Unilumin 2.6mm LED Screen Repair #Unilumin #LEDSCREEN #Repair
Жүктеу.....
Пікірлер: 30
@sergiocaso7 ай бұрын
a que temperatura soldas los led y los desoldas???
@adsdiffusion50044 ай бұрын
👍🙏 Video tres bien expliquée, top, merci
@aire-entertainment4546Ай бұрын
How do you fix p3.9 outdoor dead pixels
@user-lg2ev2zb6m9 ай бұрын
could you told me all the tools you use in the video please
@mareknespechal243 Жыл бұрын
steady hands and good eyes, world champion :)
@hegelgutierrez947610 ай бұрын
Eres el mejor 💪🏼 si ke funcionó, en unos dias estaré subiendo el vídeo del proceso pero usando paper panel👌🏼
@josejuanalberto62453 ай бұрын
Donde consigues los led
@user-bb7he5wp6u5 ай бұрын
many many thanks
@muhammedhammoud1587 Жыл бұрын
Good evening .. If you allow, you can tell me how the LED path and how maintenance you have a scheme
@igor-davidmateus2716 Жыл бұрын
Like, do Brasil. Aqui é galo!
@ragnhildthelmersen6830 Жыл бұрын
Why are you using trackpads? Is that for when the module is damaged under the pixel?
@ElectronicsER
Жыл бұрын
Yes, when the track is damaged
@mieorj91414 ай бұрын
In the early video, You only change 1 piece yet later you change 4 pieces..why was that??.. For some one who wants to learn any books or guidence You could share
@tomaspalencia8772 жыл бұрын
How many C° and airflow did you use for the repair???
@ElectronicsER
2 жыл бұрын
I use between 300 to 350 more than that can damage the LEDs ,And the airflow is the lowest setting on the hot air. On the side part I use 300 then in the middle I use 350 C
@tomaspalencia877
2 жыл бұрын
@@ElectronicsER thanks, I'll try that settings!
@adithyawahyuputra9861 Жыл бұрын
what do you clean the remaining flux on the PCB?
@ElectronicsER
Жыл бұрын
I used alcohol in a spray bottle
@TeknisivideotronBanten Жыл бұрын
Yg disuntikan cairan apa bang
@senthilkumar-pj2yo2 жыл бұрын
Which flux used
@ElectronicsER
2 жыл бұрын
I used Chipquick Lead Free Solder Flux
@mehulpatel76852 жыл бұрын
And what is that little chip did you using..? And way and what are you testing…?
@ElectronicsER
2 жыл бұрын
I used spare LEDs and track pads to fix, then testing on test pattern to ensure LEDs are working RGBW
@vpgames1105
2 жыл бұрын
@@ElectronicsER I researched to buy this track pads but I couldn't find it on the internet, I found it better than putting the copper wire
@vpgames1105
2 жыл бұрын
I would like to know the name correctly so I can search
@ElectronicsER
2 жыл бұрын
@@vpgames1105 you cannot find trackpad online, you can find it from supplier of your LED panel from China, from manufacturer of LED.
@psmith6388
Жыл бұрын
@@vpgames1105 if you have for example Absen modules, find your nearest distributor and they will have all that.
@mehulpatel76852 жыл бұрын
Way i need to use Flux..?
@ElectronicsER
2 жыл бұрын
You need flux to ensure smooth flow of solder on the metal joints. The main purpose of using flux however is to remove oxidized metal from the surfaces to be soldered, seal out air thus preventing further oxidation, and by facilitating mixing it improves wetting
@oneinvegas4431 Жыл бұрын
The repair at 12:20 is horrible the pixels are totally not straight and will look like crap when next to another corner
Пікірлер: 30
a que temperatura soldas los led y los desoldas???
👍🙏 Video tres bien expliquée, top, merci
How do you fix p3.9 outdoor dead pixels
could you told me all the tools you use in the video please
steady hands and good eyes, world champion :)
Eres el mejor 💪🏼 si ke funcionó, en unos dias estaré subiendo el vídeo del proceso pero usando paper panel👌🏼
Donde consigues los led
many many thanks
Good evening .. If you allow, you can tell me how the LED path and how maintenance you have a scheme
Like, do Brasil. Aqui é galo!
Why are you using trackpads? Is that for when the module is damaged under the pixel?
@ElectronicsER
Жыл бұрын
Yes, when the track is damaged
In the early video, You only change 1 piece yet later you change 4 pieces..why was that??.. For some one who wants to learn any books or guidence You could share
How many C° and airflow did you use for the repair???
@ElectronicsER
2 жыл бұрын
I use between 300 to 350 more than that can damage the LEDs ,And the airflow is the lowest setting on the hot air. On the side part I use 300 then in the middle I use 350 C
@tomaspalencia877
2 жыл бұрын
@@ElectronicsER thanks, I'll try that settings!
what do you clean the remaining flux on the PCB?
@ElectronicsER
Жыл бұрын
I used alcohol in a spray bottle
Yg disuntikan cairan apa bang
Which flux used
@ElectronicsER
2 жыл бұрын
I used Chipquick Lead Free Solder Flux
And what is that little chip did you using..? And way and what are you testing…?
@ElectronicsER
2 жыл бұрын
I used spare LEDs and track pads to fix, then testing on test pattern to ensure LEDs are working RGBW
@vpgames1105
2 жыл бұрын
@@ElectronicsER I researched to buy this track pads but I couldn't find it on the internet, I found it better than putting the copper wire
@vpgames1105
2 жыл бұрын
I would like to know the name correctly so I can search
@ElectronicsER
2 жыл бұрын
@@vpgames1105 you cannot find trackpad online, you can find it from supplier of your LED panel from China, from manufacturer of LED.
@psmith6388
Жыл бұрын
@@vpgames1105 if you have for example Absen modules, find your nearest distributor and they will have all that.
Way i need to use Flux..?
@ElectronicsER
2 жыл бұрын
You need flux to ensure smooth flow of solder on the metal joints. The main purpose of using flux however is to remove oxidized metal from the surfaces to be soldered, seal out air thus preventing further oxidation, and by facilitating mixing it improves wetting
The repair at 12:20 is horrible the pixels are totally not straight and will look like crap when next to another corner