My mic died so so all the audio is from the camera, and then heavily processed. Sigh. Music at end: Filaments by Scott Buckley - released under CC-BY 4.0. www.scottbuckley.com.au T-shirt: www.ndthero.com
Жүктеу.....
Пікірлер: 20
@robertdoiron13792 күн бұрын
great video
@bobwayzie Жыл бұрын
Good video, been waiting for a straight forward, spell-it-out backing bar video.
@ndthero Жыл бұрын
Great job Paul and thanks for the shout out for the art.
@larryrichardson8734 Жыл бұрын
Always informative, always enjoyable...
@ashleylongley623 Жыл бұрын
Doing alot of exactly what you've demonstrated, single bevel backing bar, but 25, 28 and 32mm, exactly what you said, to start with shaking my head and ruler (Aussie in Australia ) out every 5 minutes, but now I look for the signals as a guide
@robertdoiron13795 ай бұрын
thanks Paul!
@ahmedmansuor9513 Жыл бұрын
Great dimo Thanks from Egypt
@dinho9492 Жыл бұрын
Nice
@samajira Жыл бұрын
X3, Gekko, Veo and a 5 dollars Mic 😅
@hollowayndtengineeringinc.5201
Жыл бұрын
I know right? :)
@bladexxlll6615 Жыл бұрын
Would be good to see your tutorial/explanation on scanning partial penetration joint welds with UT conventional
@hollowayndtengineeringinc.5201
Жыл бұрын
If I had a sample I would. The conclusion would likely be: don't do it, too much geo.
@weldingclassroom71716 ай бұрын
Thanks. I am introducing my HS students to NDE and checking their own groove welds. I'm a novice but very thankful for your videos. I spent hours yesterday playing with our UT machine and some vee grooves with backing. On that root signal, how would a bit of unfused bevel edge look?
@hollowayndtengineeringinc.5201
6 ай бұрын
Great question! On the near side, pretty easy. The first of the twin peaks signal will rocket up. But on the opposite side it's much more difficult.
@santiagocruz9060 Жыл бұрын
Usesfull
@turdburglar1612 Жыл бұрын
Does Canda require those big 🐌 wedges that AWS calls out?
@hollowayndtengineeringinc.5201
Жыл бұрын
No
@hossammohsen1119 Жыл бұрын
Kindly can you explain this with using phased array
Пікірлер: 20
great video
Good video, been waiting for a straight forward, spell-it-out backing bar video.
Great job Paul and thanks for the shout out for the art.
Always informative, always enjoyable...
Doing alot of exactly what you've demonstrated, single bevel backing bar, but 25, 28 and 32mm, exactly what you said, to start with shaking my head and ruler (Aussie in Australia ) out every 5 minutes, but now I look for the signals as a guide
thanks Paul!
Great dimo Thanks from Egypt
Nice
X3, Gekko, Veo and a 5 dollars Mic 😅
@hollowayndtengineeringinc.5201
Жыл бұрын
I know right? :)
Would be good to see your tutorial/explanation on scanning partial penetration joint welds with UT conventional
@hollowayndtengineeringinc.5201
Жыл бұрын
If I had a sample I would. The conclusion would likely be: don't do it, too much geo.
Thanks. I am introducing my HS students to NDE and checking their own groove welds. I'm a novice but very thankful for your videos. I spent hours yesterday playing with our UT machine and some vee grooves with backing. On that root signal, how would a bit of unfused bevel edge look?
@hollowayndtengineeringinc.5201
6 ай бұрын
Great question! On the near side, pretty easy. The first of the twin peaks signal will rocket up. But on the opposite side it's much more difficult.
Usesfull
Does Canda require those big 🐌 wedges that AWS calls out?
@hollowayndtengineeringinc.5201
Жыл бұрын
No
Kindly can you explain this with using phased array
Hi can anyone tell me what’s the equipment?
@annupazuzu8471
Жыл бұрын
Sonatest Wave