Hi Mike, thank you for the video and saving us a lot of time! For those who are asking about losing access to the tp-link router/ bridge after saving the setting, I was in the same boat but I found this simple solution to work. I checked the IP range the main router with internet access uses for dhcp, and assigned the tp-link bridge with something within that range rather than sticking with default 192.168.0.x range as shown on the video. That's it! many home routers use default subnets like 192.168.100.0/24, or 10.10.10.0/24. in this case my home router uses 192.168.1.0/24 range, so I assigned an un-used IP in that range to the tp-link bridge - lets say, 192.168.1.188/24. This allows you to still connect to the tp-link router even when its in bridge mode. because technically speaking you are still connected to the main network (router with internet), so the main router should have a way to reach the tp-link bridge. that's only possible if they are both using the same range. Hope this helps!

@MikeNovelli

11 ай бұрын

Dude! I have been looking for this comment for a while now... It got held up in the youtube comment review for some reason. I think this might be the key to helping a lot of people who have been having this issue. Thanks so much for your contribution!! I'm going to try to pin this in hopes others might see it and resolve their issues.

@alitaherimoghadam8894

9 ай бұрын

@@MikeNovelli Thanks! happy to help

@michaela.8960

9 ай бұрын

Thanks@@alitaherimoghadam8894 . I was in the same boat. Between Mike and you, I'm running fine! Many thanks.

@joshisidro

4 ай бұрын

Hey can anyone help me. I cant access the router as well. Is there a way to find that IP?

@MikeNovelli

4 ай бұрын

@joshisidro try hard resetting it

Googled for an hour and finally found this video… saved my life. I am impressed by how simple but hidden this is thank you so much for sharing with everyone.

@MikeNovelli

Жыл бұрын

Yep. That's why I made it. Glad it helped!

@jamestate4488

Жыл бұрын

@@MikeNovelli I’ve had to redo this setup multiple times just randomly disconnects. All the lights are on and just says “unidentified network no internet” Thanks

@MikeNovelli

Жыл бұрын

@@jamestate4488 I don't know. Perhaps you are too far and losing connection from interference at some point. Try moving it closer and see if the issue persists. Otherwise hit TP-Link support up. I suggest calling if you can.

@jamestate4488

Жыл бұрын

@@MikeNovelli Sorry for the late update, contacted support and it was running fine until 2 minutes ago. Still outputting a connection but when I go on the local it does not say running and no matter how many times I change the settings it needs fresh restart.

@jamestate4488

Жыл бұрын

When I contacted support all they did was help me update drivers and that was it

Mike you are a machine, I've been trying to do it for 3 hours and there was no way, I looked at your video and I got it after 5 min. Thank you very much, greetings from Spain

@MikeNovelli

2 жыл бұрын

We are all just biological machines converting nutrients into electrical activity. Glad it helped. Tell the Spanish women I say hi!

Mike, Thank you so much. I am banging my head over this for more than 2hrs now. You were absolutely a hero after sharing the info about IPTV settings. I have had my fair share working with networks but I would never guessed it.

@MikeNovelli

2 жыл бұрын

You are very welcome. I didn't want others to have to deal with the same issue I had. Or to at least overcome them if they had the same thing happening. Thanks for your kind words!

@TheArkadyuti

2 жыл бұрын

@@MikeNovelli possibly you might have replied to wrong thread.

Brilliant, thank you. Now enjoying my internet signals, they're bouncing everywhere, we're having a great time.

@MikeNovelli

Жыл бұрын

Be safe out there.

Thank you dude! Nobody else had this explanation after searching for an hour.

@MikeNovelli

5 ай бұрын

You're welcome man! glad it helped ya.

You're legend. I'm now enjoying my signal, the internet, and the people on the internet. Thank you!

@MikeNovelli

Жыл бұрын

Heck yeah. Be careful out there! There's a lot of not so nice people on the net.

"Have a good time, and...enjoy your signal, and...the people on the internet." - Thank you Mike, this was super helpful, and I laughed snorted at your sign-off.

@MikeNovelli

4 ай бұрын

😃

@911Privacy

4 ай бұрын

Thank you , this was super helpful for us

lol back at this video again! i watched this a year ago and had to come back for the same setup! Thanks again Big Mike !!!!

@MikeNovelli

3 ай бұрын

That's what it's for. Good job using your resources to accomplish a task. 👍

Yes! I was having that issue! Nice to find your video explaining the last step for IPTV. Thank you!

Thanks for this! Much easier and faster than the other videos or online reads. Got it up and running I got fast speeds now everywhere.

@MikeNovelli

2 жыл бұрын

Glad it could help!

Hi Mike.! You forgot to uncheck the NAT under System tools., FYI.. it will be enabled by default. Goto -> "System parameters" appears as the last option after WDS settings.! NAT is not required while the router is in bridge mode., which may reduce or cause lag to the network speed by pushing it into "Double NAT processing".

Thanks So Much This Method Still Applies As Of 2/21/24 For Anyone Wondering

@MikeNovelli

5 ай бұрын

Heck yeah. Glad it worked out. 🫡

Working with a setup with 2 routers that couldn't be wired, and passthroughs didn't work. Life saver.

Thanks, Mike!!!! You're a lifesaver. I had given up on the thoughts of this, thinking that my router wasn't capable of this. Thank you!

@MikeNovelli

11 ай бұрын

You are very welcome. Glad this helped you.

Super!! ..you saved me from buying an extra new repeater. Thanks for sharing this 🙂

@MikeNovelli

5 ай бұрын

You are very welcome. Glad it helped ya.

Thanks so much man, was trying to do this for 4 days, you helped alot

@MikeNovelli

2 жыл бұрын

You're welcome!

I have a C900 and I cannot access the internet if I check the enable IPTV box. Unchecking it worked for me.

Great video Mike. The last step that my router needed was a reboot. Only then was I able to access the Internet through it. Did anyone else have the same experience? Mine is the Archer C7 v5.0 bridged to a TP Link AX1800. I have dumped TP Link for most of my networks in favor of Asus, but that's just me. TP Link is a pain in the ...

@MikeNovelli

8 ай бұрын

Have not heard that. But I did hear a lot of people saying they would have to repeat the setup process after power loss so you may want to check the pinned comment. I cannot say I disagree with your TP Link sentiment... The only TP Link product I am running currently is a 24 port switch. But If I need a hard connection RJ45/Ethernet in my garage I use the Archer. I was originally using this method for running a mining farm in my garage but all the Bitmain miners required a cable and it was easier to bridge than to run adapters for each rig. Hope this keeps ya solid into the future.

@datapro007

8 ай бұрын

@@MikeNovelli You helped me out big time, thanks. TP Link left the last step out of their documentation, not good. I'm on the air now bridging a POE camera to the 'net - whew! Anyway, I have used a lot of TP Link network devices. Seems like the user interface has gone from bad to worse in recent times. I'm no Asus fanboy, but I have been having better luck with their products. I'm not making a commission, so I'm not trying to persuade anyone on what brand to buy. They all have their annoyances.

@MikeNovelli

8 ай бұрын

@@datapro007 yep. I'm currently using a Netgear Nighthawk gaming "router" as an AP for WiFi because of the coverage it offers. Began with the Linksys WRT styles way back when and have used a ton of different brands. They can all be a pain, but the most important thing is whether it accomplishes what it needs to. If it does then sometimes I'm willing to deal with the pain to get stuff done.

Thank you so much 🙏🏻 There are lot of other random videos which did not help and i just wasted my time… Your last part of IPTV helped me… Thanks again!!!!

@MikeNovelli

Жыл бұрын

You are welcome. That last part took me a while to figure out and once I did I figured others could use the tip. Glad it worked out

THANKS! It worked on Archer C6 as well.

@MikeNovelli

4 ай бұрын

Awesome. Glad to hear it worked for you!

Great video. The only one that made it work for me. THANK YOU

Doing everything on my c6 and c6u after restart the router all wds setting are use less not connecting anymore until u reset and reconfigured again

on my WDS status it says Assoc insted of run and i dont have internet acces what can i do?

@MikeNovelli

Жыл бұрын

Are you sure the device you are trying to connect to has internet access?

Thanks a ton for giving a heads up to turn on the LAN ports. I did the same steps as mentioned by you and the ports work fine on my TP-Link Archer AC1200 that I use as a repeater. Subscribed to your channel.

@The888Generation

Жыл бұрын

Does TP link ac1200 support wireless repeater mode as tp link 841??

@srivastava18

Жыл бұрын

@@The888Generation I'm not sure about 841 but my Archer AC1200 works well as a repeater.

@blammarus7166

Жыл бұрын

My Archer Ac1200 only gives internet via ethernet cable, however ig i trzy to connect to it using my phone it doesn’t work

Thank you ! Your steps helped me to configure my TP Link router as a extender

@MikeNovelli

Жыл бұрын

You are very welcome. Glad it worked out for ya!

It has a feature named "Lock to AP" in WDS Bridging. What does it do? Should I enable it? For context: We have a different main router and bought a tp link router for its parental control features. I use the main router for online gaming. Edit: Your video helped me a lot with navigation.

@MikeNovelli

2 ай бұрын

Lock to AP just means that it will "lock onto" the single Access Point you connect to even if there is another Access Point with the same credentials, SSID and Password, in range. It basically means it will only connect to the one wireless device to get its signal. Unless you have another AP with the same name and password I would just leave it off. community.tp-link.com/en/home/stories/detail/514

Thanks so much for this! Saved me a lot of headache 🎉

@MikeNovelli

2 ай бұрын

You are welcome SusieQ!

In recent version when connected using 5ghz wds option channel is set as fixed value which is same as master router but problem with this is when my main router gets restart this channel gets changed to some other value so repeater doesn't work until reconfigure it. Cannot change channel as auto in c6 as that option appearing as disabled post was bridge

Thank you MR MIKE i have the same router like yours and it was easy you are a brilliant person

@MikeNovelli

Жыл бұрын

🙏

Excellent guide! TP-Link official site should buy your guide

@MikeNovelli

Жыл бұрын

TP-Link doesn't care... 🤷🏼‍♂️

Thank you! It was driving me crazy because of the missing last step

@MikeNovelli

Жыл бұрын

You're welcome!

I have no idea why but my router doesn't have the "Enable WDS bridging" checkbox that you see under System Tools/Advanced in this video at 1:45 . I don't see a Survey option either in this page at my end

@MikeNovelli

2 жыл бұрын

I also have no idea. Sorry!

@mizutani5138

Жыл бұрын

Me too

I don’t have a system tools option

Thank you. They definitely forgot that last step. I needed this :)

@MikeNovelli

Жыл бұрын

Hell yeah Melody! Glad it helped.

Thanks buddy. Helped me a lot. Espeecially the last missing step. Greetings from Germany

@MikeNovelli

11 ай бұрын

Heck yeah. Good work. I haven't been back to Germany since I was 16, but man did we have fun then!! Glad it helped ya

Hey this video has been super helpful so far! I am not complete yet as I don’t have a system parameters tab and have clicked through all the other tabs I have and nothing supplies me with what I need! I have updated the router and have checked everywhere! Can anybody help me!

@tylerleduc3797

2 жыл бұрын

also the model i have is the ax3000

@MikeNovelli

2 жыл бұрын

@@tylerleduc3797 sometimes they hid them deep on the sides or you have to scroll to find it. I am not sure, but check the manual and/or contact support.

Well this sadly :( is not availble for the TP link AX1500 Archer AX10. That one does not have the repeater option (only router and AP) and the TP-link website looks quite different (probably updated since this video was made). Sharing in case someone has the same and is wondering.

@MikeNovelli

4 ай бұрын

Thanks for sharing.

Hi Mike Thanks heaps for taking the time to post this. It was very helpful & informative. I found using the RESET button helpful and notice a weird thing - when I reset my Archer D7 AC1750 to factory defaults - I can see IPTV options - whereas in my previous configuration I must have somehow unchecked this and could see NOT see the IPTV ports. P.S. Not a criticism - but I also could not hear the audio on my iPhone or Laptop (with both my laptop volume & youtube both turned up to maximum volume). I had to cast to my TV and crank up volume in order to hear it.

@MikeNovelli

Жыл бұрын

Glad it helped. Sorry about the volume. I'll check KZread studio to see if I can boost the gain.

Thanks for the help. ❤

@MikeNovelli

Ай бұрын

You're welcome 🤗

I’m attempting to use my archer c4000 to “extend” my main router signal so that my cameras in my barn can connect to the internet. I thought I wanted to change c4000 to a bridge but after watching your video and changing the settings you suggested, I didn’t get the result I was looking for. Maybe I just want to change it to an extender?

@MikeNovelli

3 ай бұрын

That is likely what you want to do. Good luck.

TP Link need to reward you big time! Thanks. Have you ever tried connecting a Bit Defender Box 2 to your network? It requires you own wifi router to be in bridge mode, My TP-Link Deco P9 mesh setup wouldn't work in Bridge Access Point mode because I didn't do the above. Now need to retry following about steps.

@MikeNovelli

2 жыл бұрын

I have never tried a Bit Defender box. Sorry. Good luck!

WDS Shows Run but im unable to connect to internet on my Archer A7 router

You da MAN Mike!!!

@MikeNovelli

2 ай бұрын

Thank you. I am him 🤓

Thanks for this video

@MikeNovelli

6 ай бұрын

You are welcome!

Thanks so much Mike, it did work , happy for your help, Wonder why when I set them.up with same name there is conflicts amd had each network with different name, how Can I set it up with network same name?? Thanks

@MikeNovelli

Ай бұрын

@@pedroluissirit7734 you can try giving them the same name. But you will not know which you are connected to by glance if you do that

Thank you so much!! Got my internet up and running

@MikeNovelli

2 жыл бұрын

Glad to hear it!! Good work.

my router is Archer A6, after configuration it works for few hours, and later the wifi says Connecting (obtaining IP address) and then no response.. so, I have to reset router again and do the same exercise.. painful almost daily 2-3 times i have to do it.

@MikeNovelli

Жыл бұрын

I would contact TP-Link support. If it is connecting and not getting an IP that might be an issue with the one you are trying to connect to, or whatever is assigning the IPs to the network.

Great video thanks! I was able to get the WDS status to run for 2.4 GHz band but not on either of 5 GHz bands on my C4000 tri band router. Any insight would be helpful

@MrWilsoniAm

Жыл бұрын

I too could only get the 2.4 to connect whereas the 5 still says Connecting. Did you ever figure it out?

Thank you from Colombia.

@MikeNovelli

Жыл бұрын

You are welcome from Chicagoland!

So i can connect my tp link router to my internet modem in my basement wireless and then it should work? And can if it works can i connect my pc with it ethernet cable?

@MikeNovelli

6 ай бұрын

If you do it correctly yes. And yes, if you follow the additional step I show that they left off their document you should be able to plug an Ethernet cable into the RJ45 port on the router/AP and access internet back at your modem thru the WiFi connection between the two. Give it a try! Hope this helps.

@hateax0n-yt460

6 ай бұрын

@@MikeNovelli i bought the tp link archer c50 and my modem is all the way in the basement and i dont want to put a 50 meter cable through my house so i can connect the tp link router in my room to the modem in the basement wireless and have wifi connection and ethernet cable connection?

@MikeNovelli

6 ай бұрын

@@hateax0n-yt460 yes. But you will be getting slower speeds than running the 50 meter cable. If you don't need speed then that's a good way to send the signal thru the air. Good luck.

Mate, you are an absolute godsend. Thank you🙏

@MikeNovelli

Жыл бұрын

You're welcome!!

Auto Time sync with NTP server not working in WDS bridge mode in Archer C6 V2. WDS bridge is working good. Devices connected to router can access Internet But the router itself is not connected to Internet. How to fix NTP issue ?

@MikeNovelli

Жыл бұрын

🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂🤷🏼‍♂ for ntp to work it has to have ip address assigned to it, that is able to access the itnernet. Make sure you have enabled that on the router. forum.mikrotik.com/viewtopic.php?t=63618

Hi, is it possible to do it with LAN cables ? Since wirelessly, the quality deteriorates ?

@MikeNovelli

Жыл бұрын

You mean like plugging the RJ45 ethernet port out of a main router and into the WAN port on the extender? You should be able to do it that way.

Bro this saved me hours of effort. Thankyou man 🫡

@MikeNovelli

4 ай бұрын

Glad it helped! 👍

thnx mike bro...you r really genius..

@MikeNovelli

2 жыл бұрын

You are very welcome!

Mike, I've been struggling with this for days, while I can configure my A7 into bridge mode I can't access it anymore. I tried both with the web address and the new IP but it just doesn't open the admin site. Any clues?

@sanithomer

2 жыл бұрын

Nevermind, fixed it 😄 While I knew how to put the router on bridge mode your advice on the ports fixed the 2nd biggest problem I had! Great advice sir! Best TP-Link Bridge configuration video!

@MikeNovelli

2 жыл бұрын

@@sanithomer Was gonna day try resetting the device and starting from the beginning. Or try the TPLink router URL instead of IP address. But if ya got it then that's awesome. Good work. 👍

@dukeboy1987

2 жыл бұрын

@@sanithomer how did you fix it

i have a problem it wont work!! i cant bridge a Wlan signal to another Router! i will use the main router with internet connection via WLAN to another router but it wont work! why?

@MikeNovelli

Жыл бұрын

I don't know. Not enough info provided. Please call TP Link Customer Service or send them an email. They should be able to give you some 1 on 1 guidance

You're a legend! Cheeeeeeeeeeeeeeeers!

@MikeNovelli

8 ай бұрын

👍 Thanks!

Do both routers need to have the WDS option? I'm trying to set up a TP-Link Archer A7 as WDS client, which has the WDS option, with a TP-Link AX3000 as host, which doesn't have the WDS option in its menu system. -- I've followed all of the WDS set up procedures I can find, including the above video, but cannot get it to work. -- The Archer A7 says "Run" in the status, but no ping, or internet. Should I keep trying, or is it impossible without both client, and host, having the WDS option?

@MikeNovelli

2 жыл бұрын

You need to make the one without the main router connecting to the modem and use the one with WDS to extend the first router. The first router is just broadcasting the WiFi SSID so it doesn't need it.

@duckmcdonald2492

2 жыл бұрын

@@MikeNovelli Ok, that's what I've been trying without success. I'll keep trying since you say it is possible. -- Thanks for the reply, and your video.

@MikeNovelli

2 жыл бұрын

@@duckmcdonald2492 try resetting the 2nd router and start from the first step on the guide. Try connecting to the TP-Link from another device and make sure you can get to the internet. If you can and then can get the same SSID pulled up when you survey you should be able to connect to that and finish the rest of the steps. Maybe double check with the guide that you are doing each one and in that order. Good luck! 🤞

@duckmcdonald2492

2 жыл бұрын

@@MikeNovelli I solved my problem. The TP-Link Archer A7 (the client with WDS), has three WDS modes (Auto/1/2). I've found that, if the host router is WDS capable, mode 2 is used, and for host routers that are not WDS capable, such as my host, a TP-Link AX3000, then Mode 1 provides better compatibility. The difference in the modes, is the number of MAC address they use to complete the WDS connection. Mode 1 uses 3 MAC address, while Mode 2 uses 4 MAC addresses. The auto mode obviously doesn't always work. As soon as I changed from auto, to mode 1, it started working. -- Your tip on bridging & turning on the Ethernet ports also helped.

@MikeNovelli

2 жыл бұрын

Glad you got it working dude. Thanks for sharing your experience. Hopefully someone else reads the comments and finds it useful. Cheers!

Can this method be used to make the to link router as a client so I can connect my ethernet devices to the wireless of my main router?

@MikeNovelli

2 жыл бұрын

Yes

I greatly appreciate this video. Had no idea how to do it and was struggling with it until I came across this video. It was a lot of help thanks a lot. Could you please not erase this video? haha I might need it again one day..

@MikeNovelli

2 жыл бұрын

It will stay up. Glad it helped you!

man is magnificent, ty so much, genious

Sir i have built connection using WDS between two tplink routers A and B . Router B has internet connection by cable network and In router A WDS is enabled but I cannot use the Access Control to restrict websites from internet on router A So i need help to maintain a internet connection from router A with some websites blocked Kindly make a video or reply and help me . Conclusion: how to use WDS and Access control on WDS enabled router at same time

@MikeNovelli

Жыл бұрын

Sorry sir, I no longer use my Archer router so I unfortunately can't assist you with this. Try reaching out to the manufacturer and their support system. They do have a phone number you can use to talk to a human being about this. Sorry I can't help more.

Hi, thanks for the video. But I am facing problem here with my Archer C6 AC1200 bridging to Airtel Xstream Router. After bridging everything works fine, but after power down (both routers power down), when my Archer router power back up it shows no net connection. I had to manually reset it everytime because of that. And also I can't access the GUI of my Archer router. I've changed it multiple times, like .50, .69 (like your's), .100 , but it doesn't give me access to my Archer router. It just says this address cannot be reached.

@MikeNovelli

Жыл бұрын

Try plugging directly into the router itself. Also reach out to TP-Link support. Sorry I can't be of more help.

@vrockandpop

Жыл бұрын

Did get any solution??😊

@BadassNemesis

Жыл бұрын

@@vrockandpop yeah. The version of that archer c6 router was v3.2. So for that version, I had to set the channel as static in the airtel router's 5g network (I was bridging the 5g network, so I set the channel as 44 in the airtel router) and it was working fine then. I was getting some random speed drop to 0kbps issue after that but it worked good for the rest of the time. But in March 2023 the archer c6 v3.2 router stopped working. After a restart it came online and asked for a firmware update, I clicked on yes and left the router for 1 hour. But after the update, the bridging scan stopped showing any networks (both 2.4 and 5). I tried everything, flashing old firmware, smacking it, trying to see if it detects any other hotspot's network, but it didn't. The wired PPoE connection worked fine when I put the LAN wire in it, but my main priority was bridging. So I bought a new archer c6 but this time it was v4. Now the bridging works great and I set the channel to auto in my airtel router and it still worked. I'm also currently not getting random speed dropped to 0kbps issues after using the v4 as bridging.

it this same as mesh?

@MikeNovelli

2 жыл бұрын

It's not exactly the same but very similar.

Can I use same SSID for my bridge router as my main? Will it cause any collision or problems?

@MikeNovelli

3 ай бұрын

You can try it but it might cause issues with knowing which one you're connected to.

Just got upgraded from FTTN (Fibre to the Node) to FTTP (Fibre to the Premises) and my ISP gave me the TP-Link VX420-G2h modem/router. I have been trying without success to use it as a modem only and use my existing Orbi Router and Satellites for WiFi connection. I was hopeful when i found this video.The interface is almost similar to what i can see, however, 'System Parameter' is nowhere to be found. Have everything above up to 'Traffic Statistics', but missing 'System Parameter'. Can't find WDS either to configure. I am thinking may be my ISP has set some restriction on the modem/router they send me. In the end, i set up the Orbi Router in AP mode. Unsure if the end result in terms of performance/speed is the same or not.

@MikeNovelli

8 ай бұрын

I'm not sure. But you should be able to just turn the WiFi bands off.

Thanks for the video bud! Just a question. If I follow your steps and run a cat5/6 cable from one router to the other. Will it automatically create a wired bridge? I want a wired connection.

@MikeNovelli

Жыл бұрын

It's not really "bridging" it if you do it by just plugging in the cable. You're basically just using the other router as a switch, but it's going to broadcast it's own Network. The Ethernet ports should still be on the original network though.

@neilmackinnon5573

Жыл бұрын

@@MikeNovelli oh okay. I guess I want the second router to act as a repeater then. I don't want to have multiple networks in the same house or do I?

Trust in my case it works fine ...I have done every steps properly but the problem it wouldn't sustain.after 2-3 days it goes same.internet automatically goes.then I have to repeat the whole step again and again what should I do now sir? please help me sir it will hamper my studies

@MikeNovelli

Жыл бұрын

I think you should contact TP-Link support and explain your issue to allow them to help you.

Thank you so much I was trying to find out how to do this and all the videos i could find were like a year old and the page they were on looked different so thanks

@MikeNovelli

2 жыл бұрын

You are very welcome. Glad it worked out.

A very useful function, that unfortunately is abandoned on TP-Link toutes and replaced with EasyMesh, that simply clones both bands, not just one, and doesn't have a dedicated backhaul - so the speeds on both bands are the same with the speeds from the band that is bridged in this example - that is, halved. Still, better than OneMesh, that doesn't even allow for 2 routers to be bridged. One model that still has the old interface and allows WDS bridging is AX6000 - get it while you can.

It's working, but after few hours it's shows no internet connection. Daily i have to do the same process twice or thrice... Very annoying

@MikeNovelli

Жыл бұрын

That's weird. Are you sure it is within range? Have you tried moving it closer to the source access point?

Thank you, Mike , please suggest after bridging , if the main router is switched off and on , then it is not working

@MikeNovelli

Жыл бұрын

You may have to run the setup process again.

Hello Mike, Thank you for this clear and concise explanation !! But I do not understand one thing. What is the utility of what you did at 2:56 ? You chose the 5ghz frequency for Wireless Bridging so the 2,4ghz is useless, isn't it ? I do not understand the "broadcasting" term you used I think ... Can you give me more details about that ? Thanks !

@MikeNovelli

Жыл бұрын

Broadcasting as in sending the signal out. You can choose either the 5 or the 2.4 but not both. Some older routers may only have 2.4 Whichever you choose is the signal that is going to be bridged and since 5Ghz should be a faster connection I use the 5. But the 2.4 is likely to penetrate further. If you are going thru a bunch of walls or when you survey you see 5Ghz connection much weaker than the 2.4Ghz you might want to choose the 2.4 However, the 2.4 on my main router is still broadcasting. Whichever you choose will not preclude the original router from broadcasting that other signal.

hello. please help me. when i hit survey, i cant detect the network that i want to connect. why is that? the network that i want to connect is available on my phone but i cant detect the network using the survey search . any tips? thank you in advance

@MikeNovelli

Ай бұрын

Are you trying to connect to 2.4 or 5GHz? Make sure you have the correct one selected before surveying. You may also need to move closer to the Access Point in order to receive the signal.

@mohdazwan8469

Ай бұрын

@@MikeNovelliim trying to connect to 5ghz one.. i able to detect my neighbor 5ghz wifi but i cant detect my own 5ghz signal from my own router in my house

I can't find system parameters in my tp link archer ax12. Is there anyway to bridge my router?

@MikeNovelli

4 ай бұрын

I would check the manual and then search support or contact TP Link if that doesn't help you

I use fixed wireless so the Cat6 coming into my house connects into a PoE, and then the PoE directs the signal to my router. Because of this I get Double NAT on my Xbox while gaming. If I set my router up with this bridge mode will that eliminate the double nat?

@MikeNovelli

Жыл бұрын

It might. support.xbox.com/en-US/help/hardware-network/connect-network/xbox-one-nat-error

Thanks 🙏🏼, there's alot of videos, do the same, but no one told that we need to Change the ip for LAN , for 69, and i do exactly as you said, and it worked, so thanks alot bro ❤ ** But can you further explain for the "LAN, IP address", and how specific we need to change it, so for someone who don't know anything about IP or router things, can understand, because i love to understand what I'm doing, not just copy and paste thing 😂😅

@MikeNovelli

5 ай бұрын

Try to find an app that will allow you to scan your current network for IP addresses. Each device is going to have its own. Most devices will automatically dynamically change their address when connecting, but you can set a static IP address for a device and have it keep that address always. you do not need to use 69. You just need to use a number between 2 and 255, but it's likely better to avoid 255, 254 and even anything over 200. Your main network device is going to typically assign itself a 1. I avoid 0 as well. Run a scan and see what all the devices on your network look like. There are free apps for smartphones, pcs, etc. Some will even identify the device by manufacturer and model. Hope that helps. Copy paste is good enough if it gets you up an running. But you can definitely change it from the Internet's favorite number if you want.

I managed to get only WDS working on 2.4GHz I have it on latest firmware release Archer C7(US)_V5_1.2.1 Build 20220715, any way my internet bandwidth is 500mbps and after the bridge I'm getting just 25mbps. So get a cable and connect it directly otherwise it will suck.

@MikeNovelli

4 ай бұрын

You're adding extra processing into the signal chain. The speed is going to slow.

very nice. thanks buddy. worked a treat. good man.

@MikeNovelli

Жыл бұрын

Thanks glad it helped!

After the router restarts i have to old the resett button for a few second and go through this again, daily. Any way to prevent this ?

@MikeNovelli

3 ай бұрын

See the pinned comment. It should alleviate that issue

@chiggo7742

3 ай бұрын

@@MikeNovelli oh damn i didnt see that, thanks mate

I get the status as run but still internet is not working

@MikeNovelli

2 жыл бұрын

That "run" is just saying it's connected to the other router/gateway. You would need to configure the internet on the router that is being repeated using this process. This process is not for the router that connects to the internet, it's for the repeater that connects back to the main router. If your main router doesn't have internet, neither will any devices connected to the repeater.

Works like magic

Can i apply the same process for archer c6 ac 1200?

@MikeNovelli

5 ай бұрын

I don't have that one but it should be a similar process if not the same

Great!!! Just a question. I was able to set my C7 but I lose speed in my connection. 200Mbs on the vendor Router and 40/50Mbs on my router. I'm enabled 5.8Mhz Any idea?

@MikeNovelli

2 жыл бұрын

Probably because you have a middle man (the router) between you and the original connection...

Hi Mike, I have Archer AX1500 & i couldn't find same options in my router for system parameters and WDS bridge, how to do it ? Can you please help ?

@MikeNovelli

5 ай бұрын

I'm not sure. You might have to follow a different procedure. I would search for their support document for that model or see if contacting support can help you. Sorry I couldn't provide more help.

@ausafe93

4 ай бұрын

​​​@@MikeNovelliHi, just for your info, a month ago i got reply from tp link USA support and they informed that this model Archer AX 1500 does not support the WDS set up.

@ausafe93

4 ай бұрын

& not all Tp link router have WDS feature available, only few models have.

Does it work when conected thru lan cable ?

@MikeNovelli

5 ай бұрын

Yes. That is why I made the video. The last step was left out in their procedure to enable the RJ45 Ethernet LAN ports with a connection. The whole reason I needed this was to run Ethernet cables to my mining rigs in my detached garage where there is no patch or RJ45 jacks. I had to run wireless signal from one access point to this Archer A6 and then plug into the ports on the back of the Archer. Good luck

Is this for if you want to use the router as wifi to ether adapter? So router connecte to wifi and pc connects to router connected to wifi?

@MikeNovelli

10 ай бұрын

It can work that way. It catches a wifi signal from another access point and makes it usable via wifi or the thernet rj45 jacks built into the device.

Not sure if it’s just me, but I keep having to reset. Follow all the steps but not sure if the TP link router is actually extending the Wi-Fi signal from my Xfinity Modem/router combo. Changed the IP, and did all the steps, but not sure if it’s extending…. :/

@MikeNovelli

2 жыл бұрын

Maybe try renaming the extended router's network to another name and see if you can connect at a farther distance than you were able to with just the Xfinity SSID...

Now after doing all these settings i am not able to connect

@MikeNovelli

Жыл бұрын

I'm sorry you are having trouble. If I were you I would contact TP-Link support and thoroughly explain the issues you are having with them. If you can try to get them on the phone have them hang with you until the setup works correctly. Good luck!

archer ax50 don't have WDS option how can i do that ?

@MikeNovelli

10 ай бұрын

It might be buried in another menu. Sorry, but you'll likely have to discuss it with TP-Link support.

This was super helpful. Thank you!

@MikeNovelli

Жыл бұрын

You are welcome!

In my case , bridging is successful in 5ghz range,but I’m not able to bridge with 2.4ghz band , I follow the whole process but Internet doesn’t work in 2.4ghz band and always run in 5ghz band .please help

@MikeNovelli

2 жыл бұрын

🤷🏼‍♂️ Make sure you are surveying using the 2.4Ghz and not the 5Ghz. Maybe try unchecking anything with 5Ghz to attempt to force 2.4 If you can get the 2.4 surveying and connect to an available 2.4 network it should work. But the whole process has to be done from the beginning with 2.4 in mind rather than 5. Good luck!

Thanks, but I'm having a problem. My speed is 350mbs and after setting up the archer as repeater the speed is worse ~60-70 mbps. Any idea why?

@MikeNovelli

Жыл бұрын

Because you are sending the signal thru 2 connections most likely.

my UI has half these things kept in completely different tabs. cant find the IPTV/VLAn to save my life

@MikeNovelli

8 ай бұрын

Yeah I think TP Link made changes or doesn't have consistency between different models. Sorry. I would contact their customer service.

Mike one question, it worked for me for sometime and this morning I was unable to connect to repeater router. Internet got disconnected and connection not worked after that. Any clue?

@MikeNovelli

Жыл бұрын

You may have to survey and reconnect again. Or sadly go thru the full setup process again

Thanks mike, very helpful tip. Can you tell me if this is possible with a Unifi network? I want to connect a tplink archer a6 wirelessly to my Unifi u6 pro AP purely so I can use the LAN ports on the back of the tplink a6 (not worried about having the A6 being able to extend the Wi-Fi at all). Unifi doesn’t support WDS though, so not sure if it would work. Can the tplink just connect wirelessly to the current SSID network the same as any regular client does, and then make use of the lan ports for things to connect?

@MikeNovelli

Жыл бұрын

I believe it should be able to. You just need to survey and connect to that WiFi and then setup the TP-Link correctly to enable the bridge

@skyliner967

Жыл бұрын

@@MikeNovelli awesome, thanks heaps mike. Very helpful.

I just purchased a TP-Link AX1800 (Archer AX20) and I was wondering if it is any different if I want to hardwire into the WAN port. My internet comes into another building with a main router there (Starlink) and then I have an 800 foot point to point system to my house so “hard wiring” is my only way to project wifi through my house. Any help or input would be much appreciated. Thanks

@MikeNovelli

Жыл бұрын

If by hard wire you mean running an ethernet cable to the RJ45 connector then you shouldn't have to worry about any of this. The router will use the built in switch to act like a normal switch for anything connected to the ethernet ports and the router can send a signal to act as a wireless access point on the same network if it is hard wired back to the original source. If you mean that you want to use the ethernet ports on the back of the router to receive signal but have the router connect to the network of a different device wirelessly then yes, the last step that they forgot should enable you to plug into the RJ45 ports with an ethernet cable and connect to the network/internet. Hope this helps.

@liammcnabb9274

Жыл бұрын

Ok thank you. I will see what happens once I receive my new router. I am just having problems with two routers on the same system currently and I am getting a double nat signal so I heard that bridge mode on the second router will prevent but my current second router does not have that option. Hence the new router purchase

Yeah its work , but i have problem here , when it become repeater , my epson print server apps notice me that my ip address have different subnet mask and i cant connect my connection with my printer, i dont know how to solve that

@MikeNovelli

2 жыл бұрын

Change to the same subnet