Upgrade - Emergency LED Light with Li-ion Battery and Mobile Charging | Lead Acid To Li-ion Battery
Ғылым және технология
In this video shows the upgrade lead-acid to Li-ion battery for emergency LED light using TP4056 Li-ion battery charging module with 18650 Li-ion 3.7v battery
----------------------------------------------------------------------
the component is using
1) TP4056 Li-ion Battery Charging module
2) 18650 Li-ion 3.7v battery
3) old emergency light
18650 Li-ion 3.7v battery
Banggood - www.banggood.in/custlink/vDKv...
Amazon - amzn.to/2XQsMWC
TP4056 Li-ion Battery Charging with Protection Board
Banggoog - www.banggood.in/custlink/KKGm...
Amazon - amzn.to/2YL6bvz
----------------------------------------------------
1)Monitoring & controlling project circuits - goo.gl/UUT2CG
2) Inverter circuits - goo.gl/xz33Uu
3) Chaser LED lights circuits - goo.gl/5aRnU4
4) DC Power supply circuits - goo.gl/yt4fuP
5) Remote control circuit - goo.gl/rJzx1d
6) LED-based circuits - goo.gl/pga5qh
7) Relay-based circuit - goo.gl/Q4r7XM
8) PIC Microcontroller project - goo.gl/9tNaVm
9) Relay-based circuit - goo.gl/J4u8BD
10) Battery controller circuits - goo.gl/YVHokC
11) Repair works - goo.gl/11uPxn
12)Transformerless power supply circuits - goo.gl/c9zv
13) solar System - bit.ly/2m0g4q6
14) Audio System - bit.ly/34ZSlYtbit.ly/2...
15) Useful Tool videos - bit.ly/2k3xodc
-----------------------------------------------------------------
buy more material by the following a link
solar LED Wall light
Banggood - www.banggood.in/custlink/DDDm...
Amazon - goo.gl/48Kxnb
12v Solar Battery
Amazon - amzn.to/34LaNFc
Banggood -bit.ly/2VKeczY
3S 12.6v 18650 Li-ion Battery Charge BMS Protection and voltage balance Board
Banggood - bit.ly/2SabPFL
Amazon - goo.gl/uy6YwM
18650 Li-ion 3.7v battery
Banggood - www.banggood.in/custlink/vDKv...
Amazon - amzn.to/2XQsMWC
4S 16.8v BMS Li-ion battery charger board
Banggood - bit.ly/36ohkWD
Amazon - amzn.to/2QlsjdI
3S 20A Li-ion Battery 18650 Charger PCB BMS Protection Board 12.6V Cell -
Banggood - goo.gl/7jfnBM
Amazon - goo.gl/uy6YwM
Digital LED DC Volt Meter
Banggoog - www.banggood.in/custlink/vvDD...
Amazon - amzn.to/2P6vR12
12V /24V 30A PMW Solar Charge Controller
Banggood - bit.ly/2yqMKQ1
Amazon - amzn.to/2yuUQqw
DC-DC 12-35V 150W Boost Adjust Module -
Banggood - www.banggood.in/custlink/DD3m...
Amazon - amzn.to/31DGcYb
LM2596 dc-dc buck converter step down module =
Amazon - goo.gl/pxH5AR
Banggood - goo.gl/eg6WSn
MT3608 2A dc-dc Step Up Boost Power Module =
Amazon - goo.gl/c4Ys6P
Banggood - goo.gl/pKbCHe
--------------------------------------------------------------------
Пікірлер: 45
Now it's a manual ordinary light not an emergency light you have to turn on and off manually originally it turns on when AC mains fail
@rajvjnair
Жыл бұрын
cket and cabledont use the charging module try uaing the already given sov
Very clearly explained
Great bro.I have this one.I think that what can I use instad of these batteries (3 battery) My problem is solved.Thank you.
good keep it up
Very nice
ऐसे और DIY Bano
Can we aslo charge with that AC charger with it, which was used to charge those acid batteries.
Your TP4056 does not have low battery voltage protection, your batteries will be ruined
Hi bro, can the output charger acid for input to modul tp4056? So we can using AC power to charger
Nice
What of over discharge protection? You could have attached 3.7 BMS to each 18650cell. You can salvage them from old phone battery..
@powergen522
4 жыл бұрын
yes, this is without protection BMS board, but you can change within protection BMS board, and this is old laptop batteries.
@kimo4646
4 жыл бұрын
Thanks bro
does the change in brightness remain unchanged? thanks
I just removed the Xrated capacitor 155 and bridge diodes from same PCB and connect the cords of 5volts DC pin at filter capacitor's +ve and _ve terminals, and the then connect the 3.7 v cell phone battary with PCB's battary terminals. In this way when 5volts input is given the auto on off switching of emergency light is working properly and charging is normal with 1amp charger. You may try my way and will be glade to see the result.
You need circuit with over discharge protection.
if i just replace the acid battrry with 3.7v lithium will it still charge ?
Pls answer Sir, can other existing charging port still use?
Sir 12 Vol 20 Amp Charger ko Repear Karday ?
you did not try plugging the usb power source in "on" mode if it wil put off as emergency lights do. .and automatically "on" during brown-out. .👍
Bro.. why do we need external micro USB cable as already micro USB port existed in tp4056 module na..
@powergen522
3 жыл бұрын
it convenient to anyplace, so your choose
Is there a manual switch or it is an auto turn on emergency light? I need an auto emergency with the TP4056 IC PLEASE HELP
@allinalladityan318
2 жыл бұрын
need to use a relay
yes i have already made this
How to find led wattages in this lights?. How to check lead acid batteries vg and a and mah?. How to select proper matching Li ion cell vg and mah? Kindly share the details
R2,3,4 ki value bta skte ho?
What if someone connect it directly to the ac main using adapter???
can we charge directly theough the charging source already present in the emergency light or do we need charging module
@xx_saadi
Жыл бұрын
You may use the existing PCB. Just remove the X rated capacitor 155 , 390 k bleeder resistor and bridge rectifier diodes, now take a DC charging socket and connect its terminals carefully with filter capacitor's +very and _ve terminals and then connect 3.7 volts batteries (must be connected in parallel) and connect at the pcb's + and _ terminal. Then take 5 volts, 1amp charger whose charging pin should be according to the hole of DC charging socket. In this way you may 100% use the existing charging circuit and also enjoy the auto on off switching mode of emergency light. I did the same one week ago and my dp emergency led light is working wonderfully.
@tun_geol
Жыл бұрын
@@xx_saadi do you hav a tutorial?
Isska price kya hai sir
what is price of batteries
can you charge it using 220v port?
@powergen522
2 жыл бұрын
Yes you can use added 5v mobile adapter in light
this board can charge only one battary..this board not for 2 batteries, board got heat
I have Dp Led light But this is 8 watt 9110 model. It has 3 lead Acid battery but i dont know Its voltage ? Because of both are zero Fucked. Connection is +++,--- parrallel. I connect one full charged protected Nitecore 3.7, 18650 battery. But Lumence is low on full mode. Not 8 watt, not as compare to privious lead Acid Lumence. Q1 how to increse energy or Lumence? 1) if Connect 3.7×2( 7.2 volt 18650)??? 2) Use "High Drain" model of 18650???
its not an emergency light anymore . .
Can I use 5 batteries for this?
@powergen522
3 жыл бұрын
yes, but the charger module will produce overheat
Is this Bluetooth module is capable of charging this lead acid battery?
@kmazahreh
3 жыл бұрын
This is TP4056 Micro USB Charger with Protection (1 A)
Hair Anna I now vivin
How to find led wattages in this lights?. How to check lead acid batteries vg and a and mah?. How to select proper matching Li ion cell vg and mah? Kindly share the details