! You sir are the man! Thank you for this video saved me a lot of loot and have a fun controller now
@binx10311 жыл бұрын
i followed your instructions and serviced mine it works flawless now.keep up the good work thanks...
@Panslapper11 жыл бұрын
,,,but a better mould for future acrylic platters would eliminate this problem with ease. Approx 0.5 mm extra area growth is needed to get a snug no play fit. Which is not alot but certainly more than enough to knock the wheel off center without it. Peace.
@Panslapper11 жыл бұрын
Word of warning if you do self service, which I did, then when replacing the jog wheel post service ie screwing them back onto the unit then you have to get the plates dead center if you do not like off center spin back. The spin back sound is not affected neither is the scratching but only the actual platter as it spins will look wobbly/off center. Be gentle and patient and centralie the acrylic plate and alu touch plate and hold down with your fingers with a little pressure then, cont..
@piterisparkeris47705 ай бұрын
I have the VCI 300 MK1, and there is an issue with the right deck tempo fader. It indicates 0, not in the middle like it does on the left side. The green LED lights up when the fader is two sections above from the center. Have you ever experienced this kind of error?
@Panslapper11 жыл бұрын
cont..put two screws into the platter and spin it. You will see instantly if the platter is off center or not. If it is off center then take the two screws back out and attempt to centralize again...you will get it right so don't worry. My first self service and it took two or three attempts before patience won and the platters were cenrtalized. This is due to a very small ammount of play in the platter fitting onto the motor which is an engineerreing shortcoming. No offence to Vestax but..
@djzyon15353 жыл бұрын
Hi, i have a problem with the two sensitivity adjustments that controls the platter or jog wheels. It stops from playing when i touch the jog wheel. How can i solve this problem
@sendchrisanemail11 жыл бұрын
It sounds like it's still sensitive to touch, but not to the position of the platter. My guess is that you may have an issue with that optical sensor that he tells you not to disturb. I would check the wires that go to the sensor to make sure that everything is hooked up correctly.
@steadynow10 жыл бұрын
Thanks for the great video. I have the same model but the headphone preview buttons are a getting a bit sticky, any recommendations for a repair/clean.
@only1bigshot11 жыл бұрын
great video, thanks, but i have a question for you. I only use my vestax mci-300MKII a couple of time so i know there shouldnt be dust or dirt inside, but from day one i had a problem with the left jog wheel. the seneitivity is off. It dont turn red when i touch it. If i turn the knob on top to where it does turn red, then it wont go back to blue. Im only having this problem with the left side, right side works perfect. What do you suggest i do? thanks so much.
@jinba83523 жыл бұрын
Hey noudo. This is a bit of a stretch but would you by any chance know how to repair a VCI-400?
@boomshotta11 жыл бұрын
My right jog wheel was slippin a bit when I was in scratch mode. I watched your video and took it apart to give it some cleaning. I can no longer scratch at all now. The wheel still turns red when I touch it and stops the track from playing, but can not scratch at all. The side of the platter no longer works for speeding up or slowing down the track either. Any ideas?
@JorgeVictoria6 жыл бұрын
Gracias
@djtheoevents11 жыл бұрын
my tension wheel dose not seem to be adjusting.. what do u recommend?
@Panslapper10 жыл бұрын
Anybody know what I could lubricate my faders with on the 300 mk2? No time wasters please!
Пікірлер: 19
So i saw this controller at a pawn shop and they said its broke pads flash when you try to touch them. Said would cost about 200-300 from vestax. I said thank you walked away did a youtube search. Watch this video and ask the shop ill pay 80 bucks for the vci they said yes go home follow this video and it works perfect! !! Its in great shape and now im rocking!! You sir are the man! Thank you for this video saved me a lot of loot and have a fun controller now
i followed your instructions and serviced mine it works flawless now.keep up the good work thanks...
,,,but a better mould for future acrylic platters would eliminate this problem with ease. Approx 0.5 mm extra area growth is needed to get a snug no play fit. Which is not alot but certainly more than enough to knock the wheel off center without it. Peace.
Word of warning if you do self service, which I did, then when replacing the jog wheel post service ie screwing them back onto the unit then you have to get the plates dead center if you do not like off center spin back. The spin back sound is not affected neither is the scratching but only the actual platter as it spins will look wobbly/off center. Be gentle and patient and centralie the acrylic plate and alu touch plate and hold down with your fingers with a little pressure then, cont..
I have the VCI 300 MK1, and there is an issue with the right deck tempo fader. It indicates 0, not in the middle like it does on the left side. The green LED lights up when the fader is two sections above from the center. Have you ever experienced this kind of error?
cont..put two screws into the platter and spin it. You will see instantly if the platter is off center or not. If it is off center then take the two screws back out and attempt to centralize again...you will get it right so don't worry. My first self service and it took two or three attempts before patience won and the platters were cenrtalized. This is due to a very small ammount of play in the platter fitting onto the motor which is an engineerreing shortcoming. No offence to Vestax but..
Hi, i have a problem with the two sensitivity adjustments that controls the platter or jog wheels. It stops from playing when i touch the jog wheel. How can i solve this problem
It sounds like it's still sensitive to touch, but not to the position of the platter. My guess is that you may have an issue with that optical sensor that he tells you not to disturb. I would check the wires that go to the sensor to make sure that everything is hooked up correctly.
Thanks for the great video. I have the same model but the headphone preview buttons are a getting a bit sticky, any recommendations for a repair/clean.
great video, thanks, but i have a question for you. I only use my vestax mci-300MKII a couple of time so i know there shouldnt be dust or dirt inside, but from day one i had a problem with the left jog wheel. the seneitivity is off. It dont turn red when i touch it. If i turn the knob on top to where it does turn red, then it wont go back to blue. Im only having this problem with the left side, right side works perfect. What do you suggest i do? thanks so much.
Hey noudo. This is a bit of a stretch but would you by any chance know how to repair a VCI-400?
My right jog wheel was slippin a bit when I was in scratch mode. I watched your video and took it apart to give it some cleaning. I can no longer scratch at all now. The wheel still turns red when I touch it and stops the track from playing, but can not scratch at all. The side of the platter no longer works for speeding up or slowing down the track either. Any ideas?
Gracias
my tension wheel dose not seem to be adjusting.. what do u recommend?
Anybody know what I could lubricate my faders with on the 300 mk2? No time wasters please!
Nice one mate!
Awesome shirt!
My play button is Jamming! Any tips on fixing?
Yup! you were the first.